Reviews
Fits: KAWASAKI ZX-4R, KAWASAKI ZX-4RR
Effective in reducing Rear sinking
Even if the sag is adjusted, when the load is applied at circuit level, the rear end sinks and the car turns weakly in the secondary turn, so dampers are necessary. I purchased the 4RR exclusive product because it was available this time. The most Large 3.5cm height of Rear is raised. 。 Since the frame position will be relatively higher, it is safe to raise the frame up to 2 cm, since it will lean more deeply when parked on the side stand. View detail
You can't use the ZX-4RR in the up direction!
I used it to raise 2cm on ZX-4RR, but Link Rod length is 150mm, 10mm shorter than 25R, so it can't be used for raising direction. 25R is 160mm, so it can raise ±10mm=±2cm within 150mm~170mm range, but 4RR can only be used for lowering direction. Please note that 4RR can only be used in the downward direction! View detail
Can be raised or lowered freely
I had previously raised the ride height of my 25R with BEET's SportsLINK, but I couldn't stand the gold or silver-colored parts that stood out, so I looked for a product that was less conspicuous and more functional.
Installation is easy if you have a Rear Stand and Jack. However, it is difficult to adjust the plate under the weight of the car because of the narrow space, and it is difficult to turn the plate with Spanner, so it would be easier to turn the plate with Jacketc. There is an adjustment allowance of 2cm up and down, so considering the time and effort required to replace the plate, I think this is a good product.
View detail
For the sake of the Japanese.
I'm 174cm and have a 78cm inseam, but I had no problem running in the NORMAL with up to a thumb bulb.
However, I was advised by a senior V2 rider that it is better to have good footing until you get used to it because the Pani V2 has a waist-high SS posture and moves roughly at low rpm.
The current condition is about 10 degrees lower than NORMAL, and it can be ridden without anxiety when the car stops.
The advantage of the Most Large is that it eliminates the anxiety of stopping in a variety of situations.
Once you get used to it, you can easily adjust it from NORMAL to +20, so I think it was the right decision to include it.
The price isn't cheap, but it's several times cheaper than replacing parts due to standing moss, so I think it's recommended for people who are worried about their footing.
View detail
Is it essential for a city-riding Main?
Panigale is most stable when it is driven at a certain speed on Circuit and mountain roads It is You can run with a high center of gravity and fluttering, but once you get into the city, it becomes restless It changes quickly and becomes difficult to ride Well, that kind of motorcycle is SBK, and I haven't ridden a lot of other companies SS But perhaps we all have that characteristic The footing is not so different from the other THRUXTONR, but the posture maintenance in town riding is much better I wanted to lower the height of the car so that I could be more careful with my car The ride height has been lowered by only 2.5kg, but I can feel the difference when I step on the motorcycle The footing is better and the feeling of security is increased, but it is also much easier to ride around town The level of my Level does not spoil the feeling of lightness even on the mountain roads, and the lack of bank angle is not a problem It's not possible Now, I have only dropped the rear and left the front as it is I think it would be better to drop the Front as well in terms of the balance of the vehicle, but When it comes to running a circuit, you can easily raise the gears, so you can use your usual touring skills I'm going to put more emphasis on street riding and city driving as it is The finish of the product itself is good and the coloring is nice and calm The Carbon is a good looking product, but it's expensive, but it has a strong dress-up effect It's the first thing you need to put on, rather than parts, as it will directly affect your ride Maybe At this price, you can't go wrong with installing it View detail
Fits: DUCATI STREETFIGHTER848, DUCATI STREETFIGHTER, DUCATI STREETFIGHTER
[a Webike Monitor] -- -- since [ big-ticket ] a Parts, it was hesitating purchase, but it decided on purchase at last! Probably, it will be better to request a diffident direction from Schopp, although attachment was performed by itself. A
[a Webike Monitor] --
-- since [ big-ticket ] a Parts, it was hesitating purchase, but it decided on purchase at last!
Probably, it will be better to request a diffident direction from Schopp, although
attachment was performed by itself.
Although it ran after
attachment, probably because the former Setting influenced, it was a Cornering which becomes quite soft and is limp.
