Reviews
Knuckle guard and Extension
I referred to the Instruction Manual on the Manufacturer's website and was able to install it without any problems. View detail
Choice of OEM
I like Parenthesis for Other Brand Product, but I choose OEM Product every time I buy an off-lease car.
Fits well and inexpensive No problem at least with stepping stones and branches.
View detail
I was able to install it without asking the store to do so.
The installation was done in the summer, but I had the opportunity to remove the cowls and wanted to install them at the same time.
We have prepared the materials and worked according to the instruction manual and it is working well.
Installation on HondaFORZA250 (MF15).
IMPRESSION DETAILS
0Package
Another Option is needed.
The packaging is very careful and, as is Honda's way, there are more Tie Bands in the package than necessary.
(It's a weatherproof Band, which helps)
0Required materials
・HondaBondA
https://www.webike.net/sd/23438651/
・Parts cleaner
(I bought the Plastic可 product)
0 Installation Point
Left Side:Smooth when BondA and Parts cleaner are used when this product is installed.
Right Side:Remove and replace the end of the wire on the Engine side to prevent damage to the wire if the Throttle Wire is forced to be removed.
No drilling was done on the handlebar cover, only tie bands were used to hold it in place.
(extra Material):(RubberParts was used in another case)
Coupler connection is not difficult if you follow the instructions.
0Others
I've seen YouTube videos of grips getting sticky over time, but mine is still Large and sturdy. I would like to see how it goes.
That's all
View detail
good-looking
I bought it because the photo of the vehicle with Knuckle guard on the cover of Catalogue of 2022 MODEL is Parenthesis good.
The actual product is as expected and I am satisfied with the windproofing as it works well. Neck that the price is too high.
View detail
In EngineOFF, Battery protection is activated.
I used to love electric heating Gloves, but I decided to use Grip heater because of the hassle of plugging and unplugging the Cable. It is out of season, but I had a lot of Points saved up, so I bought it anyway and was going to install it before winter, but now I have time to install it.
The OEM Grip heater is more expensive, but we chose it because it has a function to stop power if the battery voltage is low to prevent the battery from going up.
Installation requires disconnecting the cowl and removing the power supply. If you are new to the ADV150's electrical system, we recommend that you gather sufficient information on YouTube, etc. before starting the work.
If you choose OEM, please note that the Throttle pipe is fixed to the Grip, so it is not possible to replace it with High Solo's Throttle pipe. Power is supposed to be supplied from the ACC power source at the front end of the Cowl, and to prevent accidental wiring, the terminals are divided into Female and Male. The power supply is connected to the power outlet port harness.
I have not used it yet because it is still summer, but when I tried to turn it on, the battery protection function is activated when the engine is stopped and the power does not turn on. I don't use Idling stop, so it is not a problem, but be careful. Another thing I noticed is that the Left side seems to get hotter than the Right side. This may be an individual difference or may be influenced by the presence or absence of the throttle pipe. One more thing:The intensity can be adjusted in 5 levels, but there are 3 LEDs to indicate the intensity, so it is hard to tell if 4 is dark-light, 2 is light-dark, or 1 LED is dark-light.
The grip will be slightly thicker, from 32mm to 34mm in diameter, but it will not feel uncomfortable to hold. Also, the length of the Grip will be about 5mm longer.
View detail
I haven't used it yet, but I'm hopeful.
I haven't used it yet because I haven't ridden it in the middle of winter, so I don't know the effect, but I am sure it will be warm. View detail
OEM Product is still the strongest
OEM Product is the strongest.
Grippe is consumable and OEM can be expensive, but the value is evident the moment you press the Button.
With the Handlebar Cover, you can use summer gloves.
View detail
Beautiful installation unique to OEMOption
Basically, there is no car model Exclusive Design for Third Party products.
(Although it may be necessary to shift the lever holderetc. or make other adjustments when installing it.
This product is an OEMOption, so there is no such hassle.
Looking at Guard properties, it has no Frame, so it is only a protection against cold, grass and branches.
Since it is less than half the price of a high protection product, it is recommended for those who are willing to put it on for the time being.
I think you should take a good look at OnLineManual because there are similar components.
View detail
It looks subtle, though.
The protection is subtle, the DL1000 V-STROM250's Knuckle guard seems to be a little stronger and a little less reliable, but it's an OEM product that can be bought for $5,000, so I think it's totally worth it. The shape and color may be controversial, but it's easy to install and I think it's good. View detail
HONDA Honda knuckle guard
This is an OEM Product, so the quality is good. This is not the current model, but an Option product of the previous model.
Installation is no problem
View detail
Processing is required if you are using Lever of Other Brand Product
I bought this for my '19 400X.
