Reviews
Fits: Others For UniversalScreen
Repair Parts are well stocked.
I had only the Screen, so I purchased only the Repair Parts and was able to install them.
The installation was easy to understand because the Instruction Manual can be downloaded from the website.
The feeling of using it is not a problem with wind pressure, though, as I have used it before,
The Cap of Included Parts:has the BALI in the image, which was prepared with a Cutter Knife and then installed.
The installation points are the Clearance and Angle of the Screen and the Light, which change the appearance of the Motorcycle.
As a request to the manufacturer, we would like to sell only the Spacer, which is attached between the Handlebar and Clamp, as a Single Item.
I was so satisfied that I Repeat both Left SideRight Side.
View detail
Fits: HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SF
Firmly looks good, but a little hard to install.
Installed on CB400.
It can be attached without removing the OEM Tandem grip.
The front side is co-tightened to the rear shock, and the carrier side replaces the 1 pc of Tandem grip fixed bolt that comes with the carriers.
The finish is beautiful, and the matte, elegant paint is not noticeable.
The problem is that the bolt did not bite into the screw threads, and it took a lot of time to re-try and re-try. If you have never tinkered with motorcycles before, there is a possibility that you will screw up the grip or ride it with an incomplete installation. On the other hand, if you are skilled enough to replace the oil, you should be able to manage. The Torque and order of work are all written in the Instruction Manual, so there is no need to worry.
The box bracket is small enough to fit almost any size, but too small to be used as a carrier. However, it is too small to be used as a carrier.
View detail
Fits: SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX, SUZUKI SKYWAVE650 burgmanLX
Larger than OEMScreen
It is very cheap than buying from OEM, and the sides are sized up to the equivalent of a Knuckle guard.
It is larger than OEMScreen.
Unfortunately, the thickness of the product is thinner than the OEM, but the strength of the product is smaller than the OEM, so the product may flex at high speeds,
Wound is more likely to be attached compared to OEM due to the difference in material.
View detail
Practical or Dress-up
I had difficulty with the installation because I felt like I didn't explain it well enough.
I thought that the Size might not have been produced by manufacturing, but if I calmly aligned the Screw holes, it was perfect.
I think NORMAL is good because it makes the cooler box look like a cooler box, but a little Wilde.
I don't have any practical use for it.
If it were $2,000 cheaper, it would be 5 stars.
View detail
Fits: Others OBK58/42 : V56 : TRK52 : V46 : TRK46/33 : B33NMK : V47 : V40 : B47 : E470 : E450 : B37 : E370 : E350 : E340 : B33NML : E300N2 : E260 : E230 : OBK48/37 : V35 : B27N : B360 : E250
for Replacement
I used to buy a GIVI 45LiterBox and used it for years, but one day the key suddenly stopped turning. After using it for a while, it stopped closing at all, so I decided to replace it.
I was worried because I did not know how to replace it, but I saw a video manual on DAYTONA's site before I purchased it that showed how to replace it, so I decided I could do it myself.
If you are anxious, it may be a good idea to watch the video manual in advance before purchasing the product, because you can actually replace the product by following the manual video.
View detail
Simple construction
[How is it used?
Used to install a GIVI Box.
Was the one you received as per Image?
The Pipe diameter was thick and strong enough, just like the Image.
How was your experience with it?
GIVIMono-lock basePlate was also fixed firmly and was simple and well made.
[Points to note]
Quantity:Pair (for Left and Right) The two symmetrical parts were aligned at the back center and bolt-tightened.
The screw holes on the tire house side were a little difficult to align, so we installed it by picking up the four screw holes little by little.
How did it compare to other products?
No comparison was made.
▼Other than that... I tried to install KIJIMA's back support item number:210-4963.
The Shock absorber side of the OEM Carrier has a thin wall on the inside of the Shock, while the Shock absorber side of the OEM Carrier has a thin wall on the outside of the Shock.
The GIVI rack is thick-walled, and the thick flat washer on top of the Shock is removed and tightened with a cap nut.
The thickness of the plate on the Cap Nut side of KIJIMA's back support eliminates the screw space for the Cap Nut to stop.
It could not be installed.
View detail
Fits: HONDA Forza 250, HONDA CB300R, HONDA FORZA300, HONDA Forza350, HONDA Forza350
Rack for attaching Monokey base to MF17
I purchased this product for the purpose of installing a GIVI M7 FZSeries Monokey base 91332 on a FORZA MF17.
The installation itself is very easy and takes only a few minutes. However, the M7Base and the holes were not aligned, and the rack had to be modified by force to align the holes. I was surprised that the steel of the rack was quite soft and bent easily, but I managed to install it.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
Use with Fender Eliminator Kit
[How is it used?
I purchased this product to install GIVI's Top case on my MT-25 which I use for long trips and shopping.
