Reviews
Fits: HONDA CBR300R
If you can enjoy processing as part of the customization process
It's hard to put a bag on the Pillion Seat because of its smallness and excitement, these days The concept of solving the loading problems associated with the Sports model & the concept of "hellip It is a good product But the build quality was still overseas quality
What made you decide to buy?
Move the Top case to the Pillion Seat instead of the Carrier, which is far from the center of gravity I was worried about how to process the normal seat because of the material etc For
How was your experience with it?
Advantages over Rear Carriers
It's not impossible to do it with the Rear Carrier, but it's much easier with no tools required It's easy to
When I see the box on the carrier of the car in front of me bouncing around, I feel a sense of stability and a hellip It's harrowing
There's plenty of room to spare considering the weight of a human being
Advantages over the normal seat
Flat Shape
Hard top panel
HookPoint
Was the installation difficult?
It arrived a little over a month after I ordered it, and I assembled it and now install it … I couldn't I was prepared for this, but when it is impossible to install it, it will be a shame I'll get back on my feet and look for the cause with Base only
The Hook is too wide
First of all, on the front side, the hook on the loop of the body frame is extremely wide and I shaved with File and rounded the corner at the same time If it looks well, Quantity:Pair (for Left and Right) The bend angle is different in the
The legs are too long
Hook is in, but this time it can't be pushed down to the locking position If you remove the legs, the lock will be engaged, which means the legs are too long Shave it off and check it against the body of the car, then adjust it so that the four legs are grounded at the same time as it locks, and then remove the legs I did
After working on the base up to this point (it took me three days), the next step is the top plate, but fortunately there were no deviations A few dents and slips etc. are well within the acceptable range
The attached Sponge is attached to the inner circumference of the car to accommodate the gap between the car and the body I cut the front side thinly around the Grab Bar It has a rubber sheet on it
【Please tell me the installation point and hang】
If the legs are too long and need to be shaved, lock them in place with the Rubber feet off and from the side Measure the amount of shaving by applying a Rubber foot Finally, the lock and four legs should be grounded at the same time so that the load is not applied to the lock only Vinyl Tape is useful for the fine adjustment of the over-sharpening
The rubber sheet is cut to match the shape of the front of the top plate, and is attached by shifting it by about 1cm It was
[Was the Instruction Manual easy to understand?
It's only available in English version and German, but you can understand it by looking at the picture If you have a junior high school student's level of reading comprehension, you will be able to understand Large You can
[Included Parts:were they on?
Bolts and nuts for assembly, Rubber feet, Sponge for sealing the gap, Hole in the top panel Cap and Emblem for attaching it to the top plate
There are other parts to deal with the gap on the front side, which are extremely A separate rubber sheet is available as I mentioned above because it is not easy to use
[Was there anything that disappointed you?
I thought Germany would be a little more accurate
Do you have any wishes or improvements you would like to make for the Manufacturer?
Check the product thoroughly before shipping
If you use it in such a way that you put the homsen box directly on it, the warp of the back end is in the way, so you can leave it flat or use it in a different way You'd better point it down or else
[Do you have any products to compare it to?
None for the one and only If I had to choose, I would say Rear Carrier
[Others]
The weight of the finished product is about 1.8kg Because the thickness of the top board is 5mm though it is Aluminum, it has a feeling of weight in its own way The front and rear length of the plane part is almost the same as the Normal seat seat, and it is the largest size of SHAD Base(SH48etc.) just fits in this size But Screw hole is not fit, so you need to drill it
I know it looks convenient, but what I'm still wondering about is the price I understand the effort to develop a fitting for each car type, but I would like to have more functionality It's a shame, because it would be easier to get your hands on them if they were cheaper
View detail
Fits: HONDA CBR650R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CB650R, HONDA CBR650R
Loading Capacity Up?
