Reviews
![Tank Lock [MT505]](https://img.webike-cdn.net/catalogue/images/27457/94562_TS.jpg)
Replaced the company's XS319
We were looking for a replacement for the company's XS319 Fastener, which we have been using for several years, due to damage to the Fastener.
Main compartment holds a smartphone (Pixel7pro), a bifold Wallet, an electronic Cigarette in a Case, and Toilet paper instead of Pocket tissue
With the XS319, I had difficulty handling the Cable when charging my phone, but this is not a problem with this product!
The Pixel7pro does not fit into the smartphone storage pocket on the back of the lid because it is not wide enough.
I think the width of Xperia1II used for Navigation is the limit (although it is slightly long).
View detail
Helmet and rain gear
I had been using a 26-liter round top case, but I felt that the round shape offered less storage space, so I purchased this 33-liter square top case.
Tour cross3 with Visor will fit enough +α to hold at least rain gear.
It is easy to lock the door without a key, but you have to be careful with the marker.
View detail
![[Repair Parts] Universal Base Repair Parts](https://img.webike-cdn.net/catalogue/images/129441/31335_TS.jpg)
Those who use one Case for multiple car models.
I purchased this product to convert a GIVI Mono-lock case to another vehicle. It is easy to install and can be installed in most carriers without any modification. The price is also inexpensive, so I think it is the best choice. View detail
![Rear Box [B32NB]](https://img.webike-cdn.net/catalogue/images/75563/16965_TS.jpg)
I liked it.
Installation and removal are excellent.
Is the rigidity a little weak, perhaps because it is designed to be lightweight?
View detail
Large doubles as Small
Boxes used so far
Mono-lock case [E43NTL-ADV]
It is good because there is plenty of room in terms of capacity, but the closing operation is cumbersome until you get used to it.
It was Stress every time, every time.
Mono-lock case [B32NB-ADV]
The closing motion was easy as I just closed the lid.
Top box 35L, compatible with Honda OEM and Smart key
Although Merit is that only one Smart key is needed.
The inside of the box has a lot of protruding parts, and perhaps because of its shape, it is necessary to consider the direction of the Helmet when storing it.
I had only used it for 2 months, but Stress was more Large.
That's where I found this B45+ this time.
Well, certainly Large
I think it looks the worst from behind.
But I think the security of being able to fit a lot of luggage and the lack of Stress when using it is good.
Base plate is made of Wide (Sold separately) I feel more secure now that I have changed to
I don't know if it's because it's still new, but the Hinge part is stiff.
Much thinner and chubbier insoles than previous GIVI product insoles
Those are the two things I'm not happy about.
My request to Manufacturer would be to add a Pocket or something to hold the included Net in the corner or edge of the lid side!
View detail
![Mono-lock Case [E43NTLD]](https://img.webike-cdn.net/catalogue/images/105397/95339_TS.jpg)
Large also means Small Yes!
I have recently been commuting on my motorcycle more and more and was feeling that my old B32 was running out of capacity, so I bought this E43 just in time for the start of Webig's sale at Timing.
It arrived as fast as possible because it was in stock, so I installed it on DJEBEL right away.
I am very satisfied with the capacity, which is sufficient for commuting.
It is wider than the B32, so it feels larger now, but I think you will get used to the larger size as you start using it.
It would be great if it came with a non-slip rug on the bottom of the interior, but maybe I'm being a bit greedy? LOL!
View detail
45Liter is Large capacity
When I received the package, I was surprised at how large it was, but not so much when I installed it on the car body.
Installation is simply by attaching the Base to the Carrier.
DL1000 V-STROM250SX does not use UniversalBracket because of the mounting holes in the Carrier. The supplied Bolt was a little too long for the UniversalBolt, M6*20mm should be fine.
OGK GEOSYS is also large enough to close without laying down, and can still fit a helmet, rain coat, and gloves.
View detail
First Top case
It took a little time to position the base plate, but the installation itself was on a Level. View detail
![[Replacement Parts] Inner Mat for B32 Series [PB32N]](https://img.webike-cdn.net/catalogue/images/75563/16011.PT01_TS.jpg)
Exclusive shape is stunning, price is high
Although the complicated cut shape is unique to OEM, I think the texture of the matte itself is quite similar to that of OEM.
I wished the price was another 1,000 yen lower.
View detail
![[Repair Parts] M2X12CSK Tapping Screw MP60/MP70](https://img.webike-cdn.net/catalogue/images/107316/24267_TS.jpg)
Purchased for Repair because it was rusted.
I got this screw from a friend who gave me a GIVI box… I took it apart and found that it was rusty and would come apart if I removed the rust. I am glad to be able to order such a minor part from you! View detail
Satisfaction with Largeness
I am satisfied with it because I can put large items in it. However, if I put a helmet and a jacket in it, I can't put them in.
The lock works without a key, so be careful not to put your motorcycle key inside!
View detail
![Mono Lock Case [E43NTL-ADV]](https://img.webike-cdn.net/catalogue/images/32552/95342_01_TS.jpg)
Installation requires ingenuity.
