Reviews
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
Side Stand is perfect!
Panigale and Streetfighter boots do not have good footing for most Japanese people. I am 177cm tall, but when I use a type of racing boots with the heel covered with a resin protector, like the ones from Pine Starz, the part where the heel hooks onto the side stand is too short and I slip and run away. When I am in the riding position, I can get it out with about a 50/50 chance, so when I am in good health, such as when I am refueling, I can stick it out a few times, but when I am tired, I can't get it out. No more." and I had to get off the Motorcycle and take out the Side Stand. If I had a normal leather or rubber bike, I would be able to get off the motorcycle and put out the Side Stand without any problem.
The AELLA product is almost twice as long as the AELLA product, so the Side Stand can be easily produced.
View detail
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
Easy to use.
[How is it used?
STAND was purchased before the car was delivered because it was difficult to get it out,
I installed it immediately.
Was the one you received as per Image?
It was as Image in the picture.
Was the installation difficult?
It was easy to replace with Wrench.
Locktite is applied to prevent loosening.
How was your experience with it?
The Hook is in view even when straddled,
It is easy to STAND.
[Included Parts:were they on?
There was a Handling Instruction Manual.
[Was there anything that disappointed you?
None in particular.
View detail
Fits: DUCATI SCRAMBLER 1100, DUCATI MONSTER 797 Plus, DUCATI MONSTER 797
AELLA
Tilt when parking has been improved:?? View detail
Very good as Design
[How is it used?
Aiming to reduce Damage in the event of a fall
Was the one you received as per Image?
No different than the photo shown.
Was the installation difficult?
Because it is to be installed inside the exterior Cover (Cowl) from the 2023 model year,
Installed by Dealer.
How was your experience with it?
I hope it is never used because it falls over and exerts itself.
It looks very good and can be a dress-up.
Red and Blue Anodized are available.
It is very good that it does not stand out badly due to the thin Ring line.
The structure itself is also very beautiful.
The surfaces do not protrude too much, so they do not get in the way.
When there was a Damage, I was told that I could purchase the parts Single Body from AELLA,
Maintenance afterwards can also be assured.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: TRIUMPH Daytona675, TRIUMPH STREET TRIPLE 85, BMW S1000RR, BMW S1000R, Others Screw diameter:M8
Slider and Stand Hook
[How is it used?
Used as a Slider and Stand Hook for the rear section
Was the one you received as per Image?
No change from the image.
Was the installation difficult?
Installation is very easy, but the screw holes are made of aluminum,
Care must be taken in Torque management, as screwing in too much will make the screw holes ridiculous.
How was your experience with it?
The shoes are just right and look great when worn.
Screw mounts are available in Red or Blue Anodized.
The inlays of the Outer and Anodized sections are very precise and perfectly designed.
Be careful not to put it in at a bad angle, as you may bite it.
Anodized processing is also very clean.
The engraving is likewise very clean.
All of AELLA's products are extremely accurate.
As a Slider, I would have to fall over to know for sure, but after examining it, it seems to be doing its job well, so I adopted it.
It can also be used as a Stand Hook, which is very convenient.
[Included Parts:were they on?
A special Mounting Bolt is included.
A simple Instruction Manual for handling is available.
[Was there anything that disappointed you?
Nothing in particular. Perfect.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Slider
Slider installed.
After removing the Side Cowl, remove the Under Cowl.
After supporting Engine with Jack
Remove the Engine Mounting Bolt.
Base plate is co-tightened with attached bolt
Cowl back and SliderBody fixed.
The RS660 Cowl has no extra wiring.
(Note only the Wiring of Under Cowl's Shift Pedal)
It can be easily removed, and the work was completed in about an hour while reading the accompanying manual.
Tools required are
Hexagonal Wrench (Cowl removal Short Type is useful in some places)
13mm Socket (Engine Mounting Bolt removal)
Torque of T25 (Reverse side of Side cowl)
8mm Hexagonal Socket (with attached Engine Mounting Bolt tightening torque specified)
6mm hexagonal socket (with SliderBody tightening torque specified)
It would be nice if the
Clearance was fine and the texture of the Anodized Treatment was good, I would recommend this product.
View detail
I don't want to confirm the effect, but
The workmanship precision of the product is quintessential.
I wish I could spend time as Dress-up parts without knowing the effect.
View detail
I am satisfied
The installation was easy, even for a beginner like myself, because all I had to do was fix it in place with a screw. I was a little worried about whether it would fit on my s1000rr 2023 VERSION, but it did. I would have appreciated it if you had written "2019-2023" or "Hadrill" instead of "2019-" or "2019-2023" for the applicable range. View detail
Fits: DUCATI XDiavel, DUCATI PanigaleV2, DUCATI PanigaleV4R, DUCATI PanigaleV4, DUCATI 1299 Panigale, DUCATI 959 Panigale, DUCATI 1199 Panigale, DUCATI 899 Panigale, DUCATI StreetFighterV4, DUCATI StreetFighterV2, DUCATI Diavel1260, DUCATI Diavel V4, DUCATI Diavel
Highly accurate product.