Even if you don't have this product, the CBR650R will have no trouble securing the bag, but it has a Homsen box I bought it because it looked like a white surface to do so
There are two holes in the back and the side of the body that are not in the picture It's available
I screwed two long eyes to the front side where there are no holes
View detail
Fits: HONDA CRF1100L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin Adventure Sports
It is well made
It was installed at the same time as the Tank Guard
There were scratches etc. because it was made overseas as well as Tank Guard Installation did not go easily, and device and small processing were necessary
After all, the included bottles are not so accurate, so it is better to check them before you install them Recommendation
However, both Tank Guard and Engine Guard are good with no modification on the body side
Looks good parenthesis too
Then there's the power of the fall
I can't Recommendation to a nervous person, but it's a hurtful Parts anyway So it's OK
View detail
![[Repair / Option Parts] Auxiliary Bracket For Tank Guard](https://global.webike-cdn.net/photo/impression/fb/fb283517983efe0ef0f09f7bc2d9d71bL.jpg)
Fits: HONDA CRF1100L AfricaTwin Adventure Sports
Reinforcement of the Guard
I bought it to reinforce the Tank Guard I didn't want to be without it, so I installed it
By attaching the Auxiliary Bracket to the Cowl next to the Radiator, you can use the Only the Bolt side interfered with the Frame side because it was a single bolt stopper
It's solid and looks like it will be strong
View detail
Accuracy is not bad and Firmly attached
It's Made In GERMANY and has a bit of a Large taste, but it's easy to do without any weird processing It does not interfere with the Cowl, nor does it interfere with the Seat Unlike other products, Seat's closing is not affected It can be used as a HookPoint It's a bit expensive, but it's a good choice View detail
Fits: HONDA CRF1100L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin Adventure Sports
For being so expensive, the construction was crude
Since the car has only just been released, there are four different types to choose from, and the Hepco& Becker is the one with the look Purchase
When I received it and opened it, the first thing I noticed was numerous scratches and paint peeling I even wanted to return it, but it took over a month for it to arrive and when I asked for it back, it took probably another two months I gave up as I waited for about a week
It doesn't come on easily
The accuracy of the bottle is too low, so it cannot be tightened, and it is not possible to remove it I bought another bottle
Because the hole on the Guard side does not fit the Smaller Bottle, I had to widen the hole
It came with me anyway, but I regret that I should have gone with OEM
And the instruction manual is in German (？) And I couldn't read myself at all
Now all you have to do is hope that it works when you defeat the Motorcycle If you can't guard it, it's Garbage
View detail
It cannot be installed
Since the Instruction Manual is in English, you can use the
Maybe there's a misinterpretation
The screw part of the Bolt is not the right length
It cannot be installed as is
I think you can install it if you have the right Bolts
View detail
Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000
The Rear Sets are now the loading space!
I'm using it to install GIVI's Mono-lockSeries!
The GSX-R1000R is an Other Brand Product, but also has a Rear Carrier Because it is not sold and Seat bag does not have enough carrying capacity and water proofing performance For large capacity loading & security & waterproofing, a rear box is installed Decision Purchased
The price is a little high, but when I installed it, Large processing is not necessary, and it is a little pompously installed I'm happy with the installation and Large variant!
As a general comment, there is no large wobble, and I can use Rear Sets and Carrier depending on my mood It only takes me a minute to make the switch
I don't want a permanent Carrier on a regular basis! I only need to use the tear box for touring This is very much a product of Recommendation if you're not!
(There is a slight reluctance when locking to the Rear Sets, so if you are concerned about it, the Rear rack side may need to be beveled a bit.)
Normally, in the case of the Rear Carriers like Pipe, the maximum loading weight is about 5kg Subtracting the weight of 5kg of the tear box, the weight of the load can be reduced by putting the tear box on the ground I guess it's fated to be in the mainstream state of Limit and not be able to put anything too heavy in it the..
In the case of Rear Sets replacement, there's no Risk to break, so I'm pretty comfortable with that!
When you put a heavy object on it, there is a possibility of damaging the lock part of Seat measure
Please refer to the following instructions for installation
When you install the Base of GIVI Mono-lock, you need to check the position of the hole on the Base side and the position of the base The holes on the rear rack side do not fit perfectly, so be careful
The two holes in the original and the Gold genus on the reverse side of the rear rack Replace the bolts holding the parts with GIVIBase parts and tighten them together (See the second image of the image)
It is necessary to fix the GIVIBase side of the Bolt 3 points, but the Bolt that comes to the Center In order to fix the top cover of the Base, you must turn the part where the screw holes are located into a Drill or Nipper Drilling process by using a (Image Quantity:1 Set of 4 pcs. See eyes)
? Plug the holes on the side of the rear rack that you are not using with appropriate tape (See the sixth image.)
Use three bolts attached to GIVI to fix the base and the rear rack
At this time, because it was judged that the wavy Plate of GIVIBase attachment was unnecessary, Home I installed a Washer purchased at center instead (Refer to the fifth image of the image)
? When you install it as it is, there will be a large gap between Seat Cowl and the side of the rear rack You will not
Because of the gap of about three centimeters, rain and dust can get in as much as they want, and if you work hard enough, you can take out the stuff inside Level, so it's a Waterproof Crevice Tape sold at Home Center (Thick Sponge that won't soak up water) Overlap and paste (Images 3 and 5.)