The included Mono-lockUniversalWIDEBase did not fit the DL1000 V-STROM800DE Carrier, so I purchased a ZBracket from a DIY store and installed it.
But I am satisfied with the firm fixation and the capacity.
View detail
The convenience of Tank Lock is retained, and it goes in rather well.
I had been using Tank Lock for a while, but ordered this because my Fastener broke.
The capacity is just right for a touring mapple, a glasses case, a memo pad, etc.
The only thing that bothered me was that when closing with the fastener, there was a buckle in the middle of the fastener that got stuck.
Why is there a Buckle in the middle?
It's strange
View detail
GIVI indeed.
The B47 boasts the largest capacity of all the Mono-lock cases, and it does not look out of place on a large motorbike.
The capacity is sufficient for my needs, and I have a Helmet + a bag of tools + documents.
Side case is also available, but this one is usually sufficient.
View detail
![Fitting for Monorack [7707FZ]](https://img.webike-cdn.net/catalogue/images/91664/18890_01_TS.jpg)
Mounted on 250DUKE
I was thinking of adding a Carrier in terms of style, but I thought it could be a substitute for a Carrier without a Top case, and also I thought it would be too much of a fussy thing, but I guess it is not so much once you get used to it.
It went on the 250DUKE with no problem, as it should.
When installing, there should be no problem if the entire unit is temporarily assembled while tightening it at the end.
However, it can't be helped that it is Steel, but I think GIVI's Bracket is quite prone to rust in the smallest details.
View detail
Use only LED Lighting Parts
Purchased to add High Mount Stop Lamp to GIVIRear box.
Various parts are included in the kit, but only LED Lamp parts are used.
Installation is easy from the BoxReverse side, and I extended the wiring myself with an Extension Cord to the bottom of the Seat. The wiring does not look good, but it is not visible from the outside.
It is an exclusive product, but the price was a bit high for just the Lamp component.
Reference and
The color of the Base of the BoxBody is more than Red. [Color] Smoke is more noticeable when lit.
Around Lamp (Inside) The reflective material was stretched over the
A hole of approximately 7mm is drilled in an inconspicuous location at the bottom of the Box.
View detail
![Top Case Fitting for Monolock [SR1191]](https://img.webike-cdn.net/catalogue/images/104416/1_165032128479988800_m_9wdoa_l_TS.jpg)
Fits: HONDA CRF250L, HONDA CRF250L〈S, HONDA CRF250 RALLY, HONDA CRF250 RALLY〈S
Installation is Large size.
The style after installation on the motorcycle is not too assertive and is good for parenthesis.
The Carrier is not noticeable because it is dedicated to GIVIMono-lock case, and it is nice to be able to install it low.
Installation was a challenge.
It is difficult to explain, but when the Seat is removed and installed, the Seat cannot be put back on. Also, if you leave the Seat in place, the Carrier will not fit. The product is so precise that there is no room at all. I had to push it in a little too hard. I think this may be because the Seat is wider on the RALLY50.
View detail
Sorry, it's a relatively backward choice. (●´ωTranslated by.)
I have a Tank Lock (ST611B) and I like the design and construction of this one better....
When I put my Camera on it, it presses on the phone part and might break the phone, so I searched for something with a little more height and bought this model with excellent cost performance.
The length and width are slightly reduced, and the entrance and exit are also narrowed, so it is slightly difficult to put in and out, but there is no problem when it comes to aiming height, and even if you use the Smartphone Holder inside, it was large enough to be durable, so I will switch to this one.
The fact that the insoles on the underside can be removed is also interesting. The underside of the 611B was quite hard, so I wondered how it would be for the Camera, but this seems to work even if another pad is placed on the underside.
On the other hand, the surrounding area is soft, or rather, not firm.
Relatively speaking, it is OK, but my personal opinion is that I would prefer something a little more solid and within the price of 611BClass, which can be 1L larger.
By the way, as you can see in the photo, I used Seat lockFlange S430 to attach it to the Rear Sets, because it is difficult to attach it to the Tank. The reason is that it is difficult to put it on the tank.:Pair (for Left and Right) Is it because the cowl of "1" is a little too small? It didn't go well.
View detail
When in doubt, this Manufacturer
Can be attached to Y's Gear's Rear Carrier X FORCE (Q5K-YSK-139-E01) without any modification.
For installation on the Carrier, only the Bolt+Washer+Nut supplied with B37 is required, and the W-shaped Bracket is not necessary.
When I saw the actual product as a Single Item, it seemed too large for the vehicle, but when I installed it, it was neither too large nor too small.
View detail
capacity
I use GIVI for my two motorcycles and the good thing about GIVI is that it can be used for multiple vehicles as long as the base is attached. I thought the capacity would be large for a 43, but it was a little smaller than I had imagined. The space at the back of the box allows you to put a sticker of your driver's license camera. If something gets caught in the locking mechanism, it can get stuck and prevent the box from opening or closing. I am a little dissatisfied with the 39Liter, which I used before, because I could lock it easily. View detail