Reviews
Fits: HONDA CB223S, HONDA CB400SS, HONDA FTR223, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, KAWASAKI 250TR, KAWASAKI W400, KAWASAKI W650, KAWASAKI ESTRELLA, SUZUKI ST250, SUZUKI ST250 E Type, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI VOLTY, SUZUKI VOLTY, YAMAHA DRAGSTAR250, YAMAHA SR400, YAMAHA SR500, HONDA REBELUp half-wheel* with AMALThrottle
Changed from a bifurcated Wire type for independent Carburetor
I bought a battered 900SS (900SL) and am Restore.
The FCR Carburetor Body is used for the carburetor, but it is not a two-cylinder one, which is often used in car-specific kits, but independent for the front and rear cylinders.
(Independent Carburetor is designated because the radical Camshaft has teamed up with)
For Independent Carburetor, generally comes with a Car Model Kit Throttle Wire branched in the middle." is commonly used.
It is normal to have two branches and four wire ends because they are used for the open and closed sides, respectively.
That's how I used to do it.
To be precise, the Reverse Side was removed because of the poor Throttle Fee Ring, and only the Open Side was used by maintaining the smoothness with frequent maintenance.
The fee ring has been improved considerably since it is only on the open side, but there is still a branch joint in the middle of the ring, and it lacks directness.
To overcome this, we prepared this Wire to pull each Carburetor to Direct.
Wire itself is quite normal, nothing special to say.
If anything, the middle Joint is Material:I'm glad it's Stainless Steel, because I don't have to worry about Rust.
However, there is a bad part, the molding shape of Thailand is a little rough...
Of course, it is not unusable, and there is nothing wrong with using it as it is, but it is not a problem to use the bean-jam-filled wafers. (Monaka) I am concerned about the raised areas of the mesh that were formed by the matching process.
Since the thailand part may rotate slightly at the beginning of opening or just before full opening, the round thailand part will improve the fee ring at the very small opening angle.
I used File to round it out before I used it.
Even if the fee rings are not affected, the thailand coils without any snagging are easier to maintain.
Also, there is no coated tube inside the Outer tube.
It is a Wire configuration with no features whatsoever, consisting of Spiral Tubes made of the old-fashioned Gold genus.
So the first lubrication is a Large thing.
Without oil, the feel will be rough, and with high viscosity oil, it will be sluggish.
On an FCR Carburetor Body with the Reverse Side removed like mine, it is fatal and life-threatening not to be able to spackle back.
This is not limited to this Wire, but try it often before lubricating with the best Oil.
View detail
very satisfied
There was a situation where the clutch cable suddenly broke, so I ordered it in a hurry, and the delivery was really fast.
The product is also very satisfactory. If you need a longer extension clutch cable by lifting the handlebars up, you can purchase it.
You will use it very satisfactorily. I am very satisfied with the speed of delivery of the product and the build quality of the product ----------------------------------- ----------------------- Suddenly, the clutch cable was cut off and I ordered it in a hurry, but the delivery is really fast. The product is also very satisfactory. If you need to buy a longer an extension clutch cable with a handlebar, you can buy it. You will use it very satisfactorily. Powered by Google Translator
View detail
Beautiful laser cut
I am building a custom vehicle with a Motorcycle called Yamaha's XV750E.
We are in the process of completely rebuilding the seat rail.
We are working with steel welding, but it is very time consuming to start cutting out even the smallest brackets.
Also, since we cut them out by hand, we cannot by any means make "exactly the same thing".
The savior in this situation is the Weld Bracket.
2%er also offers a similar Weld Bracket, but this time I went with GOODS' because I liked the Steel and the dimensions were just right.
We do not have a TIG welding environment, so it is inevitably Steel.
There is a lot of welding with Pipe, but I think the thickness is just right and there is little chance of failure.
Since they are still too thin, they may have holes or be distorted if they are too thin together;
This time, thanks to the WELD system parts by GOODS, we were able to shorten the work time considerably.
I would use it again next time.
View detail
Fits: YAMAHA XS-1, YAMAHA XS650, YAMAHA XS-1, YAMAHA TX650, Others , YAMAHA XS650
Diversion to XV750E
It is for YamahaXS650, but I used it to convert XV750E to 520.
It could be used for TX650 and others.
I believe the same modification would also work for the XV1000TR1.
I really wanted to convert my original 630Chain XV750E to 520Chain, so I have been looking for a Sprocket that I could use.
I was thinking that I had no choice but to special order it from XAM……, but it turned out that the Spline shape is common with XS650.
In addition, 520for ConversionSprocket was sold at a discount.
This Maniac product was in stock at GOODS and was delivered to me in 3 days.
The XS650 is a center nut type, while the XV750E is a type that is fixed with a fixing plate.
In other words, you must drill Bolt holes to fix the Fixing plate.
Naturally, the front sprocket is hardened gold, so it is impossible to drill a hole in it with a half-assed drill bit.
This time, I bought a carbide Bit together and tried to drill holes.
Using a ball machine, we gradually expanded from 1.5mm and successfully drilled a 5.5mm hole, which is a pre-drilled hole for an M6 bolt.
However, the Screw cut from there was Large strange, and I really had a hard time because of the hardness of the Material as well as the shape that was difficult to fix.
We managed to get a Tap up on Beauty, but it cost us several carbide Bits and 1 pc of Tap.
The results are shown in the image.
However, because the thickness of the Sprocket itself is different, it is offset outward by about 5mm.
Conversely, if you create a Washer, Spacer, etc., you can move the Chain line freely to some extent, so it is the best Sprocket, depending on how you think about it.
View detail
I appreciate the low price, high quality, and the fact that I can buy from 1pc.!
[How is it used?
