Reviews
just barely
Depending on how you put it in, it can hold a SHOEI x14 M and a GT AIR2 S, but if you make a mistake, it won't fit.
I was uncertain, so I went to the store to check it out.
View detail
Storage has increased all at once, making it more convenient.
[How is it used?
It is being used on a NMAX 155.
Carrier is made by Y's Gear.
I purchased this product because I felt that the storage under the seat was not enough to hold a full face helmet and that the amount of storage was not enough.
Was the one you received as per Image?
I bought the 33L because I didn't like the large size of the box while aiming for more storage, but it is surprisingly compact.
The rear view after installation is also comfortable, and since it fits within the width of the handlebar, there is no problem at all when slipping through.
Was the installation difficult?
I installed Base on Carrier made by Y's Gear, but I struggled a little because I could not decide on the Bolt to install it in a good place.
I was able to install it without any wobble, but I didn't want it to fall off, so I used Tie Wrap to secure it in two additional places.
How was your experience with it?
The feel is great, more versatile than expected.
The square shape allows for a wide storage width and prevents the creation of dead space.
The lid closes with room to accommodate a full face helmet (SHOEI GT-Air II with B-COM).
Gloves can be stored together.
On top of that, it can be stored under the Seat, which I think is a great combination with the Scooter.
A 6-can pack of beer plus several 500ml cans can fit in the bag, so it can be used for after-work shopping.
I have used it in the rain and it is convenient for my daily commute with no flooding. It is very reliable.
[Included Parts:were they on?
It came with everything without any problems.
[Was there anything that disappointed you?
I don't know if I can say this is disappointing, but it is subtly difficult to tell if the lid is properly closed once opened.
It is not closed by just pushing it in, "Snap" If a small sound is heard, it is OK.
Check after closing the lid is essential, as the key can be pulled out even if it is not tightly closed.
[Notes]
Please pay attention to Bolt tightening when installing Base.
If you want to close Firmly, the Base will lose and distort.
View detail
It could be used for OEM Carrier Plate.
I was looking for replacement parts for my Honda OEMCarrier Plate anti-vibration Rubber stopper that had deteriorated and came across this Parts (Replacement Rubber stopper for GIVI M9A/B), which I found to be a collaboration product with GIVI.
It went on the HondaOEMCarrier Plate with no problems at all (at my own risk).
I attached the rubber to the plastic base and then attached it to the carrier plate, but it was quite large and strange to attach the rubber to the plastic base. I had to pull it very hard to get it to fit.
View detail
Flat cushioning material
The bottom is flattened and the Material is soft, so it replaces cushioning material and is gentle to luggage.
Since the matte capacity is reduced, it can be removed depending on the application.
View detail
Aftermarket parts are very helpful.
Purchased for Repair as Rust came out.
These fine Aftermarket parts are really helpful.
I hope they will continue to do so.
View detail
Easy to use
I installed it on a CT125 and it is large enough to fit one full face. The lock is a little bit hard to do, but I think I will get used to it in time. View detail
Nut mold on the back side sticks
I have been using Tank Lock and wanted to continue to use it.
The installation itself can be done by anyone since all you have to do is tighten the screws.
However, if you leave it on, you may not have to worry about it, but when you replace the air filter for maintenance, for example, you will have to open the tank cover, and you will have to remove this product every time to remove the tank cover.
Then I took it off and found that the Nut on the back of the part that holds the Bag in place was hitting the Center cover and molding it.
The precision of the workmanship may not be good, and when the bracket was applied to the tank cap, it was not bent enough and the bag attachment part was in a floating state.
It is supported by the Rubber foot, but the Rubber foot is not high enough or it is floating, and when the Bag is placed on it and the Rubber foot touches the Center cover, the Nut on the back side touches the Cover.
If you don't think about mold adhesion and maintenance, there is nothing wrong with normal use.
View detail
I like the squares.
I commute to work on my motorcycle, so my first requirement was to be able to store my helmet.
Unlike other MODELs, it is a square design, so there is plenty of room in the SPACE for rain gear, etc., in addition to the Helmet.
It is very convenient to put things bought at SUPER or Convenience!
View detail
easy to use
[How is it used?
I was looking for a Top case in a size that can be used not only for shopping but also for overnight stay to attach to MT-25.
This was the first time for me to purchase a top case, but I chose this product because of its price and size.
Was the one you received as per Image?
I knew it would be huge, but the product that actually arrived was even bigger than I imagined. (Lol)
Was the installation difficult?
It is very good for GIVI's SRVFitting because it can be installed in seconds.
It is easy to install and remove and requires unlocking, so it is very well thought out for both convenience and security.
How was your experience with it?
The loading capacity is perfect.
The square shape allows for quite a lot of stuff to be put in.
A full face helmet can also fit in the vertical orientation, so you don't need to use a helmet holder if your luggage is small. If you do not have much luggage, you do not need to use a helmet holder.
It is also good that the structure is key lock-in-proof, so there is no need to worry about such things.
[Included Parts:were they on?
In addition to the top case, the Mono-lock base and other necessary items for installation are included.
I am using SRVFitting of the same Brand, so I do not need Universal's Mono-lock base in that case.
[Was there anything that disappointed you?
Not particularly
【Review】
It has a sufficient capacity, with key, and is easy to attach and detach.
It made shopping easier.
View detail
Appearance highest
I just took delivery of my C125 and installed it right away. I was not sure whether to use a Chinese AluminumBox or not, but I went out on a limb and bought a Givi Aluminum Box. 42L would have been sufficient for the C125, but I think I could have gone with one size larger. I like the look and parenthesis. The base is required for installation. View detail
I wonder if it is just right in terms of Large size!
