Reviews
Quality control or packaging issues
Installation is Level, which is fine for Beginner.
No special problems with the feel of the product.
However, there is a relatively noticeable scratch on the base plate section….
Was the shipping check lax, or was the packaging messy and damaged in transit?
It's not a practical problem, but ….
The mood is lowered by the relatively expensive components.
View detail
![Fitting for Monorack [5137FZ]](https://img.webike-cdn.net/catalogue/images/91664/21033_01_TS.jpg)
RearCarrierQuantity:Pair (for Left and Right) The bracket does not align with the base mounting holes on the top case.
I purchased this product to install GIVI's Mono-lock case 47 on my F900XR. I would like to comment on the installation process and the state of use.
(1) RearCarrier's Bracket is LeftOnly Right and Quantity:Pair (for Left and Right) Since there is no Bracket to link the Quantity:Pair (for Left and Right) There is some difficulty in determining the horizontal state of the Bracket.
The ?Instruction Manual is somewhat confusing.Quantity:Pair (for Left and Right) It would be good if the distinction between Bracket and the reverse side is clearly indicated.
(3) Base plate hole and quantity on the bottom of Top case:Pair (for Left and Right) Bracket holes are FrontQuantity:Pair (for Left and Right) Two of them fit, but not the Rear. However, the Rear hole was not inserted, and since the Bolt hole was shifted from the normal position, I am not sure about its strength.
Also, the position cannot be adjusted back and forth.
?There are no strength or other problems so far in using Top case, but the position of Top case is quite high.
I would like to see the Bracket extending to the rear of the vehicle reshaped so that it is lower. Also, the Top case is slightly further rearward than the rear wheels.
View detail
![MONOLOCK Base [M5M] for FZ Series](https://img.webike-cdn.net/catalogue/11160/60145_1_TS.jpg)
Fits: HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CBF1000 06, HONDA CBF1000 07, HONDA CBF1000 08, HONDA CBF1000 09, HONDA CBF1000 10, HONDA CBF1000 11, HONDA CBF1000 12, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500
Exclusive goods
I feel that it does not have to be a dedicated product. View detail
![Fitting For Mono Rack [359FZ]](https://global.webike-cdn.net/photo/article/30/1285509662530L.jpg)
Although the cut of a rear cowl is required to attach to a phasor, Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm, Since it appears in the instruction manual and the perforated line is contained also in the cowl side
Although the cut of a rear cowl is required to attach to a phasor,
Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm,
Since it appears in the instruction manual and the perforated line is contained also in the cowl side from the beginning perfectly, the place to cut for true -, [ easy ]
That there are two stars (although looked in, to the extent that it does not understand) which are not known by any means if it does not look in from the bottom even if cutting [ which wages had as I have you attach in a store / which is not ] temporarily goes wrong,
Although the drilling accuracy of the attached parts made from aluminum having been open at the place bad shifted for a while and these parts become a form inserted in the frame by the side of a car body, it is the point which only a few had to correct with the stick file greatly (it is aluminum, it deletes immediately and can correct).
View detail