Reviews
Easier riding posture
Medium. The texture is good, and the riding position is easy,
Wouldn't it be better to have no Seal affixed to the product?
View detail
I wanted to make Riding Position easier.
The aluminum handlebar is a little more expensive, but the quality is better.
Also, is there anything that can be done about the Seal that is affixed when new?
I think most people would peel it off.
View detail
A familiar Position!
I came back to Motorcycle, which I gave up a long time ago, by chance.
Position out for starters! My old Hardy bar, still for sale!
Compared to the original effex handlebar that came with it.
The rise from the Handlebar Post is rapid.
Fist position doesn't change much.
Large hanging angle (my favorite)
Light
The Handlebar should be replaced to suit your body!
However, I am thankful that after more than 15 years, they are still selling this Handlebar!
View detail
HARDYBrace
It is thinner than Handlebar, so it makes a subtle statement.
It is a SMART Custom feeling.
View detail
It's high enough, but not too high.
The curved shape of the handlebar makes it taller than the riser, but it is still vertical, making it more handlebar-up type than expected when installed.
This may be good for a lower body and for raising Handlebar.
View detail
Great quality and solid crossbar
Very sturdy brace, solid. Great quality. I wish they had more sizes to offer. The clamps are good quality, but not very precise in size. It is 21mm when closed. If you want a precise installation you would have to put a piece of sandpaper over a 20-22mm round steel tube and sand this clamp a little bit. Otherwise it will not close completely on a 7/8" handlebar. I definetly recommend this brace if you need a solid one. I'm using this one for installing a windshield. View detail
Handlebar replacement to improve position
The Intermediate is the perfect height and the Riding position is perfect. View detail
Handlebar without a doubt
Unlike the cheap Xhua products, I feel that the anodized surface is good without unevenness or distortion. Also, the feel of Brace is good. View detail
HARDYHandlebar Brace is the BEST!
I chose this product because of its price, but I am satisfied with its high quality. It fits my JigSar just right, and I appreciate the stability of the handlebar, vibration reduction, aesthetics, and quality. I chose the short type, and I am glad I bought and installed the HARDY EZAttachment Handlebar Brace! It is my personal best satisfaction. I highly recommend it to everyone! View detail
Required to fix the Bar End of a Steel handle with a Large inner diameter.
[How is it used?
When we tried to attach ZETA's PROArmor Handguard Bend to KLX230R's STD Handlebar, the Bar End Adapter that comes with the PROArmor Handguard Bend was designed for use with the Smallest aluminum Handlebar. Therefore, it could not be fixed to the bar end of a steel handle with a large inner diameter (NORMAL). Therefore, we purchased the PROArmor Handguard Bend Bar End Adapter for the purpose of making it compatible with a large inner diameter.
Was the one you received as per Image?
Yes.
Was the installation difficult?
It took some force to put it on the Bar End Adapter for PROArmor Handguard.
How was your experience with it?
It matched the KLX230R's steel handle inner diameter and was secured perfectly.
[Was there anything that disappointed you?
Nothing in particular, but it would be better if the outer circumference had a non-slip finish.
[With or without Instruction Manual
No Instruction Manual is available
[Notes]
Since there is no non-slip surface on the outer circumference, it may be easy to rotate when falling down unless used with SIDE/FrontHand Guard Mount.
Opinions and requests to Manufacturer
Also develop products with non-slip finish on the outer circumference.
View detail
easy to ride
It is recommended for people who are quite Handlebar Up Type and have difficulty leaning forward, etc.
However, the handlebar is unexpectedly narrowed down, so there may be some differences in taste.
View detail
Mounted on D-TRACKER-X
MX Type? Low is installed on D-TRACKER-X.
We considered Zeta and Renthal, but decided on this one because of the price.
Details below, but generally satisfied. If it bends, I may Repeat it.
[How is it used?
Used for city driving + day touring after installation.
Was the one you received as per Image?
Color:I bought Titanium and it looks more Silver-like than I expected.
Was the installation difficult?
This was my first handlebar replacement, but I don't think there was any particular difficulty dependent on the handlebar. I had to put it on and off several times for positioning and drilling, so it might have been easier if it had a memory like Zeta's.
How was your experience with it?
The height of the Position is not that different from the OEM in terms of experience. The width is obviously wider. I am wondering if I should cut it because it is hard to pass through in the city.
I feel that the vibration is reduced as advertised by Manufacturer. (Is there an effect of the Grip that was replaced at the same time?)
[Included Parts:were they on?
Brace was there from the beginning, but Bolt was loose, so I tightened it.
[Was there anything that disappointed you?
There is a seal around the throttle side, and I wondered if I should use it as it is. I thought that I should use it as it is, but it was obvious that the movement of the throttle tube became smoother after removing the seal, so I thought it was the right decision to remove it.
I thought it would be better if it was easier to peel off the glue as it left a residue after peeling off.
View detail
It is the picture attached to the normal handle of XR230. It cannot attach, although the bar pad was also purchased. He repented [ that what was necessary was just to have purchased LONG on a one size, and ]. This place is sold off by Yahoo! A
It is the picture attached to the normal handle of XR230.