I purchased the Bullet Type Terminal when I needed to replace the Blinker on my old car, Yong FourType.
Was the one you received as per Image?
It was more solid than Image. It is totally different from the one from a hundred-odd different places.
Was the installation difficult?
With Electric Works Pliers, crimping is easy.
How was your experience with it?
So far, the contact is energized and usable without any defects at all.
[Included Parts:were they on?
Nothing.
[Was there anything that disappointed you?
Not particularly
I'm glad I bought it because it's the perfect size. I think it's good to buy it as an adjustment when you are almost to the Gold amount for free shipping.
View detail
Processed to VM38.
I bought this for a YamahaXV750E with two VM38Carburetors.
Quantity since it is a 2-stack:I bought 2pc
I once bought a 2-sided Cable for another car model, but it was not long enough and the Piece of the 2-sided part was not enough φ38Carburetor could not be opened.
The VMcarburetor is a type that directly pulls up the throttle valve, so the wire stopper is a traditional gourd shape.
There are some available, such as for SUPER CUB, but I was concerned because the lengths do not match and they seem to be very poor.
Surprisingly, I could not find one for Large size vehicles, and after much searching, I found that GOODS sells one for SR400 and purchased it.
They said it was forφ38Carburetor, but it is only for AMAL364TypeThrottle holder, so it needed Outer processing.
In my case, I have a two-stack, so Tommaselli's Quantity:2pc pull Throttle is used.
It is a pull×2Type instead of a pull/reverse, which is a bit unusual in modern times.
The Inner cable was not long enough at all, so we cut the Outer by 7cm.
The Crimp in the end section was also ported.
Thailandco used Active's products, but since Screw alone seemed to fall out, Solder was poured to fix it in place.
I was able to install it successfully, and since it can be adjusted in the middle of Cable, it can be tuned out.
View detail
Fits: YAMAHA V-MAX 1200, YAMAHA SR400, YAMAHA SR500, YAMAHA XT500, YAMAHA YB-1
I always use it for SR400.
No exhaust leaks and no complaints about quality. View detail
Dress-up
I wanted to replace the OEM RedCap with a Vintage plug cap.
Terminal nut was needed on the Plug side.
View detail
OEM same etc.
I decided to purchase the Decompression cable as well. View detail
Costa, good light!
The Shovel's low beam stopped working, so I replaced it with this Headlight Bulb.
Shovel has a lot of vibration, so I thought that might be the cause.
HeadlightBody is using Other Brand Product.
It was slightly slimmer than the existing Valve.
It is good to stock two or three of them because it is cosy.
It doesn't reduce vibration, so I'll keep it in my Tool Bag.
The image is of an existing Valve.
View detail
Replace because it's getting tired
I bought this type to replace the Power Filter which was installed when I bought the car. The intake air seems to have improved. View detail
Change from Straight Type
Straight type was installed when I bought the car, but it was contacting with the frame and wiring, so I changed to this Taper type. View detail
Convenient to sell by 1pc. unit
The ability to buy by the 1pc. unit is revolutionary, and it's convenient to buy as much as you need.
The packaging is also easy to handle as there is no extra paper Tag or Stapler.
It's also nice to pull out and have a moderate Click feel.
GoldPlating seems to have good conductivity.
View detail
Sufficient performance
I bought it as an OEM replacement.
It seems to be slightly brighter than the OEM.
It's been two years since the replacement and it's working fine.
Each part is well finished and can be replaced in Smooth.
View detail
Available from 1pc
I'm satisfied with Large because I can buy only the parts I need for the parts I rarely use
The terminal and the coupler were not softer than OEM parts because they were new It's also securely installed
It was more than enough
View detail
GOOD
I used it on Honda's MAGNA50
The Brake lever and Holder on the Right Side are connected to the SPTakegawa Since I changed to Standard Type, I changed the Clutch Side as well
OldHondaStyleLever of GOODS is, as the product name suggests, an old-fashioned Honda type
It's a Standard that couldn't be better
Both the Holder and Lever were matte black
Brake lever and Holder of SPTakegawa have Luster and Black color So it's a bit of a failure lol
Well, I think it will shine if you polish it up, and that's exactly what the Brake lever has been doing from the beginning with GOODS' I should have bought an OldHondaStyleLever
The cable adjuster is probably made by Brass
I'm sure that Holder and Lever, which Mr. Minimoto sells, are also Cable The adjuster was made by Brass, so maybe, just maybe, lol
However, the mirror mount of the Minimoto's products is M8, so I don't want to do it this time We're here
The brake lever of SPTakegawa was M10, so I used this one to match it I chose
In addition, the Thai part of Cable is a Large type, so you can use it as I think MONKEYOEM's Cable, for example, is too loose
Buy a Clutch Cable for an external Lever such as SPTakegawa
Accuracy and texture are both good
I don't know how long it will last since I just put it on, but it's a rickety OEM that's been rattling around for a good 10 years It feels better than Product
View detail
What you need
A part that many people will need during each Holder replacement that the company sells
Seems like it could be sold by more manufacturers
The product itself fit into the hole with no problems
View detail
Good
My light box wire is damage, so I cut that and ember this terminal, now the light box is repaired and can be use. It is good condition and perfect. View detail
For OEM Switch processing
Headlight, Horn, Blinker's Switch was this I want to use Passing, so I'm going to rebuild Wiring for Switch here View detail
Clutch switch as Can Sera
I was wondering if the 3PCoupler can be used with the Clutch switch for other models if it is a 110-inch model I think The only drawback is that I wish there was Black It looks like it's going to stand out unless I wrap it around with BlackVinyl Tape. 1 you can buy it from pc. so I bought it on an errand while I was at it for free shipping View detail