Reviews
GCraftZ2Seat Cowl exclusive Club bar
As expected of GCraftExclusive Design, it fits perfectly and looks great, and I love it. View detail
G-Craft's Club bar
Design is good
Easy to install
Easy-to-hold shape
View detail
Carrier can be installed at the same time for easy loading
Mounted for originality and possible use as a load rack.
The Carrier and the simultaneous installation is a bit messy and unobtrusive, hmm….
Incidentally, if you install the Carrier at the same time, you need to prepare the Screw by yourself.
Single body parts have a luxurious feel, and the engraved logo is also nice parenthesis.
Easier loading with Carrier at the same time is a GOOD thing.
View detail
Convenient to have
It is not necessary to have it, but it is convenient to have it!
Stylish and cool when present!
View detail
Cool!
I like this shape the best!
It is well made and I have no complaints!
View detail
The non-gussied up design is GOOD!
The Grab Bar by DAYTONA that I had been using up to now was not so bad, but I was concerned about the gills of the Fender Eliminator, so I replaced it with this one, which is a less protruding design. I was concerned about the gills, so I replaced them with this one, which has a design that does not stick out too much.
The sleek and clean design is perfect for the Fender Eliminator Motorcycle, and I am very satisfied with the large size.
It's easy to grab and go, and the performance is fine! Now if only it were a little cheaper.
View detail
Grab Bar G-Craft
I was torn between the Grab Bar and the Rear Carrier, but I chose the Grab Bar for its frequency of use and appearance. I think it is a matter of taste, but since the area around the tail lamp of MONKEY is plated, I wondered whether I should match it with plating or put it together with black refreshments. As a result, the black of the frame and the texture of the grab bar were close, so I think it was a good choice. 。 I thought it would be easy to install, but I had to shift the Rear Fender a bit before I could install it. Also, there is not much clearance with the Rear blinker, so I had to work while fine-tuning. Initially, the Right Side blinker was in contact with the Rear blinker.:Pair (for Left and Right) The difference in Clearance is due to the bolt nut included in the kit. I put a black bolt nut in the opposite direction of the instruction manual because it looked bad. I will observe the progress and be careful of the Clearance. It is a long story, but you will need a tool such as Hexagonal Wrench or Glasses Wrench to install it. Be careful not to lick it, as it is hard and tight! View detail
Cool
I'm not sure if I'd like it if it was a little taller. View detail
A little Accent on Tail?
Personally, I might be pretty unhappy with it!
I installed it on my JC92.
If you want to keep the OEM look, this is the right choice.
It is easy to install and you just need to plug it into the existing screw hole on the rail. It is very easy.
The strength of the product itself is the quintessential G-Craft. It's solid without looking like it.
However, it is unexpectedly difficult to hold because of Short Bar? If your fingers are a little thick, it is not much use because it catches in the gap between the bar and the Rear cowl.
It may be perfect for a kick rack to put your fingers on, but if you tandem for a long time, you will lose your grip.
When the Carrier is placed on the Rear Sets, it can be used as a fixed ground object.
As an overall evaluation, I can't recommend this product because its use is too limited.
If you like SMART design, this is the one for you.
It is not cost effective, so you should definitely consider carefully when buying one.
If you increase Coloring a little more, you can use it as One point, so how about improvement?
View detail
As expected of GCraft, the construction is different
It's been over a year since I installed it on MONKEY It's very convenient when I want to adjust the position when I'm on the road or in Garage It's quite a burden to use but there is no problem so far
Convenient, good looking, beautifully welded, no complaints, I couldn't decide between Long and Short It was just fine
View detail
very good!
I bought it with z2Tail of GCraft! I am also solid, making it exclusive for Balance, very good, is a recommended dish. View detail
Good vibes!
GCraft is solidly made.
I attached it with 31219 ShortTail Lamp Bracket and attached it, since holes for stopping the screw are the same, be careful when attaching it at the same time.
The conformity of Tail lamp for 4L was nice feeling without complaint
View detail
Building is the same as Chinese
I was expecting but I was sorry..
Until now I have used a lot of G-craft Parts and have not failed.
However, this time Large failed!
As shown in the photograph, welding is sloppy, around the welding is white discoloration.
The Instruction Manual is fairly tidy.
Use OEM of 5 LMONKEY around Tail in this Parts.
However, the three-stage Adjustable is said to be incompatible due to Blinker and others interfering other than the first one.
Since there is only one option in the end, there is no meaning of Adjustable.
Also, when installed normally, Blinker and Tail lamp warped up,
It looks like a Chinese cheap Tail lamp.
Since it can not be helped, I hit Base so that Tail lamp etc. become natural.
Thanks to hitting you made 2 stages of choice out of 3 stages.
So I made the position in the middle.
By the way Adjustable can not change the position of Grab Bar Body! Let's be careful.
So where is Adjustable?
Tail lamp and Blinker can be positioned back and forth.
In short, you can change the position considering Balance with Swingarm
(I misunderstood that Grab Bar could move (sweat) )
Moreover, the Bolt hole which holds the Tail lamp does not match the hole of Bracket of this product.
So I drilled Bracket for this product.
After all it will be less than an hour if installed normally,
It took me three hours with full of machining (sweat)
By the way, Frame of the mounting car body is AB 27.
Is it impossible to attach a pon to this car body?
Anyway it's expensive - Making is complicated - No machining and no good place!
Was this a difference in my senses, I thought if the bar itself was a bit thicker, it was pretty slim.
This is the difference of my feeling so I have not done it to MinusPoint.
☆ is two with Brand effect, Others is an evaluation saying nothing.
In this case it's good for Chinese (Lol)
View detail
Since it was worrisome from the time of sale, it had considered and purchased. Since the raw material is made of aluminum, appearance is also good and a form is very also a favorite. There was no place which it has by RIYA when the ZII tail which
Since it was worrisome from the time of sale, it had considered and purchased.
Since the raw material is made of aluminum, appearance is also good and a form is very also a favorite.
There was no place which it has by RIYA when the ZII tail which has come out from the manufacturer is attached, and it became [ since it was a car body with which it is not / free / capable of small sharp turns, ] easy when this glove bar was attached, and moving.
Moreover, since a price is very also handy, when a ZII tail is attached, it becomes an article I want you to attach simultaneously.
View detail
When purchasing the short tail lamp stay of G craft, it purchased together. Since it decided that the short tail lamp stay of G craft was purchased although the smart club bar which suits 4L monkey is looked for, furthermore it wavered with Mr. Hayash
When purchasing the short tail lamp stay of G craft, it purchased together.
Since it decided that the short tail lamp stay of G craft was purchased although the smart club bar which suits 4L monkey is looked for, furthermore it wavered with Mr. Hayashi, I did here this time.
Affinity with short tail lamp stay is also well (since it is the same manufacturer, it is natural) simple, smart, and very pleasing.
View detail