I use Slider and others AELLA.
The high precision of the construction makes it safe to wear.
View detail
good-looking
I feel that this is indeed an AELLA product!
Good to make and good to look at.
View detail
textured good feeling
Unlike other companies' products, this product was selected because it is secured with two bolt points, which seems to have less risk of damaging the female screws of the frame and engine when it falls over than those with a single-point fastening.
The surface finish is beautiful and of high quality, as is typical of AELLA, a manufacturer of parts with a high quality feel.
The screw holes were easily installed without gapping by lightly applying a jack to the oil pan.
View detail
Fits: DUCATI XDiavel, DUCATI PanigaleV2, DUCATI PanigaleV4R, DUCATI PanigaleV4, DUCATI 1299 Panigale, DUCATI 959 Panigale, DUCATI 1199 Panigale, DUCATI 899 Panigale, DUCATI StreetFighterV4, DUCATI StreetFighterV2, DUCATI Diavel1260, DUCATI Diavel V4, DUCATI Diavel
Everyone loves Red and Black, right?
[How is it used?
Street Riding Only for now.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy to use, but requires two sets of hexagonal bar spanners when tightening.
How was your experience with it?
Function as a Slider is still unknown, but it looks good.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: DUCATI SUPER BIKE 1299 S-L, DUCATI SUPER BIKE 1199S-L, DUCATI XDiavel, DUCATI STREETFIGHTER V4 S, DUCATI STREETFIGHTER V4, DUCATI PanigaleV2, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4, DUCATI Multistrada 1200S Pikes Peak, DUCATI Multistrada 1200S, DUCATI Multistrada 1200S, DUCATI Multistrada 1200S, DUCATI Multistrada 1200 Pikes Peak, DUCATI Multistrada 1200 Enduro, DUCATI Multistrada 1200, DUCATI MONSTER 1200S, DUCATI MONSTER 1200S, DUCATI MONSTER 1200R, DUCATI MONSTER 1200, DUCATI DIAVEL
OK for now.
When I asked AELLA about it, they told me that the wheel shape was different and that it was not compatible with my car model.
The response was, "It might be attached, but we have not checked the actual vehicle, so it is not compatible.
So, this time, I bought it as a human sacrifice.
The installation itself went without a hitch.
View detail
Fits: BMW S1000R, BMW S1000RR, TRIUMPH Daytona675, TRIUMPH STREET TRIPLE 85, Others Screw diameter:M8
AELLA is good!
I think it's the best when it comes to accuracy!
The color is in the Bolt, but the dimensions with the Stand Hook are also Exactly.
Great job!
Not bad looking!
View detail
Fits: DUCATI Multistrada 1260, DUCATI Multistrada 1200, DUCATI Multistrada 1200
The angle of the Side Stand was too steep and difficult
I used to have to pull it out every time I got in and out of the Motorcycle, but thanks to this, it has become a large change and much easier. It is only 6mm thick, but it works great. It is a good product. View detail
Fits: DUCATI MONSTER S4R, DUCATI MONSTER S2821, DUCATI MONSTER S2797, DUCATI MONSTER S21200, DUCATI MULTISTRADA 1000DS950, DUCATI MULTISTRADA 1000DS1260, DUCATI MULTISTRADA 1000DS1200 DVT, DUCATI MULTISTRADA 1000DS1200, DUCATI HYPERMOTARD950, DUCATI HYPERMOTARD939, DUCATI HYPERMOTARD821, DUCATI STREETFIGHTER1098, DUCATI SUPER BIKE848, DUCATI SUPER BIKE1198, DUCATI SUPER BIKE1098, DUCATI SuperSport939
Easy installation!
It is perfect for the Front undercarriage support.
Installation is also very easy!
View detail
Slider without discomfort
I had it installed before delivery at Dealer and I don't want to experience the effects lol. View detail
Fits: DUCATI MONSTER 821, DUCATI MONSTER 821, DUCATI MONSTER 1200, DUCATI MONSTER 1200S, DUCATI MONSTER 1200S, DUCATI MONSTER 1200R
It's still cool.
As I said, it is made by AELLA, so it has a good texture and elegant appearance.
The work itself was not difficult, and I was able to install it smoothly, but I had to shift the Water Hose 1m Diameter 19mm because it interfered with the Hose, so I paid close attention to the work. It was also difficult to tighten the band in its original position, and after installation, I drove around for a while checking for water leaks.
I wrote about my concerns in the image section, but I am generally satisfied. (Except for the price.)
View detail
Fits: TRIUMPH STREET TRIPLE 85, TRIUMPH Daytona675, Others Screw diameter:M6
stand hook slide
The product is very nice and exquisite,I personally think it's pretty good .The disadvantage is that after the tax is added, this product is quite expensive, for me. View detail
I'll have it put on at the dealer.
I fell on Circuit, so I put it on next time to get some.
I liked the effect quite a bit as a dress-up.
View detail