Reviews
be extremely thorough, focusing on even the finest of details
Tank can be oriented 360 degrees to any desired angle. View detail
Attracted by the appearance, it was installed!
I was attracted by the look of the product as per the Title.
The vehicle model is ZEPHYR750.
I installed a black Gale MASTER to match Striker's Rear Sets, but the hose to the Reserve tank looked depressing, so I installed the said Aluminum Tank!
The area around the rear master is now refreshed and looks tighter.
However, the high price and low practicality (other than appearance) of the Aluminum Cut-out makes it a poor cosmetic choice.
View detail
Nice product
Hello everyone, this is a good product and I recommend it to everyone.titanium pin more light. This is 100% original, you can buy with confidence. also easy to install View detail
Nice oil tank
Hello everyone, this is a good product and I recommend it to everyone. Easy to install. This is 100% original, you can buy with confidence. View detail
Rear masterReserve tank
There are three different reserve tank angle settings
Large Satisfied
View detail
Necessary when adding MASTER's Tank
[How is it used?
Touring and city driving
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Slightly stiff and difficult to install.
How was your experience with it?
It was good
[Included Parts:were they on?
It's not attached.
[Was there anything that disappointed you?
There is none
View detail
it's recommended
It is great to be able to change the position of the Hose without difficulty. View detail
Galespeed reservoir
Great piece of equipment. Great quality. Gorgeous outlook. Top notch finish and workmanship. Feels great in combination with brembo p2 caliper. View detail
Galespeed
Great piece of equipment. Great quality. Gorgeous outlook. Top notch finish and workmanship. Feels great in combination with brembo p2 caliper. View detail
GALE SPEED Titanium Goal Pivot Pin for GALESPEED Clutch
[How is it used?
Used for Wire Clutch Holder Kit by GALE SPEED.
Was the one you received as per Image?
Elabo RateSpec. is equipped with Titaniumium goldCoated PivotPins from the beginning.
The normal Wire Clutch Holder Kit is iron-like and would help prevent rust.
Was the installation difficult?
It is very easy.
How was your experience with it?
It feels smoother and looks more Gorgeous.
[Included Parts:were they on?
Instruction Manual only.
When installing
For now, Grease was applied and then installed on the Wire Clutch Holder Kit.
View detail
It's all about looks.
Rust comes out, so replace it as soon as possible.
It's all about looks.
It is not faster or lighter.
You should have put this on from the start.
View detail
ส่งเร็ว ส่งไว ของแท้ คุณภาพเยี่ยม View detail
just right (length, width, etc.)
I bought this to change at the same time when I replace my Master tank.
Material:It's a great way to make sure that you don't have to spend a lot of money to get a great product.
View detail
It's a regular Hose.
It is an ordinary Reserver Hose. This is probably the same no matter which manufacturer you buy. As a side note, Gail's MASTER comes with 2 types of Nipple, so you can use both brembo type thin hose and Nissin type thick hose.
If you're watching this Impression!
You should buy HoseCutter along with Hose, it's surprisingly difficult to cut straight with Scissors or Nipper. It will be diagonal.
View detail
usually
The mounting mount rotates 360 degrees around the tank, so it is easy to position when installing. I think that the construction is also good as a matter of course, even if it continues to run at high speed, there is no such thing as oil oozing. View detail
good
Installed on a brembo CORSA Corta.
The direction of the hose can be changed freely for a high degree of freedom in layout and easy installation.
Smoke Type and good looking.
View detail
Installation to Top Bridge
I bought this for the purpose of attaching it directly to the Top Bridge without going through the bracket, and it was the right choice. The Nisshin's are too large to fit, so you'll need to prepare a slightly narrower bet for Brembo. View detail
Black smoke
It is used for the Radial master of GALE SPEED.
Bracket is also GALE SPEED! 。
I like how easy it is to position the tank.
View detail
On the move to Tank …
I bought a rear master cylinder for my GSX1300R
The location of the OEM Fluid Tank is poorly maintained and we decided to relocate it
The 90-degreesNipple that came with the OEM was not aligned well … I replaced it with a StraightNipple from Option Parts
It took a lot of time and effort to make the tank bracket by myself, but I am satisfied with the performance and maintainability I've got it
View detail
To adjust the length
I bought a rear master cylinder for my GSX1300R …
I made various adjustments as I built it in
It's just not long enough … I thought about it You'd be quicker to buy it He said
I'm very happy with the way it works
View detail