Reviews
Genuine G-Craft Suspension Hools (stand bobbins) for Honda Monkey 125
Whilst I was ordering the clutch cover for the Monkey 125, the customer asked to order a set of these stand bobbins too so it would be easier to work on the bike. Not a problem and super easy to find. The cost is ridiculously low and for what you get for your money a cool. Witht he other parts in my order, I got them all shipped together to save some funds and were all delivered in 5 days. The stand bobbins came in the shrink wrapped packet and were well presented. These do come in 2 parts so are pretty straight forward to fit together, then it is just a case of bolting to the bike. The quality of these look awesome and do look like they will last a fair while. I did have my doubts with the small bolts but they do seem to hold up well. No issues there. Very pleased with how they fit sand how easy they are to install. Thanks Webike View detail
To change from L-Type to U-Type receptacle
Purchased to change from L-Type to U type nut. The installation work itself is simple, but the nut holes are gapped because of the load applied when the pure STD nut is removed.
When installing this product, Jack or lifting force to lift the vehicle body is required. After installation, maintenance stand work is safer.
The gap between the ground and Tire is about 55mm with AstroPROducts MiddleRear stand.
View detail
They Do Offer a Much More Stable Platform to Work on the Monkey 125
About quality and texture: I am happy with the quality of the suspension spools from G-Craft. The spool is made up of two parts that are secured together with the included fastener. The material used is aluminium with the black surface being anodized and the silver surface being a raw finish. About the feeling of use: I find these spools a useful addition when working on the Monkey 125 from cleaning and lubricating the chain to stabilizing the rear end to allow the front end to be lifted to remove the front wheel. Products to buy together: Some lifting hooks for your rear servicing stand would also be desirable to purchase alongside the suspension spools. Difficulty of installation: The process to install takes about 10 minutes. Remove the OEM Honda rear shock nut and install and torque down the silver part of the spool and then install align and tighten the black part with the included fastener. Repeat the process for the other side. Not difficult to do. Cost performance and comparison with other products: High costing but you are getting quality materials and finishes with this product at a higher price as compared to the stainless steel option available on Webike and the even cheaper quality option available elsewhere. About shipping and packaging: Sea frieght is my preferred method of shipping due to the lower cost and it is fantastic that it has returned as an option once again so I can put my money toward parts and not high shipping costs. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: You may think these suspension spools are not neccessary but they do offer a much more stable platform to work on the Monkey 125 then just using the platforms on the rear servicing stand. View detail
Too cost-effective, but if you want to use RightSide Stand, is it possible?
It was somewhat cheaper on Outlet and
I use this GCraft Side Stand, so I had an extra OEMSide Stand to Order!
The RightSide Stand is a good fit for the CT110 HUNTER CUB & omega;
The product itself is Black PaintingSteel and can be installed with no problems and no dimensional deviations
One point is that it is easier to position the Footpeg Mounting Bolt by pulling out three bolts, loosening one bolt until it is just about to come off, and then temporarily tightening one bracket and collar before removing the bolt.
Collars are long collars on the front two sides of the body
The two back side of the car body are fastened with short collars
If you are diverting an OEMSide Stand as we do
The screw groove cut at the back of the Side Stand must be penetrated with a Φ10 steel drill.
Was the GCraft made without Screw grooves?
When we changed the LeftSide Stand, I think we were able to go straight to the LeftSide Stand, but we don't care about irreversible processing, so we just quickly changed the Drilling
Easy to install outside as long as the hole is widened
It's a long-awaited RightSide Stand conversion.
Because of Left Side traffic, there are quite a few situations where LeftSide Stand is difficult to produce because of the Left slope.
I think the opportunities for use are there.
View detail
g craft gc 019 frame
awesome frame with incredible shape ! I was needed a +3 frame to fix 12" wheels with takegawa desmo engine. You can follow the build on instagram @ghislehun many thanks to webike View detail
Rear Suspension Hook from G-Craft
* About quality and texture, A two part hook machined from aluminium. Extremely light weight but also very strong to take the weight of the motorcycle when the rear maintenance stand is used. * About the feeling of use, Having these hooks fitted to the rear suspension lower mounting points does not stand out or draw attention which allows then to retain fitted at all times readly for when the rear of the motorcyle requires lifting. * Products to buy together, If you are one that loves looking after your own maintenance then also add the front stand hooks to your order also and that way you'll be covered for any future maintenance. * Difficulty of installation, Installation from simply removing then rear suspension lower mount nuts and replacing them with the hooks that thread on. The process was completed in 15 minutes with no difficultly. * Cost performance and comparison with other products, There are cheaper options from other brands but I was happy to pay the extra dollars for a well designed part and to pair these with my other G-Craft billet parts. * About shipping and packaging, I am happy to wait 6 weeks on average for my parts to arrive in Sydney Australia via Webike's sea freight which comes with tracking and insurance so I know I'm covered in case something was to go wrong but with there outstanding bubble wrapping and boxing there have been no problems. * Any concerns, cautions, or advice when purchasing, Webike have this same part for almost half the price from H2C G-Craft if you are happy to wait 6 weeks for stock to arrive. Use the product reviews to assist in making a decision on your purchase. View detail
That's a GCraft
As expected of GCraft, the accuracy is fine and the STAND fits without any interference.
