Reviews
StylingUp and Improved usability
Styling couldn't be better.
However, the difference is Large because the OEMSeat is too comfortable, but the Cornering by the appearance and the load from the buttocks is much improved.
View detail
GCraft is as good as it gets.
I like it very much
Also, if the price were lower...
View detail
It's Wilde, isn't it?
I wanted a rugged Image, Wilde feel, so I chose this one, although it is more expensive.
A short Hexagonal Wrench may not be able to reach it.
It is my favorite as per Image.
View detail
It's a good look.
I am satisfied with the product exactly as I wanted.
It looked great and I couldn't stop looking at it!
View detail
Name Chain
To increase load capacity as much as possible, CenterCarrier was considered.
The CenterCarrier is also GCraft, as it is also equipped with a GCraft front carrier, to create a sense of unity.
The Plate area of Silver is quite large, so the impression you see changes at once and the Machine feeling becomes stronger.
The load capacity is said to be 1 kg, but there is room for maybe 3 kg.
The installation itself is easy, but be careful only to install and remove the bolt that attaches to the MotorcycleBodyFrame.
The Bolt is screw-cut so that it enters the Bolt at an angle, so if you do not do it carefully, you will break the screw threads.
OUTEX SteeringStabilizer is installed, but it interferes with the Handlebar when it is cut to the fullest, creating a dent. The surface finish is beautiful Silver, but it seems to scratch easily.
The system is compatible with the Mole System standard, so various bags can be loaded in a variety of ways.
View detail
Dirt-style Custom
It is easy to install. It is easy to install. It is the perfect item to distinguish yourself from others. View detail
The impression changes by a Large amount, and there are a few points of concern.
[How is it used?
I bought it to change one of the areas that I didn't like the look of the NORMAL DAX, and the change together with the Rear fender-less and Exhaust System has changed the impression considerably.
Was the one you received as per Image?
I am satisfied with the texture as per Image.
Was the installation difficult?
The installation is so easy that even a beginner like me can do it with a small one-hour job.
However, you must read through the Instruction Manual. This is because the position where the Fender is to be installed 10.5 cm from the bottom edge of the Outer tube. If you do not look at these parts, you may end up with unintended results.
How was your experience with it?
It was quite nice to be able to install Inner Tube's Guard-like Parts, etc., using the Bolt holes that removed the OEM Fender.
[Included Parts:were they on?
Instruction Manual is included.
[Was there anything that disappointed you?
The brake hose guide comes with an extension part that prevents the hose from interfering excessively with the Up Fender, but it still interferes somewhat, and the color of the black hose is transferred to the Fender.
It is a moderately priced product and would be better if this area could be improved.
【Review】
I have written a lot about it, but I am generally satisfied with it, except for the cosmetics.
I don't run in the rain, so I'm not sure how much it would change the practical aspects of the product, but at least as far as looks go, I don't think this is a product that would betray anyone who is considering making Up Fender.
View detail
Hurdle is a bit high for a beginner to install, but the Rear area is quite Refreshing!
[How is it used?
The front and rear fender area of the DAX125 was heavy, so we installed a rear fender-less system in conjunction with the exhaust system replacement.
Was the one you received as per Image?
I am satisfied with the texture as per Image.
However, the fact that it has a reflector and the number angle conforms to the new standard was the deciding factor, so we decided to go with this one, even though it is a little expensive.
Was the installation difficult?
The installation itself is easy, but I thought the process of removing the OEM Fender was a bit of a hurdle for a beginner like me.
It was especially hardMODE to remove the OEM License Plate Light from the OEM Fender cover in order to use the OEM License Plate Light.
(I couldn't figure out the Coupler, so I ended up cutting a piece of the OEM Fender cover to separate the License Plate Light from the Cover.)
How was your experience with it?
After looking at Fender Eliminator Kits from various manufacturers, I decided on this product, and I think it was the right choice because it looks the most refreshing.
(However, if you bend down to look into the Bolt, you may be a little bit surprised by the number of Bolts.)
[Included Parts:were they on?
There was a Mounting Instruction Manual.
[Was there anything that disappointed you?
As a disappointment or request, I thought it would be new if the Instruction Manual included instructions on how to remove the OEM Fender.
The removal time was about three times longer than the installation time, so the Instruction Manual for the installation would be more useful.
【Review】
I have written a lot about this product, but I am very happy with my purchase.
Personally, the three things I did not like about the look of the DAX125 were the Exhaust System and the front and rear Fenders, so I was determined to purchase only those three items that I was absolutely satisfied with.
The License Plate Light is hidden inside the Fender, making it quite Refreshing, yet the Number angle conforms to the new standard, so it is a good product that does not make you feel guilty.