There are many options for carriers, but we chose this product because we wanted to attach a GIVI Case and were a little concerned about the strength of the Grab Bar alone.
Was the one you received as per Image?
Bolt and Bracketetc. were included as shown in the pictures without any shortage.
Was the installation difficult?
It takes considerably longer to install than the Carrier with Grab Bar installation.
There is an installation instruction manual, but the Large section is explained in letters, so it was very difficult to understand MinusPoint.
Also, although the kit is not designed to be used in conjunction with the Fender Eliminator Kit, it was possible to install it in conjunction with DAYTONA's Fender Eliminator Kit at my own risk.
There is no interference with the Blinker, although it is necessary to place a 3mm spacer between this product and the Fender Eliminator Kit.
How was your experience with it?
The Tandem Footpeg and the Fender section are fixed in 6 places in total, so they are fixed quite firm.
It is quite stable, with no interference with the vehicle body or chatter.
It made shopping more convenient.
However, due to the fact that it is fixed with a Tandem Footpeg, KIJIMA's Helmet Holder cannot be used together.
[Included Parts:were they on?
All necessary items other than tools such as mounting Bolt, Nut, Bracket, etc. are included in the package.
[Was there anything that disappointed you?
As I mentioned above, the installation instructions are very confusing.
It is not enough to have a diagram like an assembled piece of furniture, even if it is explained in words....
In addition, the size of the cap to be attached to the bolt on the SIDE was not correct, so it was necessary to file it down to a size that would fit.
【Review】
Firmly fixed to the vehicle body, it makes shopping and other activities very convenient.
The holes were well aligned and there was no need for any special modifications afterward.
I would like to see a little more work done on the instructions, as the product was good.
View detail
Caution when installing on Inverted Front Fork
Many people have talked about the effectiveness of Screen, so I will spare you.
CB650R (2021) I installed it in
The CB650R has a taper handlebar, which makes it somewhat difficult to install in the handlebar section.
The center section does not match the handlebar diameter, so it is installed at the end, but it must be shifted slightly because it interferes with the Master Cylinder.
Since the clamp will be installed in a halfway position, it is recommended to use an anti-slip rubber or similar material on the clamp.
Installation on the front fork is even more difficult.
The CB650R has an inverted front fork, so the supplied band is not long enough, and a longer one must be provided separately.
Also, because of the shroud on the side of the body, the gap between the front fork and the handlebar is very narrow, and the only place where the handlebar can be installed without interference is at the top of the outer tube. (Image 2)
This mounting at the very top is tricky, and the rods that hold the Clamp attached to the Screen and Front fork are too long for the product-supplied ones.
Therefore, a separate length-matched rod is required here as well. (Image 3)
I hope the above information will be helpful to those who are thinking of installing this product in the same car model.
View detail
Fits: Others V46 : TRK46/33 : B33NMK : B47 : E470 : E450 : E370 : E340 : B33NML : E300N2 : E260 : E230 : V35 : B36N
For key unification
I bought the 470 for overnight use and have 3 keys in the Top case alone and 7 keys in the Key Holder when combined with the Motorcycle, Helmet holder, Part key, and Cable lock.
Moreover, with three keys, it is time-consuming to check which case is which key, so I purchased a security key, which is a same-key key and is hard to be pranked.
The replacement itself is simply a matter of removing the inner tapping screw, pulling out the lock set, and replacing the Cylinder.
However, if the spring and ball are rusted, the movement of the cylinder will be a little sluggish after assembly.
Recommendation to make them new together if possible.
Also, it may be difficult to insert the push button when the lock set is inserted, so do not be hasty.
It is a large Merit that three cases can be unlocked and locked with one key, but I felt that it was a little reluctant to turn because it was new.
I expect that the BALI will be removed as it is used, and it will become easier to turn.
View detail
We have no other choice.
There is no other option to install the Monokey case. Like the other impresarios, I feel that it is very solidly made. I am satisfied with the overall quality of the product, but something may need to be done about the Bolt and Nut as they seem to rust easily. The nut in the photo is 13mm, which is not often used in domestic cars, and there is no clearance with the tail lamp, so the socket cannot be used. If you want to install it by yourself, you need 13mm Combination or Glasses. View detail
Repair is easy! Some people want to change the color of the key.
I lost my keys.
Then I had to change the whole key cylinder and bought this product.
It was a Honda OEM Box, but I knew it was made by GIVI because of the shape of the key, so I bought it and replaced it.
It is not a particular problem, but you will need at least Radio pliers.
The new key is also hard to stick, so you might as well have at least a bar File.
View detail
It's heavier than you think.
I installed it on TREKKER's 33 Aluminum. Drilling is necessary, but the board is soft and resin Case. It is heavy though it is solid. Because it is not likely to tie a heavy thing here, I think that it was good even with aluminum light weight.
