Reviews
brembo
It is installed for Brembo caliper installation.
There seem to be no problems with appearance, strength, etc.
View detail
I wanted a little more load bearing capacity.
As for installation, it is easy to understand if you look closely at the Illustration.
If you remove the Plastic Blind on the side of the Seat, you will see the M8 Female Screw on the Seat rail, and simply fasten it with Bolt through the attached collars in 4 places.
The carriers are narrowed backward from the width of the rear edge of the Seat and extended at the same height as the Seat, so that a small type Seat bag can be installed without any problem, and a slightly large type bag can be fixed depending on your ingenuity.
However, the load capacity is limited to 3 kg, so care may be required when placing very heavy objects on it.
The Carrier and Bracket are made of iron and painted black, but I think it is probably a baked-on paint with strength.
The collar between the Bracket and the Seat rail is Material:The M8 Bolt that holds the Bracket is Stainless Steel, but the Bolt that holds the Washer, Bracket and CarrierBody is Plating.
I prepared Stainless Steel Black painted Bolts to match the Black Carrier.
The silhouette is not a typical "carrier" silhouette, but rather a natural, backward design that extends smoothly and naturally.
In detail, on the top surface of the Carrier Gcraft" The product had a Laser engraving of "L", and I liked the fact that they did not cut corners.
View detail
The CT125 Shift change is now in place.
Many people recommended it on the Net, so I installed it.
It's been about 600 km since the car was delivered, and I had the impression that the shift change was pretty smooth even before the installation.
The installation process itself was no problem, especially if you watch the instruction manual or video streaming.
My impressions of the installation are that it's a bit of a pain, especially when doing Shift change and Downshift.
Before the installation, it seemed to flex a little.
I can now enter with Snap.
The quality and texture are high.
It's expensive, too.
If you are going to ride a large car for a long time, I thought it would be better to install it as soon as possible.
View detail
Generally satisfactory, but you need to be careful not to pinch your fingers.
The design is also very firm, so I think it's suitable for putting a seat bag on it.
Easy to install. The function is perfect.
Two things I thought were subtle.
You can't use it as a Grab Bar. The Grab Bar is sold separately.
The gap between the plate and the body is too narrow, and when closing the seat, do not hold the side of the seat.
Although there are not many choices for the Grom (JC92) Carrier, I think it is a satisfactory product considering its intended use.
View detail
Grom's Shift feel is much improved.
These parts tightly reinforce the slightly unreliable shift feeling of the JC92 Grom.
The effect is extremely large, and SnapSnap will enter. The effect is very large, and SnapSnap will enter. Neutral, which is difficult to enter, will also enter immediately.
The body is made of aluminum cut-out, with press-fit bearings and a material spacer collar.:Aluminum.
Cap screw included is Material:Since it is made of Stainless Steel, you may want to apply some anti-glare grease.
The installation can be completed in less than 30 minutes if you have read the manual carefully and have the right tools.
The Shift feel is much improved, so it is a super recommendation, but the price is reasonable, so I gave it a slight Minus rating.
View detail
Cool
I'm not sure if I'd like it if it was a little taller. View detail
+16 on my monkey baja
I mounted the +16 version on my tuning baja. Nice finish but I give 4 stars because of the higher price. I can't upload a picture but I can deliver them by mail, also for my other reviews WEBIKE View detail
It could be stronger.
I installed it because I could not feel any reaction force in the rear brake of 250SL and it was difficult to control.
It's better than nothing, but the spring is weak and needs to be stronger.
I installed it because I had no choice, but the price is rather high for the color and spring.
However, I can now feel Pedal's treadmill and Fee Ring is better.
View detail
To prevent scratches and stains
If you read the instruction manual and check the parts, you can install it with just three screws without any problem at all.
I haven't tumbled or fallen asleep, so I haven't experienced the effect, but it is true that I feel safer with it than without it.