You can adjust the stand holder to avoid hitting the swing arm when you raise the stand, which is a common problem with modified monkeys.
View detail
Suspension Hook
About quality and texture - Excellent quality, the modular part fits together perfectly and has a really nice surface finish. About the feeling of use - Works great together with my paddock stand but the surface finish has become slightly damaged from the steel hooks. Products to buy together - These pair nicely with the G Craft billet chain adjuster, product # 31263. Difficulty of installation - Easier then easy, remove the rear shock lower nuts and fit. Cost performance and comparison with other products - This part is expensive but I did not see many options available and I needed a way to raise the rear of my motorcycle safely for maintenance. About shipping and packaging - When EMS shipping is available it is cheap and arrives in about a week so no complaints and arrived safety with plenty of air pillows for protection. Any concerns, cautions, or advice when purchasing - If you are in a rush for your part make sure to check the stock level and even message Webike for a delivery date estimate as these seem to be lower in stock most of the time. View detail
More rigid than I thought!
There is an inexpensive domestic one, but it was expensive considering the texture and the accuracy, but it became GCraft.
It's a large, beautiful piece of work, and it installs Exactly the way it should!
I was very worried about the price of the dress-up, but I was very happy with my purchase.:By connecting the engine to the frame from the bottom, the engine vibration is reduced and the running feels more stable.
Large pleased with the look and the unexpected effect!
View detail
Relatively expensive
I have searched for a lot of related products, most of which are only silver, only g-craft has the black color I want, but the parts of this brand are relatively expensive View detail
Feel normal
Because many of the related parts of xr motard have been discontinued, so there are not many related products to choose from, but relatively speaking, I think it is relatively expensive View detail
After some DIY, I managed to get a piece of the action, but
Previously on & omega;
It's too good to throw away, so do-it-yourself measures
The rattling thing is a recessed OEMSTAND 12.4mm wide. This one is 12.5mm wide.
So we ordered Stainless Shim inner diameter 12mm, outer diameter 22mm, and thickness 0.1mm.
Bite into this stuff and it's perfect.
I ordered 0.05mm, 0.02mm and 0.01mm just to be sure, but they're out of stock & omega;
Also, you should definitely have a spring hook.
Even a cheap one is enough for me, so I'll keep it & omega;
It's a full-powered tool and I'm afraid of substitutions.
STANDBolt/Nut is 14mm/14mm
Side stands sensor fixed bolt is 8mm
Too short All Screw, Order M12/P1.75 inch cut Stainless bolt 110mm for extension
The Uniqlo length NutM12/L60 on this one.
I couldn't find a good one around L60 in Stainless Steel length Nut, so I used Uniqlo ω
Also, the M12Stainless Nut 3 different thin 1Pack
The rest of it will be on the rubber board for about 1,000 years. It's a useless cost, but it's unavoidable.
I decided to temporarily connect them with a long nut for 30mm each, and then fill up the all screw of the body with 30-35mm
I used a disk grinder to cut it down to 32mm.
It's adjustable, so just use About.
Then, put two nuts in the bolt for the double nut, put the body cut with a long nut and tighten it up.
Also, the angle of the STAND toe is poor, and it's only grounded on the inside of the STAND only.
So I put it on the Rubber Board Teketo and it's done
Well, I've managed the Large goal of somehow improving my over-sleeping OEMSide Stand.
I'm not happy with some of the details, but it's good because we achieved the minimum objective.
Just not for people who can't do DIY;
View detail
Looks good, reduces vibration.
Polished by Gee CraftBuffing as expected!
Texture, accuracy, no complaints.
In addition to that, the vibration caused by the Engine has been reduced!
The position of the oil cooler was changed under the engine head because it was Necked.
The price is A little high, but I am satisfied with the product.
View detail
Staggeringly desk-bound product
First things first.
Unless you're a pro with some degree of do-it-yourself savvy, there's nothing you can do about it.
If you're looking for a way to stay in place and say, "Hey, turn around!
First of all, I can only assume that whoever made this thing didn't actually use the CT125 CT110 HUNTER CUB.
If you try to ride a little bit, you shouldn't realize that the Side Stand angle is too much for you to sleep on, …………
It's a fatal point of the Uli's Adjust function. The Stainless SteelAll Screw is turned to adjust the length of the side stand, but even if the length is set to Large, it's only the same length as the normal side stand.
It is possible to adjust the side stand which is too much sleep to make it lie down further, or Level which makes you doubt your sanity.
I'd love to hear what they made it adjustable for.
Furthermore, I tried to install it, but the opening of the upper recess on the Side Stand side was too large, so I tentatively assembled it, and it rattled ……………
We're running out of time.