I purchased B33N at the same time I purchased ADV160.
Top case is a must, as it seems almost impossible to Helmet in under the Seat of ADV!
However, I don't plan to can two or something like that, so I decided on this size because it is OK as long as I can put a helmet in and Rainwear can fit in it.
The capacity is not a problem at all, and the ease of use is convenient to say the least!
Just one point ….
I thought RedReflector was better than Smoke Reflector…;
The part I regret a bit is the Minus of satisfaction….
View detail
Required for installation of GIVIAluminumMonokey top case
I purchased this product because I needed it to install a GIVIAluminumMonokey top case. The price is high, but it is a reliable brand. View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
Use with Fender Eliminator Kit
[How is it used?
I purchased this product to install GIVI's Top case on my MT-25 which I use for long trips and shopping.
There are many options for carriers, but we chose this product because we wanted to attach a GIVI Case and were a little concerned about the strength of the Grab Bar alone.
Was the one you received as per Image?
Bolt and Bracketetc. were included as shown in the pictures without any shortage.
Was the installation difficult?
It takes considerably longer to install than the Carrier with Grab Bar installation.
There is an installation instruction manual, but the Large section is explained in letters, so it was very difficult to understand MinusPoint.
Also, although the kit is not designed to be used in conjunction with the Fender Eliminator Kit, it was possible to install it in conjunction with DAYTONA's Fender Eliminator Kit at my own risk.
There is no interference with the Blinker, although it is necessary to place a 3mm spacer between this product and the Fender Eliminator Kit.
How was your experience with it?
The Tandem Footpeg and the Fender section are fixed in 6 places in total, so they are fixed quite firm.
It is quite stable, with no interference with the vehicle body or chatter.
It made shopping more convenient.
However, due to the fact that it is fixed with a Tandem Footpeg, KIJIMA's Helmet Holder cannot be used together.
[Included Parts:were they on?
All necessary items other than tools such as mounting Bolt, Nut, Bracket, etc. are included in the package.
[Was there anything that disappointed you?
As I mentioned above, the installation instructions are very confusing.
It is not enough to have a diagram like an assembled piece of furniture, even if it is explained in words....
In addition, the size of the cap to be attached to the bolt on the SIDE was not correct, so it was necessary to file it down to a size that would fit.
【Review】
Firmly fixed to the vehicle body, it makes shopping and other activities very convenient.
The holes were well aligned and there was no need for any special modifications afterward.
I would like to see a little more work done on the instructions, as the product was good.
View detail
It was Exactly in C125.
C125 was delivered and I immediately purchased and installed it! 。 I was not sure whether to go for the Chinese AluminumBox or the GIViAluminum, but I went for the GIViAluminum. 42L was enough for my C125, but I think I can go one size up. I like the look and parenthesis. The Base is required for installation. View detail
I installed it on a c125.
I purchased and installed the GIVIAluminumMonokey top case on my C125. The installation was easy and took about 30 minutes.
The top case does not wobble and is perfect.
View detail
Inexpensive Pannier case
The Pannier case is not made of the sturdy gold material, but the same material as a standard top box. The load capacity is 46 liters for both, which is not much, but if you want to install a Pannier at a low price, this is the size for you. However, this size can be installed for only 50,000 to 60,000 including the bracket. Well, the Side Back can be installed at about half the price. LOL! I have a NC700X with a Fuel Tank under the Rear Sets, so with the Seat Bag, I had to remove it every time, which was inconvenient, so I went with the Pannier.
I haven't fallen over it yet, but it could crack if all the weight is on it at once, and the Bracket would probably be warped.
Still, the load's
The good thing about Pannier is that it can be loaded without losing its shape. The rated load capacity is 10 kg for both. I have not loaded that much.
No, but...
View detail
Fits: HONDA NC700S, HONDA NC700X, HONDA NC750S, HONDA NC750X
For Pannier mounting
I purchased this product as a car model specific to install the Pannier case.
It is a givi for better or worse, so I think the texture etc. is like this.
Large Pannier molds cannot be fitted, but they are sufficient for my needs.
I am satisfied
There is no rattling or deflection when the Pannier is installed.
As long as you don't fall over, you should be fine.
The installation took less than 30 minutes for a large body.
It is a bit tedious to remove the Seat, but technically it is an easy part.
View detail
Fits: HONDA NC700S, HONDA NC700S, HONDA NC700S, HONDA NC700S, HONDA NC700X, HONDA NC700X, HONDA NC700X, HONDA NC700X, HONDA NC700X, HONDA NC700X, HONDA NC700S, HONDA NC700S, HONDA NC700X, HONDA NC700X, HONDA NC700X
For PL1111
If you are going to add a top box, this component is not necessary,
I only have Pannier case so I needed this part.
It is still a GIVI component, so the price is high.
It is quite thick and does not seem to flex or bend.
Without this part, the Pannier holder cannot be installed,
It can't be helped.
View detail
Easy to use.
It is useful because it is light in Monokey.
When extended, it is large enough to hold a Shoei X-14.
The reason for the ??1 on it,
The lock Number of the Dial lock is
This is because there are times when one Gaps when locking the door.
I can no longer open it.
View detail
Fits: Others E26NCD, Others E26X, Others E26N, Others E300N2, Others E30TN, Others E42NS, Others E33, Others E300
As a spare because it breaks regularly.
We use Boxes in multiple vehicles and change Boxes about 5 times a month. At that frequency, it took about 4 years to crack.
The Box will not come off if broken, but this part will fly off when the lid is unlocked, so I buy one and keep it as a Spare if it is broken.
It is inexpensive and inconvenient if it breaks, so I will buy it, but it is sad that the price has gone up so much.
View detail