The rear spring was returned to the standard value, vehicle height was lowered, and when attenuation also raised and ran, the run changed.
Although it was not able to swell when the Axel was opened in the second half of a Corner, and a fearful thought was not able to be written and opened until now [
], after attaching this product, the standup very came to be very pleasant to come to open.
It is an indispensable Parts at 1098 systems of which he repents [ that what was necessary was just to have purchased honestly earlier and ].
View detail
Fits: DUCATI Scrambler, TRIUMPH Thruxton
It purchased by if a 2-cm Lowdown can be carried out by a Catalogue. even if it came out to the Tank fast and took it with 169 cm of our height, it was 足着き of tiptoe ちょい, but with this product, a guide peg came to be attached by ベタ also a Sneak
It purchased by if a 2-cm Lowdown can be carried out by a Catalogue.
even if it came out to the Tank fast and took it with 169 cm of
our height, it was 足着き of tiptoe ちょい, but with this product, a guide peg came to be attached by ベタ also a Sneakers.
It was also charm that
Pre-road adjustment and attenuation control can also be performed.
Since the
Main was a 足着き improvement, although not expected so much, if the engine performance of the Suspension itself was a town riding peak and a high-speed grade, this was enough as it.
It is touch near [ in
attenuation control strongest ] the state of a NORMAL.
Engine-performance exertion is carried out enough by a standard value.
In the
peak, a leeway is given with Line + aimed at.
Even if it enters by an Overspeed, it is easy to also make it further circle in an AxelOff.
This neighborhood may also have affinity with a Tire.
The Tandem was carried out at the
high speed, and it did not feel uneasy about a Gap, either, without being unsteady.
In the case of the
THRUXTON, the Sas exchange cannot be carried out unless it removes a Silencer.
A Jack is also needed.
If it does not have a grade tool which is
, exchange by itself may be difficult.
Even
being regrettable is that the tool in which a Lock nut for adjustment of a Pre-road to be able to turn now by hand, and act as Locke of it is fastened is not attached.
Very much satisfied except it.
View detail
Fits: DUCATI STREETFIGHTER848, DUCATI STREETFIGHTER, DUCATI STREETFIGHTER
It attached by itself instantly. if it is preparing, troubles will be suffered very much and it will meet -- although it came out and carried out, if it advances like a puzzle ring, considering a procedure, it can attach well. It is the blood of D
It attached by itself instantly.
if it is preparing, troubles will be suffered very much and it will meet -- although it came out and carried out, if it advances like a puzzle ring, considering a procedure, it can attach well.
It is the blood of DUCATI that not only a design but serviceability is designed firmly.
It is necessary to fix a front like a picture and to float a rear swing arm thoroughly.
since I was exchanging steps previously, I am satisfactory -- it is -- although -- since a jack stand does not start in case of the retractable step of normal, it will hang from head lining with a chain block etc.
a tank is removed -- although it is unnecessary, the black panel of the bottom both sides of a sheet is removed.
The adjustable rod is lengthened with the rear stand hung, and it moves to the location whose upper part bolt head of a link rod can be thoroughly seen from the crevice between frames.
A bolt is loosened, a rear stand is removed and a swing arm is floated.
If a bolt is pulled out by hand and a rod is removed, a swing arm will serve as bra~N.
A swing arm is supported and adjusted with the jack for four flowers so that the upper part bolt head of a rear suspension unit may become a location which looks perfect.
If a bolt is pulled out, the existing link arm can move to a free.
The rest loosens and pulls out the fulcrum bolt of the center of a link arm, and removes a link arm.
Shafts clean, it applies each part grease and constructs it by a reverse order.
Also when constructing, moving an arm, the location of a bolt is decided, and it fastens and is crowded.
The 8-mV bolting torque of the circumference of a link is 42N (you should use, if a torque wrench enters and meets).
Since the link rod attached the thing made from BabyFace from the start, it was used as it is, but it was able to construct satisfactorily.
Having straddled also sinks and the difference in Ho is known.
It is pleasure to pack setting from now on.
View detail