View detail
Fits: BMW R1250GS, BMW R1250R, BMW R1250RS, BMW R1250GS
worst case scenario
I thought you were able to confirm that things were missing at the time of ordering If the item is out of stock, please remove it as soon as possible We have had similar cases before I am in disbelief View detail
Fits: HONDA CRF1100L AfricaTwin, HONDA CRF1100L AfricaTwin Adventure Sports, HONDA CRF1100L AfricaTwin, HONDA CRF1100L AfricaTwin Adventure Sports
Translation (please enter here for installation)
The texture is good and cool, but the translation (no instruction manual to enter here) is a bit I am anxious
It came with a 6mm Rubber, but I didn't really know how to use it
View detail
I'm happy with the way it looks
The bike is a heavy motorcycle and I have to stand up a lot so I installed these I am very happy with the way they look and feel The performance is great (confirmed by the standing position) and the body is protected View detail
Total side protection
These guards are going to be "instead of" a pipe guard, radiator guard and engine guard. It is also claimed to protect my foot in a tip over where the bike is resting on my foot. It prevents the foot from becoming trapped between the engine case and the ground. These also have the benefit of carrying a small bag on each of the guards. I'll have them so I cam remove the small bags when I go off road in tight single track. Though they make the bike about 2"wider, on each side, they are worth it. This is one item that is function over form. View detail
Fits: SUZUKI GSX-S750
It's pretty heavy
GSX-S750 with Hepco & Becker Tandem seat replacement rear rack I installed it I removed the existing Rear Sets and assembled the iron plate seat, but it was very heavy Sea Truck is well made, but there is a gap, and it was made of Urethane sponge Double-sided tape is attached to fill the gap It seems to be able to get out of the rain somehow, but I am worried whether the rain will penetrate from the Urethane sponge at the back It is I thought something needed to be done here But it's a very expensive product, and it's a money grabber for carrying a load You can also use this to install a rear box This is the best solution for a motorcycle with a bad loading capacity View detail
Fits: YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP
You're not going to buy it
If you don't have the Pillion Bar, you can't get it up with the Single Body
I suppose you could stand it up with something thicker, like a magazine or something, and then you could stand it up, but then you'd be better off without it I felt it
View detail
Fits: KAWASAKI Z1000
Fit feeling beyond expectations
If you install the SeatBack on the OEM Tandem seat, it will lose its shape, but It is not deformed, tightly and stably fit and secure
It is easy to install and can be installed in less than 10 minutes
View detail
Fits: DUCATI Multistrada 1200 Enduro, DUCATI Multistrada 1200S, DUCATI Multistrada 1260 Enduro, DUCATI Multistrada 1200, DUCATI Multistrada 1260, DUCATI Multistrada 1260S, DUCATI Multistrada950, DUCATI Multistrada950S
very good
The shape of the blinker is so exquisite because it is only for the car model Large Satisfied
The height of the Guard is fixed, so when driving off, the Brake or Clutch If you want to change the height of the lever, be careful because you will only be able to move a small amount
Lever height can be changed if it is about 5mm up and down, but if it is more than that, it is not possible to change the height of this Guard and Blinker interferes
View detail
Fits: DUCATI Scrambler Sixty2, DUCATI Scrambler 800
Low accuracy
It gives me the peace of mind that it's better than no Engine Guard
? The Screw pile of the included Bolt was distorted and was not useful as it was
? The molding accuracy of each part is low, or it cannot be installed without forcing it into position
? There is a part where the plate bolts hold it in place, but the head of the plate bolts is not inclined to fit in
? In my case, the OEM footpeg, in the Lever position, my toes are in the Engine It may interfere with the Guard, which may interfere with the operation of the rear brakes, and may also interfere with Shift It may invite mistakes
View detail
For those of you with gold
Visibility is certainly improved However, it is difficult to operate the keys because the adapter is located above the key cylinder Since the Mini Cowl is attached, it becomes even more difficult to operate, and eventually I had to remove it I thought the meter relocation kit from the store SIMPLE was better I think View detail
Fits: BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT
Generally, I'm satisfied
I bought it because I wanted a well and a handle around the seat
It comes in handy for getting in and out of the garage and for tying the luggage to the Seat
Quantity by widening the front slightly during installation:Set The positioning of the holes was just right
The front mounting is on Hexagon Socket plate Screw, BMW Most of RnineT's Screw
Because of the star-shaped Torx screw, there will be no unity But it can't be helped because it is a special screw
Cost should be a little cheaper, I think
View detail
It is hard to install
"I want Engine Guard to prepare for any chance, but I do not want to become a learning car ... .... "
When I thought I found it, I got it love at first sight and bought it!
"Small firmly feeling with swinging will surely protect you ....... "
If you say what to put on stand up in the second week!
Imagine awaiting and immediately wake up and check for scratches.
"Is that soil at the end of Handlebar ...?"
Apparently, it seemed that Handlebar and this Guard first contacted the ground and protected Tank, Engine, footpeg and others. Thanks! I will not beat it anymore! (Even if I kicked out about 20 times out of compression, it did not take Engine ... .... )
Function and appearance were satisfactory, but the installation was Large strange.
The Instruction Manual was German! Well as I expected.
Although there are few mounting parts, Bracket where Frame and Engine are fixed (I feel that it was a part like Curry 's Nan) Instead of tying this bodys together, this is a hard time.
There seems to be some distortion in the product, Quantity : Pair (for Left and Right) Do not match if the hole positions do not match.
The hole position was up and down 2 cm. Even though PenetratingBolt .......
With Driver, we shifted position and finally installed successfully! It took about 3 hours to complete!
Anyway, if you want a durable and Small Engine Guard! For those who like it is strongly recommended.
There is a feeling that the center of gravity changes slightly because it is quite heavy so there is attention!
View detail