Reviews
![Fitting for Monorack [7707FZ]](https://img.webike-cdn.net/catalogue/images/91664/18890_01_TS.jpg)
Mounted on 250DUKE
I was thinking of adding a Carrier in terms of style, but I thought it could be a substitute for a Carrier without a Top case, and also I thought it would be too much of a fussy thing, but I guess it is not so much once you get used to it.
It went on the 250DUKE with no problem, as it should.
When installing, there should be no problem if the entire unit is temporarily assembled while tightening it at the end.
However, it can't be helped that it is Steel, but I think GIVI's Bracket is quite prone to rust in the smallest details.
View detail
![Top Case Fitting for Monolock [SR1191]](https://img.webike-cdn.net/catalogue/images/104416/1_165032128479988800_m_9wdoa_l_TS.jpg)
Fits: HONDA CRF250L, HONDA CRF250L〈S, HONDA CRF250 RALLY, HONDA CRF250 RALLY〈S
Installation is Large size.
The style after installation on the motorcycle is not too assertive and is good for parenthesis.
The Carrier is not noticeable because it is dedicated to GIVIMono-lock case, and it is nice to be able to install it low.
Installation was a challenge.
It is difficult to explain, but when the Seat is removed and installed, the Seat cannot be put back on. Also, if you leave the Seat in place, the Carrier will not fit. The product is so precise that there is no room at all. I had to push it in a little too hard. I think this may be because the Seat is wider on the RALLY50.
View detail
![Fitting for Monorack [6412FZ]](https://img.webike-cdn.net/catalogue/images/91664/98789_01_TS.jpg)
STREET TRIPLE765rs 2023 type
Although it is listed as compatible up to the 2020 model year, it can also be attached to the 2023 model year in the same way.
Since there is no English version of the instruction manual, we worked while looking at the translated site in some places.
The instructions for drilling the holes appear twice, but the 8.5mm holes are drilled while the parts to be drilled are still attached to the vehicle body for alignment.
Then, after removing the Parts, there is the work of drilling a 19mm large hole.
The drawback is that we do not have a 19mm diameter Drill and have to have an assortment of tools.
Once installed, I think the strength will not be a problem since it is Firmly in place.
View detail
It's expensive
It is expensive, but it is GIVI and can be installed without any problems. I would give it 5 stars if the price was less than 20,000 yen.
Well, I couldn't find any other Manufacturer's stuff, so I had no choice.
By the way, the box is not a GIVE.
View detail
Fits: SUZUKI V-STROM650 ABS, SUZUKI V-STROM1000 ABS, SUZUKI V-STROM1000XT ABS, SUZUKI V-STROM650XT ABS, SUZUKI DL1000 V-STROM650
That's the exclusive product
Installation is a bit confusing, but the car model Exclusive Design allows for a secure installation. View detail
Rear Sets... (>_<)
Tank Lock (→Tank Bag.) I wanted to put it on the Tank, but my DL1000 V-STROM250SX has a (It was for Jig Sir.) It didn't land well, so I got myself together and moved it to Rear Sets.
I never arrived at the Order-made, but I did manage to get within the Limit of attachment to give it an acceptable score. (^-^) /
I would like to use it as a CameraBack. It is my personal opinion, but it is not bad.
View detail
Easylock BF11
I think the price is too high, even if it is unavoidable due to the model-specific nature of the product. View detail
![Pannier Holder [PLX3101]](https://img.webike-cdn.net/catalogue/images/91664/90534_01_TS.jpg)
Pannier holders are nice.
I purchased the Pannier case in addition to the Top Case and was very impressed with the Holder, which is an exact match for my car. I was very impressed with the Holder, and the installation position is also very close to the Exhaust System.
in a nice salty way. [Color] ClearQuantity:Pair (for Left and Right) The sense of balance was good.
View detail
Nut mold on the back side sticks
I have been using Tank Lock and wanted to continue to use it.
The installation itself can be done by anyone since all you have to do is tighten the screws.
However, if you leave it on, you may not have to worry about it, but when you replace the air filter for maintenance, for example, you will have to open the tank cover, and you will have to remove this product every time to remove the tank cover.
Then I took it off and found that the Nut on the back of the part that holds the Bag in place was hitting the Center cover and molding it.
The precision of the workmanship may not be good, and when the bracket was applied to the tank cap, it was not bent enough and the bag attachment part was in a floating state.
It is supported by the Rubber foot, but the Rubber foot is not high enough or it is floating, and when the Bag is placed on it and the Rubber foot touches the Center cover, the Nut on the back side touches the Cover.
If you don't think about mold adhesion and maintenance, there is nothing wrong with normal use.
View detail
![Fitting for Mono Rack [436F]](https://img.webike-cdn.net/catalogue/11160/fitting_image-1_TS.jpg)
Easy due to car model-specific
The scale to make the bracket parallel was partially obscured. Therefore, we had no choice but to install the brackets by feel. View detail
![Plate Set For MONOLOCK Base [MM] MONORACK](https://img.webike-cdn.net/catalogue/daypic140709/90174_1_l_TS.jpg)
Fits: HONDA CBR1100XX SUPERBLACKBIRD, HONDA CBR1000F, HONDA CBR1000F, HONDA CBR1000F, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB750
Need to cut BALI
I installed the Bracket and this Base, but there was some BALI and I had to shave it off with File. I am satisfied with the Minus but the rest is Large. View detail
![MONOLOCK Base [M5M] for FZ Series](https://img.webike-cdn.net/catalogue/11160/60145_1_TS.jpg)
Fits: HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CBF1000 06, HONDA CBF1000 07, HONDA CBF1000 08, HONDA CBF1000 09, HONDA CBF1000 10, HONDA CBF1000 11, HONDA CBF1000 12, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500
GIVI GIVI Mono-lock base
Was the one you received as per Image?