[Mounting]
U-KANAYA AluminumRetractable Lever TYPE-R I'm using the
Clutch SideLever interferes.
Therefore, it was necessary to cut the Knuckle guardBody and the Genus Gold Bracket.
There is no problem with the installation on the Brake lever side.
[Effect]
I put it on hoping it would provide some wind protection during the winter months.
It didn't work as well as expected due to the narrow vertical direction.
(Maybe my expectations were too Large)
However, the windshield effect itself is sufficient and I like the Design.
View detail
Processing is required when using Other Brand ProductLever
I installed this on my '19 400X.
[Mounting]
Lever. "U-KANAYA's Aluminum Retractable Lever TYPE-R" I'm changing it to
It interferes with the Lever on the Clutch Side.
I had to shave the Knuckle guardBody and the Bracket for mounting to avoid the interference.
There is no problem with the installation of the Lever on the Brake Side.
[Effect]
I bought it hoping it would provide some wind protection during the winter months.
Knuckle guardBody was a little narrow in the vertical direction, but not as much as expected.
(Maybe I was expecting too much.)
However, I feel that it works well and I like the Design.
View detail
Adventure feeling Up.
It is neither possible nor impossible.
The product itself is not so Large, so it does not dramatically improve the thermal protection.
It's better than nothing, I guess.
Design is safe and organized.
The installation itself is easy, but it's hard to remove the Bar End ….
If I didn't RenBarrel the Impact Driver at my local Home center, I probably wouldn't have been able to remove it.
If you can't remove the Bar End, you might want to use the Universal Product of Mirror Co-closing Type.
View detail
Installation of new PCX125 JF81 before delivery
I had it installed at the shop before I took delivery of my new PCX.
Excellent in the middle of winter.
To use it, use it at the maximum heater temperature, and when it gets hot, lower the temperature gradually.
It is a half lap Type, so it takes a little time to warm up 。
Especially in the middle of winter, my hands get so cold that I think my fingertips are going to burst, so having a grip heater makes a big difference.
If you use Knuckle Visor and Handlebar Cover together with Grip heater, your hands will never get cold.
However, because the grip becomes thicker than NORMAL, I think there is a sense of discomfort at first, but if you get used to it, I think Large is strong.
The other thing is that the price is expensive.
It has a built-in battery lift protection system, so you have to buy it as an insurance premium.
View detail
Be careful with vehicles equipped with external Lever and external Screen.
I'm replacing the lever with a DAYTONA one.
Clutch Side interferes
interference part (Part of Bracket and LeftGuard) I used a sander to cut and install the
If you cut the Handlebar as far as it will go.
Handlebar Guard and Screen (Made by GIVI) does interfere with the
I can do Handlebar Lock without any problem.
View detail
Fits: HONDA Rebel250, HONDA Rebel500, HONDA Rebel300, HONDA Rebel300
It's about what you'd expect.
Adjustable features that are standard equipment on the 500cc Rebel but not on the 250cc.
I wanted to move the brake levers a little closer together, so I bought and installed a reliable OEM product.
The function of the product is as expected and there is no problem with the installation of the OEM product.
Just why is the shape different from the standard fitted Lever?
It has less curvature than the standard-mounted Lever, and it feels a little more uncomfortable when it's first installed.
Well, you'll get used to it, though (laughs).
I'd like to see the Clutch Side Adjustable Lever released as well.
View detail
I haven't installed it yet, so I can't evaluate all the items.
I have not installed it because there is no Installation Instruction Manual.
I can't wait to install it, I want to install it nicely according to the Installation Instruction Manual.
Can I get a copy of the Installation Instruction Manual?
View detail
After all this time … pretty good
It's warm enough for me to wind it halfway around Removing the Screen was a bit of a hassle to install, but it wasn't particularly difficult (If you remove the Screen, it's for the Sole? Bullet Terminal of the Bullet Terminal is out) It's pricey, but worth installing if you ride every day, even in the winter View detail
Fits: HONDA gyro canopy, HONDA monkey, HONDA PCX125, HONDA gyro canopy, HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA DIO CHESTA, HONDA DIO CHESTA, HONDA DIO CHESTA, HONDA DIO CHESTA, HONDA LEAD110(EX), HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA BENLY50110, HONDA BENLY50110PRO
You might want to put it on when you deliver the car
I use it with my PCX150 I think it's better to use it with Knuckle Visor in the middle of winter
Throughout the year, when the Gloves get wet from an unexpected rain, it helps to keep them dry and I think
The battery voltage can be monitored conveniently
View detail
HONDA Sports/Grip Heater
There is no installation manual, the installation is not convenient, you need to explore the installation method yourself. View detail