I think that it can be managed by procuring a Washer or Spacer that fills the gap between the rattling, or cutting a hole in the aluminum plate if it is made to be used somehow. hellip;……… …
As for the height, in case you're wondering, STAND's feet are wide and have holes in the four corners.
If I can get a hard rubber board of the height you want to earn and drilled and bolted it up, I can make it work, but …………………
I feel like I've been grabbed by a hell of a HaGap for the first time in a long time.
I think you should have at least a countermeasure Washer in the package ω
If you have any intelligence, you should extend the All Screw section a few more inches now.
I'll report back when I've done the DIY.
View detail
I wish I'd bought it sooner
I used to use the OEM STAND, but the height of the car changed slightly by extending the swing arm and replacing the Rear Suspension and replacing the tires, and the body of the car was collapsing and waking up too much. Once I put a STAND that was a little shorter than OEM, but the body collapsed too much and I had to return to OEM after all. But when the car was too much, it was difficult to get it to fall down with the slightest tilt of the ground.
I've always wanted this product, but I was hesitant to buy it because of the delivery time and the high price. However, when I inquired, I found that the delivery time seemed to come in sooner than advertised and I thought it would be more expensive after it collapsed, so I took the plunge and bought it.
The result of the purchase is Large satisfaction. The length can be finely adjusted, so I don't have to worry about customizing it in the future. I should have bought it earlier.
STAND is Material:Because it is aluminum, the powder of aluminum falls on the place where it is placed, but I don't care about it.
View detail
Image change!
What made you decide to buy?
Longing for the Parenthesis of Racing Stand Hook I switched from OVERSwing Arm to G-CraftSwing Arm! These are the Parts I've been wanting to put on...not on the Overswing Arm! It's one of the Option Parts
How was your experience with it?
The manufacturer's recommended STAND is a combination of the J-TRIP Racing Stand and a durable plate holder The manufacturer recommends the combination of the J-TRIP Racing Stand and the durable plate receiver, but currently, the AP Racing Stand and the plate receiver are recommended I have been patient with the StandL receiver and have been using it as I have been I can't wait to try it out to see what it's like
Was the installation difficult?
Degrease the Racing Stand Hook installation part and apply medium strength screw lock agent to it G-CraftSwing Arm manufacturing accuracy It is easy to install due to the good quality of the
What is the point or hang of the installation?
When purchasing G-CraftSwing Arm, you will have the option to choose the Chain Pull option Standard Type (Racing Stand HookSpec.) or the G-CraftSwing Arm When you select the Racing Stand HookSpec. OWTypeChain pull Racing Stand Hook can be installed No Stand HookBase is available
Do you have any wishes or suggestions for the Manufacturer?
Currently, we only have the Racing Stand Hook in Gold and Red Blue is also an attractive color, but it would be nice to have a choice of several more colors Also, it would be nice if you could sell the G-Craft Racing Stand? I think it would be nice if you can sell the G-Craft Racing Stand?
[Do you have any products to compare it to?
Option for G-CraftSwing Arm purchase:Racing Stand OW of HookSpec
and Stand HookBase (M6)
View detail
Too bad about the packaging!
The moment I got it in my hand and opened it Hmm? It was
The packing material is just wrapped around the Frame It was out of Frame
The Bolt part of the Frame to receive rear shock? The ball is designed to ground directly to the bottom of the ball, and if you want, you can turn the ball into a Penetrating
When the box was placed on the floor, the impact and load seemed to be thumping against the Frame and Bolt parts
Is this the kind of packaging on the Manufacturer's side, or are the packers terrible?
When I traded second-hand goods between individuals in certain auction sites, I didn't see many items that came with such terrible packaging It is not
It's not a cheap purchase, and it's a quality control thing, so you want to make sure it's done right It is
View detail
I'm glad I bought it!
It was helpful to be able to share the STAND with a Large Motorcycle I thought I would have to buy the receptacle as well, but I found some good Parts and they came in handy Easy to install too! View detail
adjustable stand
very nice quality from gcraft as always, but the price is very high i hope gcraft can lower their price down a bit will be more buyer View detail
It's expensive, but a boon
Hook on to the Swing Arm for Mini bike
Rubber type STAND says
In the case of this MONKEY125, the
The Swing Arm is very slippery because of its oval shape
and the paint peels off easily
The anxiety factor is Large, and every time I work
I didn't want to see the scarring grow
I finally bought it
The size is larger than I imagined, but it's more noticeable than I expected
I think it's a good way to feel different
The Instruction Manual strongly recommends the use of screw inhibitors
Creating Parts that are structurally prone to loosening
We're in a location where there's a lot of vibration
If you are about to wear it, you should be careful
Whereas the Cap Nut that fastens the lower part of the OEM rear suspension is 14mm
This product has a 19mm nut
To be able to manage torques when wearing them
It's a 19mm deep socket and glasses, but it's torque-managed
I suggest you buy tools
View detail