I don't see many people wearing it, but I bought it because my TentPole is long and I need a place to tie it down.
Because the screw is long and Rubber Bush is attached, I think that the water leak is not so much. It is the Level which doesn't become matter of concern because water drips a little from the gap of SmallPig.
It is said that SmallPig does not open, but it seems to open to about 90-degrees if it shifts a little. Because I do not use SmallPig, it is good.
View detail
You may need to be creative to fix it firmly.
I changed the Screen for Touring around Hokkaido.
In Hokkaido, there are a lot of insects, and after a day of riding, the Screen will be covered with crushed insects, so the Long Type Screen is essential if you think that these insects will stick to the Helmet Shield and your body.
Recommendation Point
The shape is very good for parenthesis and it looks like European Scooter.
Windshield is highly accurate, distortion-free and transparent, so it looks great.
It is Long Screen, but it is not so long, and it is a good feeling just for the purpose of seeing.
Windproof effect is also quite good, I think it will reduce fatigue in the case of long touring! 。 Also, if it rains a little, you won't get too wet.
The price is lower than other Long TypeScreen.
Bad Point
The height is just right for the purpose of seeing, but when actually running, the wind hits the Helmet from the shoulder quite well. I prioritized styling and price over wind protection, but I think a longer Screen is better for complete wind protection.
However, there is a part where the connection is omitted compared with OEMShield, and there seems to be a little rattle in the part where Shield is fastened with Bolt because Shield itself is not thick enough. When the engine is running or running, it may interfere with Cowl, or it may make a shaking sound, and it is quite bothering.
I added a slightly thicker RubberWasher to the Bolt section to hold it in place, which eliminated the chattering sound and made it stick.
View detail
I've had it on for 2 years and it's pretty good.
[How is it used?
Wind protection for highway driving
Was the one you received as per Image?
It is very similar to GSX1100KATANA's Screen and good for parenthesis.
How was your experience with it?
The wind no longer hit my chest, so it was as expected.
[Points to note]
Be careful not to overtighten the Handlebar mounting parts as they will crack if overtightened.
Because the screen is pushed by wind pressure and it may hit the meter case, I put the Sponge of the wound prevention on the meter case with Double-sided Tape.
How did it compare to other products?
I believe that GIVIBrand has the best quality.
View detail
Fits: HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION
FUSION + Long Screen = Cool!
I was going to get the GIVI Screen before I bought the FUSION. It's cool. But it's semi-smoke, so you can't see very well on a rainy night because there are water drops on it. Please be careful. View detail
It's too firm and secure, but it gets heavy.
I bought this because I needed a special rack to replace my OEM Top case with a GIVI MonokeySeries V47.
Does the rack Bracket extending from the Sub-frame make sense? At first I thought that I was going to have to wear it, but when I tried to put it on, I found that the Case was going to be installed in the back of the case, so I felt secure with the Bracket.
The only drawback is that it makes it heavier.
When it arrived, I was surprised at how heavy it was.
I think it's because Material is Steel.
I haven't weighed it, but I'm guessing it's close to 3kg.
Installation is also Maniac.
Quantity:Pair (for Left and Right) The Bolt and Nut, which connect the Bracket that extends into the Case with the Bracket that connects the Plate and the Bracket that extends into the Case, are particularly hard to work with.
I would not be able to tighten or loosen the glasses if they were not moving a bit more.
By the way, you'll never get a Ratchet!
The stability of the product after it is completed is uncanny.
It's just the weight, thickness and construction.
I have some concerns about the difficulty of installation, weight, Material, etc., but if you don't buy this, you can't put it on, so I have no choice.
But I don't think I'll regret it.
View detail
I think it's moderately good
In the OEMScreen, the wind hits the screen at high speed cruising and makes me tired, so I changed to this product I think that a comfortable speed is like OEMScreen+20km/h I am not tired at all to the extent that I drive at 80-100km/h at a leisurely high speed The buttocks become painful first View detail
Fits: Others V46 : TRK46/33 : B33NMK : B47 : E470 : E450 : E370 : E340 : B33NML : E300N2 : E260 : E230 : V35 : B36N
I wish it was cheaper with fewer parts
I bought this for a single key for the Top case and Side case
How about having a total of six of them with and without resin?
I hope it's a little cheaper
View detail
It should be handled with extreme caution
In order to unify the keys of Top case and Side case
I replaced it with the same number key
At that time, I made a mistake in assembling Spring and Gold balls and
When I put the key on and left it in the open position, the weight of the key almost made it lock
I can't explain it well, but the bottom line is that it is no longer possible to unlock the door and keep it level
It's quite an ingenious design, and I learned a lot from it, but it's not very user-friendly
I bought this Lock set without it
This is quite a lot of Gold, so if you can buy Parts in a more detailed and partial way I appreciate that
View detail