Reviews
It is Large strange to remove the Meter.
It was LARGE weird to remove the meter. Pay a labor charge and have a store do it! View detail
The installation diagram is confusing and the Meter cannot be removed.
It's OEM, so the price is not an issue, but the Harness pull is very confusing and distressing. View detail
Socket Accessory instead of USB
It is Socket Accessory, not USB.
USB Type is available from other companies, but I chose this type to use Compressor.
Puncture repairs would be helpful.
View detail
Fits: HONDA CBR400R, HONDA CBR400R, HONDA CBR400R, HONDA CBR500R, HONDA CBR500R
Seat heater power supply extraction
Required tool
Hexagonal Wrench6mm
Nipper (Cut Tie Wrap)
scissors (Cut into ConnectorCover)
Vinyl Tape (Wrap around ConnectorCover)
Driver-like object to remove Clip
The Installation Instruction Manual must be downloaded from Net.
Used to install Komine's Seat heater.
Remove the Pillion Seat, Seat, LeftRight Side Cover, and Rear cowl in this order.
Side cowl has the front hooked to the claw of the Frame.
Two Pins are inserted into the Frame's Grommet and are slowly pulled forward.
Rear cowl inserts the lining remover between it and the Fender and pulls out the nails.
If you try to put it on according to the Instruction Manual, you will get
One Tie Wrap is missing.
The shape of the Dummy plug that connects to the empty Connector did not fit.
The Clip that stops the Rear cowl on the back of the Socket will not fit.
I figured the easiest way to connect the Seat heater to the Attachment would be to use the
In the case of the Motorcycle, the Battery area is concentrated under the Seat.
Even if Attachment power is taken from the vehicle body Harness
If you use Relay, powered by Battery, you can still use it.
I don't think it took that much effort.
View detail
Attachment rather than an essential OEM Product
HondaOEM's Socket and iphoneSE will run out of battery in less than half a day.
I think it's because the iphone doesn't have that much battery to begin with and Navigation eats up more electricity than I thought.
I know this is off topic, but if you are going to be doing longer touring, the Socket is a must.
I think webike is a better deal for the Points than Honda Dealers!
View detail
For Attachment power supply
It is OEM Attachment part, so the quality is good. However, it is not USB port type which is popular nowadays, but Cigar lighter type. Is it a common attachment part with other Honda cars? There is no instruction manual for installation. View detail
Just fit to the Cigar socket slot
Finally, the CT125 CT110 HUNTER CUB was delivered today, so I bought it in Large quantities. Start installing certain outfitting items.
Naturally, we'll start with the electrical Attachment.
I don't even think I'm going to go running without my Navigation replacement, Ta-Brett, sitting on the ground. because it is not there.
There is a special slot on the Key cylinderLeft of the Top Bridge, and the Grommet This is a perfect fit when you pull out the
As expected from an OEM product, there is no positive reason to choose any other product
If you want unlimited Ampere, just use Battery directly.
The included rubber cap fits really well and will not come off on its own at all.
There is no instruction manual and Attachment feed to the Manual of CT110 HUNTER CUB side. No mention of Coupler.
Short Harness and WaterproofCoupler, so you can use it from the Top Bridge There's definitely a pair of Couplers in the not-too-distant position! Think ………
I looked into the back of the Headlight Assembly but could not confirm it.
Then! I removed the Frame cover and checked the Battery, but I couldn't see it.
The correct answer is inside the Headlight AssemblyCase & omega;
Here, a pair of water-proof couplers of the same color sit with a Blind lid. It was.
Remove the headlight unit with the coupler and try to pull out the Blind cover, but it is not possible to remove the headlight unit. Terribly hard to get out of ………
In any case, I have no intention to reuse the Blind lid or anything like that, so I'm going to use Nipper for the nails from the beginning. It would have been quicker to chop it off & omega;
By the way, the ManufacturerOEMGrip heater also feeds this power Since it uses the WaterproofCoupler, the combination of these is not technically possible.
Of course, I don't think the 125 single-cylinder Generator will force you to do anything, but it's a bit overprotective. ?
I'm a paranoid and my wrist is damaged and I don't use a grip heater because I prioritize the anti-vibration Gel grip. I don't have one, but ω
I thought about making the direct Battery wired for convenient charging in Garage, but this time I also decided to make up Harness for Charger separately.
The CT125 is going to be my last toy, so I didn't want to push him too hard from the start.
View detail