View detail
Use with Endurance Rear Carrier
I was able to install this product with the Endurance Rear Carrier installed. If anyone is considering using this product with the Rear Carrier as well, please refer to the following ….
Quantity:Pair (for Left and Right) The bolt supplied with this product is M8×35 and the bolt supplied with the Endurance Rear Carrier is M8×50, so when installing both, it is better to extend the bolt by 5mm or more, so the M8×60 bolt purchased at a hardware store was used. The torque of the bolt is 24N-m, which is stated in the instruction manual of the Rear Carrier, so make sure to tighten the bolt firmly.
The maximum load weight of the Rear Carrier is 8 kg, so the weight of this product (Quantity:Pair (for Left and Right) I think it can carry about 6 kg, taking into account the weight of the bag (about 2 kg in the case of the "C").
View detail
high-class item
I think the product is worth the price.
The texture is a very high quality surface material, you can tell the difference by the feel.
It feels no different than OEMSeat.
The seat feels a little hard at first, but after using it, it is moderately nice and firm.
Design would be a little thinner in my opinion, but I guess it is difficult to ensure a comfortable ride!
It is a product that does not hurt my buttocks so much!
View detail
The non-gussied up design is GOOD!
The Grab Bar by DAYTONA that I had been using up to now was not so bad, but I was concerned about the gills of the Fender Eliminator, so I replaced it with this one, which is a less protruding design. I was concerned about the gills, so I replaced them with this one, which has a design that does not stick out too much.
The sleek and clean design is perfect for the Fender Eliminator Motorcycle, and I am very satisfied with the large size.
It's easy to grab and go, and the performance is fine! Now if only it were a little cheaper.
View detail
Gcraft
There are only 2 sizes available for this sticker. Bought this for 2nd time. My bike already full of stickers so I stick it on my car windscreen. Looks unique. View detail
Mini stickers
Quality of the stickers are good and just nice for the size. As usual, such small items can be shipped by small packaging to save costs instead of the standard box unless you buy few items together. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Recommended products
It was used during Conversion to 12v.
Material:Aluminum and lightweight w
I bought it because I wanted to be concerned about what I couldn't see.
I like it, although I am disappointed that it is not engraved with GCraft.
The particularity is that you can see a little when you look into it.
The glimpse is intriguing.
View detail
Exclusive sticker
I bought few G craft items but no stickers included. As such, I have to buy separately. Quality is very good but quite costly. View detail
Fits: HONDA MONKEY R, HONDA MONKEY, HONDA DAX, HONDA XR MOTARD, HONDA CHALY, HONDA BENLY , HONDA APE
G-Craft M6 Reverse Nut
About quality and texture It's great. About the feeling of use The quality was good, and there was no problem installing it Products to buy together M6 bolt , m6 nut Difficulty of installation easy Cost performance and comparison with other products The price is a little more expensive than other companies, but I believe it's G-craft, so I'm satisfied with the purchase About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing There was no problem installing the blinker because of this item View detail
G-Craft M6 Washer Large Outer Diameter
About quality and texture It's great. About the feeling of use The quality was good, and there was no problem installing it Products to buy together M6 bolt , m6 nut Difficulty of installation easy Cost performance and comparison with other products The price is a little more expensive than other companies, but I believe it's G-craft, so I'm satisfied with the purchase About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing There was no problem installing the blinker because of this item View detail
G-Craft M6 Washer Large Outer Diameter
About quality and texture It's great. About the feeling of use The quality was good, and there was no problem installing it Products to buy together M6 bolt , m6 nut Difficulty of installation easy Cost performance and comparison with other products The price is a little more expensive than other companies, but I believe it's G-craft, so I'm satisfied with the purchase About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing There was no problem installing the blinker because of this item View detail
This can also be installed on Single Body.
I bought it to fill the empty space under the seat on the Right Side of the car body, which was left open because of the Other Brand ProductExhaust System.
The empty space can be filled with an oil catch tank, but the side cover looks more refreshing.
Incidentally, this Side coverSingle Body can be attached to the car body.
As you can see in the picture, there is a lot of interference when using the Lowrider SeatBracket, in which case you need to somehow insert the side cover inside the Seat Bracket, or shave the side cover.
View detail
To Accent of One point!
[How is it used?
I bought it to make it One pointAccent for Cowl and Frame.
Was the one you received as per Image?
The size was a little larger than I expected, but it was not so when I put it on.
Was the installation difficult?
It is easy to degrease and paste.
How was your experience with it?
It became Accent at One point, but it was a bit overshadowed by the Red land.
[Included Parts:were they on?
There was nothing.
[Was there anything that disappointed you?
Not particularly
I don't think it's a good idea to put too much sticky stuff on it, so I'm only going to use one point.
If you don't install GCraft Parts together, you will only get StickerTune! (Lol)
View detail