There were some scratches from previous maintenance. I'm sure it's not ineffective.
The only problem is that it's not cheap.
View detail
Feel the firmness in the Shift!
I feel that Neutral is a little easier to produce.
GEAR is also a Recommendation because it makes it easier to enter ScauperScauper.
View detail
It was exactly what I expected.
I decided to use GCraft's Rear Carrier, which is more compact and cheaper than the OEM product. The installation is not particularly difficult, and I am using it by installing the Top case of 40L. In daily commuting, I put a Backpack of about 3kg in the Top case, but I am satisfied that the Top case can be fixed firmly without anxiety that it rattles or comes off.
Even if you remove the Top case, it looks nice and neat.
View detail
Expected
I've been looking for a new GCraft product for a while now, and I ordered it as soon as it was released as Type 2. View detail
Appearance highest
It is well made and Cost effective. The installation process is easy even for a clumsy person like me. View detail
Exactly to the 6cm Long G-Cla Swing Arm of DAX.
I attached it to DAX's 6cm Long G-Cla Swing ArmSpec.
Before this product, I used to install the same GCraft 14/16cm long wheel, but it was too long and I had to pass the brake arm beforehand to remove and install the rear wheel.
This was very annoying and I wanted a third hand.
With this product, even after the Wheel is fixed to the Swing Arm, if the Torque rod is free, it can be fixed to the Brake Arm.
It is possible to pass through, so the serviceability has been improved remarkably.
In the explanation of using for MONKEY for DAX on the HP of the manufacturer, it became suitable for 14/16cm long, but
The 8, 10, and 12 cm Long's are much easier to use!
View detail
Shift feeling is cooler, but it doesn't cure the disease of not being Neutral.
The other reviewers said that Neutral was easier to get, so I put it on too.
After about 10km, I had about 20 opportunities to get into Neutral, but as usual, I couldn't get one shot into Neutral.
What I felt when I put on the Shift guide was
The tightly feeling has been improved, and the fee ring of shift change has been improved.
After failing to put it in Neutral and getting into a halfway Neutral state with ”--”Mark, I think it's easier to adjust to where ”N”'s Switch reacts. (Lol)
I've already driven 2,000km, so I guess I'm getting into a weird habit.
I wonder if it's now in Neutral if it's installed at the same time as the vehicle is purchased.
I thought
View detail
Quintessential GCraft
I don't want to soak my back in the seat, so I decided to look for a carrier …OEM looks sturdy, but the length is short and it looks like THECarrier. It was easy to install. View detail
G-Craft G-Craft GCraft Rear Carrier
I bought it because I liked the design, and when I installed it, the design was exactly as I wanted it to be, and I'm glad I bought it.
I think it would have been better if it was a little larger.
I'm a little nervous about the 3kg load capacity, which is the same as HondaOEM's, but I want to use it so that it doesn't put too much strain on the frame.
View detail
Quintessential GCraft
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
it's simple
How was your experience with it?
The angle of Number is good and the weight is light because of Aluminum.
[Included Parts:were they on?
All are available
[Was there anything that disappointed you?
This is a special product for each car model, but Blinker Harness modification is required. (I can only make my own.) It'd be a lot easier if you could just wear it.
▼ Opinions and requests
It was a shame that the Gold amount was so high that it needed to be processed.
View detail
Easy to install
I bought this to install a GIVI top case. The installation was very easy and although I have attached an instruction manual, you don't need to look at it to install it. Thanks to your help, I was able to install the GIVI top case as planned.
The only drawback is that you have to tighten the seat rail with bolt to fix the plate, but if you are not careful when you install the seat, you might hurt your finger between the seat and the side plate. If you are not careful when you install the seat, you may hurt your finger between the seat and the side plate.
View detail
Not really perfect
The quality of the bracket is good but the mounting holes for the caliper should sit lower bcoz the brake pads only attached about 70% to the disc rotor. View detail