Reviews
It's not cosmetic, but I can recommend it to those who are obsessed with it.
I wanted to use a Fender Eliminator, but was looking for a product that would allow me to use an OEM inner fender for waterproofing near the battery box, etc., and came across this product.
But in the product information When installing the Japan License Plate, some modifications are required. As it is written, the mounting hole Pitch of Japan's License plate (120mm) The product did not conform to the
These and others are recommended for those who are comfortable with the additional processing of Inner fender's Cut and Bracket.
The car is legal and can be inspected without any problem.
・ "Daytona" Rear Blinker Bracket (For M8) _Item No.:23289
・ POSH." LED License lamp kit_Item number:500494
・ PLOT." Camera Bracket for Dora Recorder_Item No.:DRS001
・ "Daytona" High Cider Blinker PLOTn TWO_Item number:17308
The accuracy of cutting parts is good.
There is no problem with Fitting if the inner fender is processed according to the official YouTube video.
However, the license lamp and the Fender mentioned above interfere with each other, so we adjusted the mounting position by inserting the Spacer about 7mm. If I use the same TST license lamp, I am sure there will be no problem.
Although I had to buy a few more spacers and screws due to fitting with other parts, I was satisfied with the result.
View detail
Fits: HONDA CBR1000RR, HONDA CBR600RR, HONDA CB1000R, HONDA CB650F
TST TST Brake Light modulator
Was the installation difficult?
Simply interrupt the Wiring of the Tail lamp.
How was your experience with it?
I think it will reduce the RISK of being rear-ended.
[Included Parts:were they on?
Instruction Manual and Sticker are included.
[Was there anything that disappointed you?
▼There are 3 patterns of luminescence.
1, Electronic flash alert
FLUSH several times during initial lighting and continue lighting as normal.
2, PulsarBrake Alert
Continuous FLUSH when BrakeLight is on 。 This is a feature that is Standard Equipment on today's luxury and high-grade vehicles, or Race vehicles (Endurance Race vehicles, driving in the rain, etc.).
3, IntermiTentPulsar
There is a momentary pause between PulsarFLUSH "Intermittent." FLUSHPattern of the
View detail
Used for ninja250R
The blinker of the NINJA2 Helmet50R broke, so we diverted this one.
Cars with similar holes can usually be installed.
Unlike the OEM stick blinker, the Small is hard to see because of its poor angle.
I think the design is good and modern.
View detail
TST TeaST Reserver tank-lessKit
It was installed on a Yamaha MT-07 at the same time as the Fender Eliminator Kit.
I think the Reserve tankless is very effective in increasing the sense of reflection around the rear.
View detail
I love that it's got all kinds of designs in it!
I like TSTLarge.
All of my motorcycles are TSTTails.
View detail
Cosmic LED Flashing
I bought it because it is one of the cheaper LED blinkers and its shape is horizontal and not sequential.
It looks like a manufacturer in the United States, but there is an installation video on the official YouTube Channel, so I watched it and installed it and it went smoothly.
If you look closely at the finish, you can see some plastic molding marks and a little BALI.
I chose the Smoked lens, and I think it looks good without the Orange standing out.
View detail
It can be used without problems
Installed with no problems and flashes well.
The screw and nut of the mounting part are made of plastic, but I don't think it's a problem because it's not the part where the load is applied.
View detail
Easy Installation
I used it to install the company's Blinker.
I was able to install the Blinker with ease, but I thought it could be a little cheaper.
The installation itself went without a hitch.
View detail
Fits: KAWASAKI ZX6R, KAWASAKI ZX10R
It looks good!
[How is it used?
I wanted to make the Motorcycle look Black, so I just used the Stop-lamp.
Was the one you received as per Image?
Street Image
Was the installation difficult?
It took about 30 minutes.
How was your experience with it?
If you also use Blinker, you can Refreshing, but it won't pass inspection.
[Included Parts:were they on?
It came with a cheesy Relay.
[Was there anything that disappointed you?
I could sell it for a little less.
Other items that would be helpful
Request Maybe I should just use Stop-lamp and offer a cheaper version.
View detail
Can be used with JC92 * Requires processing.
I decided that this was my only choice for front blinker.
Processing is required for installation.
The Position light will not light up. <If you modify the wiring, it will turn on.
When installing, it is possible to install if the original Rubber cover is cut off with Cutter.
