Reviews
Feet are Drill and determined.
[How is it used?
Touring
Was the one you received as per Image?
Yes.
Was the installation difficult?
It was easy.
How was your experience with it?
Beautiful feet.
[Included Parts:were they on?
Yes
View detail
Easy
[How is it used?
Very good
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy
How was your experience with it?
Manufacturer name is also Printed and cool.
[Included Parts:were they on?
It was attached.
[Was there anything that disappointed you?
nothing special
[Note]
As long as the standard pin is disconnected, it can be installed without any problem at all.
View detail
Looks great!
I love the look of this piece. It's much nicer than the rubber that comes with the bike, and the safety pin is much easier to deal with than bending the cotter pin every time. Plus, it's less wasteful! View detail
Dullness Solution
Rubber is just right because it was tacky. It can be installed by anyone right away. 。 If you think Rubber is lame, by all means. View detail
Good vibes
I was really not satisfied with the OEM rubber cap, so after installing it, I am Large satisfied. View detail
The product quality and finish of the cap cover are good
The product quality and finish of the cap cover are good. The anodizing color is also good. Remove the existing rubber cover and remove the pin Insert the Aella nut cover and insert a new pin into the hole of the cover for easy installation. In the case of genuine pins, the shape of the wheel is deformed when reassembling, so it does not look good, but when using pins from Aella products, I think it can be easily reassembled every time. View detail
Smart and clever axle nut cover Z900RS
Replaces the stock cheap axle nut cover with a part that has style and functionality No need anymore to straighten out cotter pin and replace each time chain needs adjusting Ok slightly pricey but does a great job Happy with the purchase ! View detail
There is nothing wrong with the product, but ….
It looks better than the bare OEM.
However, I was mistaken, but I thought it was Quantity because it cost more than 6,000 yen.:Pair (for Left and Right) I bought it because I thought it was a good idea.
The price for one Cap and one Split Pin was a cosmetic disappointment.
View detail
Because OEMCover is not cool.
I bought this because the OEM Cover is not good looking, and I was worried about the Rear Axle guard, but at the time of purchase, I was considering an external exhaust system, and there was a possibility that it would interfere with some of the exhaust systems, so I decided to go for the easy way out.
The design is much cooler than OEM. Personally, I think it would have been nice to have a product without the word "Manufacturer" or with a simple design.
Also, the cover itself is reasonably stiff, so I think it will protect the Swing Arm if the fall is just a standing fall.
As others have said, the space between the pins is too narrow to fit easily, and since I didn't have a plastic hammer, I couldn't knock it in, so I widened the pins a bit.
Also, due to the trial and error process, the grooves were scratched quite a bit by the pin, and the pin's clamping side (the side that goes out) was sharp, though not sharp, so it scratched quite deeply.
When I wiped it with Plexus, it became less noticeable, but when I left it as it was, it stood out as Large, so I think I need to be careful when installing it.
View detail
Also fits the Z900 , not just the RS.
Bought this for my 2017 Z900. It is not advertised as fitting to the non-RS model but installs perfectly. The rubber sock fitted as standard looks cheap and the throwaway cotter pins are awkward and wasteful to deal with. They had to go, but until now there was no solution. Thanks Aella! The Aella cover is well designed, of xcellent quality and just looks so clean! View detail
It's not bad, but the cosmetic?
It is the same color as the Front Axle Slider and the balance can be taken, and it is not bad, but I think the price is high. If it is half price at least, I think it is a bargain.
Is the Material penalized, or is it just enough to Cover you if you have a light standing gouge?
I don't think it's a replacement for Slider.
Well, Slider will be replaced if it falls, too, but it is Style outstanding compared with Rubber cover of NORMAL.
Installation is very easy, just remove the NORMALRubber cover, pull out the Split Pin, put it on and insert the Pin.
View detail
with good looks
Whenever I adjust the chain, I change the split pin for the Axle Nut to prevent it from falling off, but the home center in my neighborhood only has StainlessSplitPins, and I always get frustrated because I can't bend them cleanly. I bought this product without hesitation after learning about its existence just as I thought it would be good without a cover.
As for the device, it just fits and sticks the Split Pin, but because it was unexpectedly hard, I attached it while lightly beating it with the plastic hammer.
It looks better and seems to be more functional, but I'm a little worried about whether I can remove the Cover without scratching it.
At any rate, the dress-up effect is Aria-like because of its high quality and good appearance.
View detail
It's not half as luxurious as it sounds!
The cap is well machined so the Snap pin is a little tight but it stays in place. It's a lot more expensive than the OEM Rubber cover. This is a great product.
Material:I think PlasticCap can be expected to serve as a slider in case of a fall.
However, I think this price is still too high just for the Cap and Snap pin.
View detail
Parenthesis good&Refreshing
I used it after adjusting the Z900rsChain, no split pin needed, and the OEM BlackRubber cover looks cool. I recommend it. View detail
This is exactly the Parts I wanted.
The Z900RS must prepare the split pin when adjusting the chain.
I was looking for a Beta pin that is both fashionable and easy to maintain, and this is exactly what I bought it for.
I'm very happy with the accuracy of the NutCover, and the Pin is not a waste of time.
I dare to say that the drawback is that the price is too high and the end surface of the Pin is poorly finished and does not slide in comfortably as it is.:It's Stainless Steel, but the color is not good, so I polished the edge surface to be smooth, and the PinBody is also polished to Polished (although you can hardly see it)
I feel the mark printed on the cap is noisy personally, but it is bearable. However, because the position of the hole and the print are not matched, when you want to adjust the position of the mark, you need to adjust the position of the Axle Shaft.
It takes a certain amount of effort to pull out the pin, so I think it won't come off while driving or get tricked on the road, but I fixed the wire with insurance.
View detail