It cannot attach, although the bar pad was also purchased.
He repented [ that what was necessary was just to have purchased LONG on a one size, and ].
This place is sold off by Yahoo! Auctions, and is newly Mr. Webike, and is due to purchase LONG.
When it measures, I would like to see it exactly to the place of LONG whose MINI size is newer than the standard on it, although the bar pad purchased the MINI size of ZETA.
View detail
Anodized age fading…
This Handlebar is aluminum and lightweight.
Very good salt for touring, such as height, aperture, etc.
But due to the nature of Anodized, it will fade…
Red in particular becomes White-ish and seems to deteriorate at a faster rate.
I've been using it for many years and have no complaints about the Position, but it faded
I was in a tight Koku Pit in the
This is an exchange to Middle Bar at Fana TEC.
There was almost no change in Position and no discomfort at all from Hardy (laughs).
View detail
It is overpriced!
It was installed in order to install Navigation and ActionCamera when touring.
Unlike cheap Chinese products, the installation was done with Bolt On without any difficulty.
The Oil Temperature Meter attached to the Handlebar is visible without any problem.
View detail
Fall Prevention at Circuit
I was looking for a bar end that also serves as a slider and came across this product, which is supposed to be fixed with a rubber bulge.
Tighten as is and installation is complete!
View detail
Updated in conjunction with Smartphone Holder
Along with the new Smartphone Holder, the Handlebar Brace bar was also updated.
It's neither good nor bad, I guess.
View detail
Used in FTR223
[How is it used?
Used on FTR223.
Applications:City driving, Touring, Circuit driving
Replacement from OEMHandlebar, used for about a year.
Was the one you received as per Image?
It's just like the image, there were a few different types but the height was just right.
Was the installation difficult?
There are many parts that need to be removed, such as the handlebar body, switches, throttle, etc. It will take some time, but if you have the enthusiasm to replace the handlebar, there will be no problem.
If you want to drill a hole for the switch attachment and trim the width of the handlebar, you will need a power tool and a thread saw, which will increase the difficulty.
There is no need to extend the Clutch Cable or Throttle Wire. They can be used as is. (Shorter than the OEMHandlebar, so it can be pimped.)
How was your experience with it?
Since I did not have a dirt driving application at that time, I wanted a RoadHandlebar that was narrower and lower in height, and this product was exactly that.
The position was comfortable and I didn't get tired while touring.
The Handlebar vibration was minimal, and the stiffness of the Handlebar was moderately good.
At the time, I didn't feel any inconvenience because I didn't have a charging port or a smartphone holder attached to the Handlebar, but if I do, I think the space will be a little insufficient.
I needed a wider handlebar for the Motard race on my FTR223, so I replaced it with an Extreme bar from the same manufacturer, which is no longer available.
The wide Handlebar is much easier to use in Dirt.
For those who don't feel comfortable with the wide OEM handlebar of the FTR223, Recommendation.
[Included Parts:were they on?
Handlebar Brace
[Was there anything that disappointed you?
None in particular
Point and hang of installation
Describe the hang of the switch box attachment, not the HandlebarBody.
Positioning for the Switch box (Anti-rotation) There is a projection for
If you want to use it for secure positioning, you need to drill a hole in the HandlebarBody. If you don't drill a hole in the handlebar body, it won't physically attach.
So, if you want to install the switch box without drilling holes, you can scrape off the protrusions on the switch box.
In that case, use the Switch boxMounting Bolt (Screw) It is important to tighten the screws as tightly as possible to prevent the switch box from rotating.
I've had to scrape off the protrusions in previous Handlebar replacements, but the Switch box spins slightly and I didn't feel any problems there.
In the case of hole drilling
Electric Drill
Drill (Φ5 or Φ6)
Jig for drilling
Cle 556 (substitute for cutting oil)
It is safe to work with the
If you do not have a drilling jig, you can use the
Hammer
Punch
Make an indentation in the hole with a punch to prevent the drill from escaping.
Then I concentrated on drilling.
View detail
KSR80 Handlebar Replacement
It is a used KSR80 with 16,000Km mileage, but due to its age, there is a lot of rust on the details of the handlebar, and I decided to replace it because it is a place that is noticeable when driving. I decided to replace it.
I researched on some Reviews and selected this product which is close in dimension to OEMHandlebar.
The quality is nicely Anodized Aluminum Handlebar.
I thought it was the same size as OEM by research, but there was a slight error in aperture and height as shown in the picture. 。
When I actually installed it, I felt that the Handlebar was much lower, but since it was narrowed down, it seemed just right.
The OEM has a reinforcement bar welded together, but this product has an aluminum handlebar braze, which is very cool and I like it.
View detail
KSR80 Bar End Installation
With the Handlebar replacement, I decided to install a Bar End (OEM is Non-Penetrating).
The inner diameter of the Handlebar when attaching the Bar End can be selected from 19, 17, or 14 by using the attached parts.
The outside diameter is smaller than the ThrottleGuide, so the grip rubber can be replaced while the Bar End is still installed.
The quality of Anodized is high and it is a good product.
View detail