Because it cannot be fixed with PlasticNut of the attachment, it is fixed with TNut M10x25x1.8mm.
TNut sells them at Home center.
I'm sure there are individual differences, but only our Right Side is damp and cloudy. (Lol)
View detail
Fits: KAWASAKI Ninja 400, KAWASAKI Z125, KAWASAKI Z900, KAWASAKI ZX6R, KAWASAKI Z400, KAWASAKI Z650, KAWASAKI Z800, KAWASAKI ZX10R
Not so convenient
The functions of the modular are good but programming is a bit inconvenient because you need to open up the cover. Should have provide a small hole for adjustment. View detail
Too big NORMAL to Sharp
Installed on z125 pro
A little modification is required for installation.
However, the Blinker display in the Panel doesn't blink after I put it on, so I'm thinking about what to do.
View detail
Fits: HONDA CBR300R, HONDA CBR250R, HONDA CBR250R
Cosy, good looking, EMark certified product!
I bought it in order to replace the Front Blinker of '14 MC41 CBR250R with the LED Blinker of the embedded type.
Because the thing of the thing made of TST had the official introduction animation etc. on the Net and seemed to be the most decent product, the thing of the thing made of TST though the thing made of Hot bodies and the Chinese product were considered.
There are two types of fitment, easy fitting and full fitment.
Because Cowl is White, I chose Clear Lens which is not conspicuous when wearing it.
Big surprise when I saw the package that arrived, just a ZipBag with the product and mounting parts.
There is no Instruction Manual.
Well, it's inexpensive, so I guess they're cutting costs.
The quality of the product itself is comparable to other domestic parts. The Bullet Type Terminal is already installed, and the waterproof coking is done at the wiring exit. The price is very reasonable and the quality is excellent.
Also, I didn't have any explanation for this, so I didn't know it until I saw the product. This is a happy miscalculation.
Easy fitting, just replace the OEM Blinker. (It doesn't ExactlyFit, so positioning is necessary) However, the ear part of PlasticNut interferes with the inside of Cowl, and it cannot be installed.
No modification" means that the product can not be installed without modification;
So, it is necessary to shave the fat part of the ear of the image to a small size.
The fit is slightly gaping when you look at it up close, but considering the Cowl process, it's acceptable.
The brightness is honestly more than I expected and the visibility from the side of the vehicle is good.
Visibility from the front is not good because it is an embedded type.
By the way, even if I used it together with the Blinker positionRelay made by POSH which makes it possible to correspond to LED Blinker while keeping the Blinker position function of OEM alive, I could use the Blinker operation and the dimming operation at the time of Position without a problem.
For these reasons, we recommend the Blinker to those who want to embed the Blinker and refreshing the car body, because the quality is good for the price.
If you want to improve visibility purely, it is better to look for Bar type instead of embedded type.
View detail
The Material is a bit cheap.
I bought this product because the Blinker on the Rear does not look SMART.
Stop-lamp and Blinker are also available in several different lighting patterns, so I am very happy with them.
There was no installation instruction manual attached, but if you can do daily maintenance, I think you can install it easily.
It was also good that Wiring could be ponied to the OEM Coupler.
Unfortunately, the Material of the tail lamp was a bit cheap, but overall I was satisfied with the product.
View detail
Fits: YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA FZ-10, YAMAHA MT-10
This is a Harness that can be used for many purposes.
I bought these for my YZF-R6 (2019), and with the Conversion Harness You can use the Universal Product's Blinker without damaging the original Wiring. When replacing the Blinker with the Fender Eliminator Kit, you can use the Recommendation. View detail
Gorgeous!
I had quite a bit of trouble ordering them Make it just dress-up parts and expensive! You want to go that far with Grom? But We-Big's Campaign pushed back, and to my surprise, I popped it in a minute before the deadline!