Same as in the picture.
How was your experience with it?
It is formed of resin but is rigid.
Because of the thickness of the resin, there is no feeling of easy twisting at all.
Purchased to use Mono Lock Case B37 Series.
Quantity:Set and removal is also very easy.
Excellent stability while driving.
The GIVI Logo on the SIDE is also good as one point because it is an accent.
The reverse side is slightly chamfered, and if you touch the edge of the reverse side when washing your car, you will get a sharp cut.
[Points to note]
When this Body is installed, it tilts depending on how the Bracket is attached.
To be installed only after being firmly aligned in height for Bracket dependence.
The rubber stopper that came with the box had a gap between the box and the stopper.
Box bounces around while running, making a popping sound.
This can be solved by changing to a 9.5mm Rubber stopper, which can be purchased from Spare Parts.
It would be a good idea to change it from the beginning.
There are no obstacles during installation.
How did it compare to other products?
I used to use MP60N UniversalPlate, but the rigidity is completely different.
UniversalPlate is also screwed down during installation, which inevitably results in torsion.
This product is solid, as it is a dedicated product.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
I think you should also enclose a 9.5mm Rubber stopper from the beginning.
View detail
![Fitting [PL4121]](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0309/24082106_20220829100913936_TS.jpg)
Satisfied?
Not installed yet.
I just looked at Parts and it was beautifully done.
View detail
New car installation
When I purchased tracer9GT, I asked the installation store to send it directly to me.
52Liter bock installed.
View detail
![Fitting for Mono-lock [3111FZ]](https://img.webike-cdn.net/catalogue/images/91664/1_148460405673614400_m_z5dm8_l_TS.jpg)
first purchase
It took a little time because of the Wiring process required. View detail
![Mono-Key Base [M7] for FZ Series](https://img.webike-cdn.net/catalogue/11098/m7-91332_TS.jpg)
Fits: APRILIA SHIVER 750, APRILIA SRV850, BMW C650 Sport, DUCATI MONSTER 1100, DUCATI MONSTER696, DUCATI MONSTER796, HONDA CBF1000, HONDA CBF500, HONDA CBF600 N, HONDA CBF600S, HONDA CBR600F, HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin, HONDA VFR1200F, HONDA VFR800, HONDA VFR800, HONDA VFR800F, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ER-6n
Made by GIVI for peace of mind.
Used on CB400, HORNET and PCX.
I laughed here because of the design of the look of the Top case when it is removed.
Personally, I think Parenthesis is good.
It is more expensive than other cheaper products, but it is robustly built.
As a base, it has many holes and cavities, so it can be universally installed depending on the device.
If you are interested in installing a Large-format Case and also care about its appearance, this is a product that we recommend.
View detail
![Pannier Holder [PL5126]](https://img.webike-cdn.net/catalogue/images/91664/98965_01_TS.jpg)
Required some modification for installation.
After ordering, I waited about 2 months for it to arrive.
The original arrival schedule was extended, but we ended up arriving as scheduled.
I thought the product PL5126 could be accepted for all years of BMW current G310GS, but the Instruction Manual in the packet stated that it is compatible with 2017-2019 BMW G310GS.
When assembled on a G310GS manufactured in 2021, the Bolt position of the Arm that attaches to the Right SideFootrest did not match.
I considered returning it. Cancellation, returns, and exchanges are not possible after an order has been received. So, we managed to install it by cutting and expanding the Bolt hole.
Also, when relocating the Rear Blinker, the Right SideBlinker's Wiring had to be shortened and extended.
It could not be pontooned easily.
View detail
Helmet holder is the key
The NinjaH2SX/SE has a helmet holder...
I can see how this product would be exempt from the basic application, lol.
For International Model? does not have a helmet holder or is it possible to install it according to the application of GIVI headquarters.
Although I trusted this information and bought it, I had a hard time removing the helmet holder first (^^ゞ).
One wayType Screw and the Screw that attaches to it are blindfolded, so it can be removed by force and finally installed.
I am using Fender Eliminator, so depending on the Kit, it may be necessary to change the Blinker position, etc.
View detail
Spring BigSale
When I searched webike to get the necessary parts for my G310GS before delivery, I found that the Spring Big Sale was being held.
I had not planned to install the Pannier case at this time, but I was attracted by the 25% off and thought it would be a Guard for the car body without the Pannier case installed.
Since the product is on order, it will be a while before it is delivered, so we would like to consider installing a Pannier case or Side Back.
View detail
It can be used for NINJAH2 SX.
I bought this because I wanted to try the XS320.
If you use the collar that is attached to the BF35 for the original NINJAH2 SX, it will not attach as it is.
I think it would get there if I shaved the inside of the Flange a bit, but if it would get there the same way as the VERSYS, I don't think it would be a problem, so I wore it without using it.
So just buy an XS320 and a BF26 for VERSYS.
View detail