This product is made in the US by TST Initially, we were told that it would take a month to order it, and since there's a Large confusion about the Corona virus Am I going to be late? I thought it would be a good idea, but it ended up arriving in 2 and a half weeks earlier than planned for Large It's a good thing that they're not too far away from a decent motorcycle shop But it's not as if there is no such a thing as a It's amazing that you can buy products from a company that doesn't have a presence in the market It's very convenient
When I opened the box, which was still sealed by DHL Seal, I found the product and the wafer wrapped in a messy packing material Only Big's slips were in there, no Manual Well, I don't need it Installation is easy, and TST provides a careful installation instruction video (I what (I've looked at it twice) I pulled the contents out of the packaging and oh! What a LusterLuster, Shiningly! Carbon rear fender for the Grom, there are several similar products available and they are made The products from in Thailand are a bit cheaper, but I'm a bit worried about the quality This TST product is made of Toray's Carbon fiber I chose this one because it's a very good quality The cleanliness, the goodness of the parenthesis, and the accuracy of the processing was as expected I don't know if you can see it in the photo, but it's a very wide plain weave, and it's just as good as you'd expect it to be Carbon Fibre pattern (not the pattern, but the real thing!) This is the first time for me to make a real fender It is quite complicated three-dimensional shape of Rear Fender is made up wonderfully by 1 Piece The weak point is the back side It is quite messy after pasting the Carbon Seat on the back side of this model It's a little bit uneven and textured It is not the place to worry about, because there is no need to look at the back side after installation
When removing (installing) the rear fender, it is necessary to remove the exhaust system The Fender stops at three 5mm HexagonalScrew The screw on the reverse side of the Exhaust System has an Exhaust If the exhaust system is left on, the tool cannot reach it Removal Removed OEM Material:PlasticFender and TST's Fender side by side, as you can see, the TST's The design of the Edge is a little bit small and the Edge is sharp Because it is not a heavy part to begin with, the shape up effect is small, but the Fender of TST is about half the weight of the OEM Product (I didn't measure it)
Installation was easy and secure, and it fit perfectly into the original screw holes and stayed in place There is a notch in the shock part, and it does not interfere at all Although it has been changed to NITRONR1, but the large most of the rare shocks are large and durable Turn the exhaust system back on and the work is done
What do you think, Custom is just a functional part, not a dress-up! But when the Carbon fender came on, what a surprise! It's only carbon It's only Carbon However, I like this kind of thing, don't you, boy? I also like to use aluminum machined products This little grommet has finally become gorgeous Shiningly is cute By the way, TST has also released a Carbon Front Fender, but I don't have any plans for it I don't, because I think Red Fender is better in parenthesis But I think the quality is perfect for Front too Many of them are very expensive, so this TST product is not too expensive Custom parts for groms are always cheaper than for Large motorcycles! So it's a great place to play with things
Now, what's the key running fee Ring? It's not going to change To say the least, there was nothing wrong with it You can't see it while driving, so you forget it's even on However, I can assure you that you will be woo-bird every time you get off the bike If you're an engineering guy like me, who likes aluminum and titanium chunks, you'll love it! ! It's not a theory
View detail
Fits: YAMAHA FZ-07, YAMAHA FZ-09, YAMAHA FZ-10, YAMAHA MT-07, YAMAHA MT-09, YAMAHA MT-10, YAMAHA XSR700, YAMAHA XSR900, YAMAHA YZF-R3, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R6s
Will the car pass inspection?
BrakeLightMODE:Standard、Pulsar、Electronic flash。
A modulator that allows the StopLight to blink when braking
Installation is as simple as connecting to the OEM Coupler
Instruction Manual was not included, but if you imitate the operations in the video, you can use the Easy to adjust
The blinking speed depends on the number of times of blinking (10 times blinking), so you can make the blinking speed faster Then the flashing PatternCycle is too fast and a bit lame
I wish I could adjust the blinking speed without changing the blinking time
It always works during braking, so if there is a system that works during rapid deceleration or high speed deceleration, it will work It's even better if it's a good idea, but it's not going to be possible at this price, and Wiring is going to be complicated
The same Coupler from Yamaha seems to be able to be installed, but I'm not sure if it will work
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA FZ-07, YAMAHA YZF-R3
Scratch
I ordered from singapore and takes 4 days to deliver. Fast delivery however when i checked the item have some scratch the packaging is ok but i don't know why some scratch. View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA FZ-07, YAMAHA YZF-R3
Trusted Delivery
I'm Anwar from Malaysia. Shipment take time around 18-19 days for item delivery. Satisfy with item, delivery and condition product. Easy to install. Just plug and play. View detail
Refreshingly nested and sharp looking!
It seems to be easy to install, and it was a big deal to fix it in place with the Bolt (I'm clumsy...)
When the installation is complete, you can see no ugly bolt holes, and the Refreshing is in the Large I'm delighted with the Sharp look! This is a recommendation for those who do not have any numbers in a circuit
View detail