Reviews
Not attached to Rear Sets!
The SPG force is a little stronger than I expected, and it takes a lot of force to step on the pedal until the RRBrake locks, but the controllability is improved by a LARGE amount compared to without the spring. It is a very simple part, but I would have been happier if the spring force could be selected for the parts that affect the Control system. View detail
Excellent
Hello everyone, this is a good product and I recommend it to everyone. This product can play a better role in braking .This is 100% original, you can buy with confidence. View detail
Rear brake can be used with peace of mind.
When we replaced it with Rear Sets, we could not install a return spring, and we were not sure if we could install a return spring, so we installed a return spring like GCraft's Rear master.
Now you can use the Rear brake with peace of mind.
View detail
Fits: HONDA For Nisshin Rear master for NSR50
Almost Dress-up parts
Functionally, it is almost like a dress-up part, although it has the feel of recoil since it has a Spring.
This is a rather lonely area, so it feels like something is being added by making it more bulky.
View detail
Fits: HONDA For Nisshin Rear master for NSR50
Easy to install
Nut in the second photo is not included.
Adjustment Dial is a transparent plastic Screw
Please be careful not to lose it, as you will be saddened if you lose it.
To be honest, there is no problem without it.
To be clear, we hired them based on looks alone.
View detail
It could be stronger.
I installed it because I could not feel any reaction force in the rear brake of 250SL and it was difficult to control.
It's better than nothing, but the spring is weak and needs to be stronger.
I installed it because I had no choice, but the price is rather high for the color and spring.
However, I can now feel Pedal's treadmill and Fee Ring is better.
View detail
Exactly to the 6cm Long G-Cla Swing Arm of DAX.
I attached it to DAX's 6cm Long G-Cla Swing ArmSpec.
Before this product, I used to install the same GCraft 14/16cm long wheel, but it was too long and I had to pass the brake arm beforehand to remove and install the rear wheel.
This was very annoying and I wanted a third hand.
With this product, even after the Wheel is fixed to the Swing Arm, if the Torque rod is free, it can be fixed to the Brake Arm.
It is possible to pass through, so the serviceability has been improved remarkably.
In the explanation of using for MONKEY for DAX on the HP of the manufacturer, it became suitable for 14/16cm long, but
The 8, 10, and 12 cm Long's are much easier to use!
View detail
I installed it without bending the ROD to adjust it!
I am Tanaka Shokai (TANAKA) I installed Tanaka Showkai Rear Sets Kit B. In that case, RearBrake Rod needs to be bent and processed, but this Brake Rod was able to be installed without processing.
If you have the same spec. as me, why don't you use this ROD as a reference image and choose a ROD that you can attach without any processing?
I can't be responsible for that, but…
View detail
GCraftBrake Rod
I purchased this product due to changes in Long Swing Arm.
Compared to OEM Product, it's just a stick to fix.
It would be helpful if you could do one more thing.
View detail
I replaced the Brake Rod of DAX.
When I bought a used GCraft Swing Arm for my DAX.
It seems that the Brake Rod that came with it was the length of the Rear SetsSpec.
If you don't adjust the angle on the Brake lever side, the ROD will not be long enough.
I had it for about 2 years and now I bought a regular length ROD and replaced it.
Because it is a regular length, the width of the adjustment of the treadmill, etc. has become large, but
When you remove the rear tire and put it back together, it is difficult to put together the connection parts between ROD and Arm.
It became much more difficult.
If you make it right around the middle of the length before replacement and this time, it will be just right.
It is not so expensive Parts and I would like to replace it again if I have a chance.
View detail
Installed on NSR250Rear master
It is not so difficult to install. However, in the case of my motorcycle, I also adjusted the stop-lamp switch. The effect is not as good as it should be, but it is very nice to look at. View detail
Good product
The feeling of stepping on the rear brake became a little harder and personally improved. Until now, there was not so much the feeling of stepping on Pedal at the bottom of Boots, and it was difficult to adjust it, but now it is possible to control it a little. View detail
Fits: HONDA For Nisshin Rear master for NSR50
Brake Spring M/C
Top notch quality and perfect fitment which is expected from this company. Wasn't sure on fitment due to the M/C being a universal fit but well worth it in the end. View detail
Fits: HONDA For Nisshin Rear master for NSR50
Spring Processing!
A little bit of spring processing is needed, but I was able to use it for GROM! The included Spring is long enough for the GROMMASTER, and when Spring is close to the line, the Rear Be careful, the brake will not work! So cut the attached Spring to 2 1/2 volumes and the remaining Spring will be 3 1/2 volumes Check the two and a half volumes of Spring that I cut earlier to match MASTER Confirmation! It became a satisfactory spec. After adjustment and confirmation, the bottom of the cut spring top and bottom Cutting to Flat with Belt Thunder Why do I shave it to Flat? It's a bit of a process to blend in A little? Spring processing is required for JC61-1300001 to GROM's Rear Master got better at parenthesis! (Reference is at your own risk) G-Craft:Brake Spring for Before purchasing Adjustment Type Rear Master, you should check out their Rod I had arranged for the endAluminum BilletMASTER end (Red) I had a lot of trouble deciding on the colors for the combination, but it was a fun time and the result was The moment I saw GROM, I felt more attached to it View detail
Fits: HONDA For Nisshin Rear master for NSR50
Great little one
First I thought this item is just for show. But when I order this little one and install it then I've found it very useful when you use your rear break View detail
if you have bad pedal return after footpeg conversion, this is it
I replaced it with Striker's Rear Sets
I had a situation where the brake pedal would not return
Pedal returns with Spring connected to Stop-lamp, and
This seems to be the mechanism, but Spring is too weak
Stop-lamp is always on, and
PedalFeel was diluted, so I added this one
The pedal return has been properly improved
I can now feel the Feel of the Pedal more firmly, too
It was the right thing to buy
But the Conical Spring isn't that expensive if you look for it
You can also pinch the collar to prevent height and spring dropout
With some ingenuity, I thought I could get the same effect for less money without buying this product
View detail
Fits: HONDA For Nisshin Rear master for NSR50
Great little product
Great looking and great built quality. Awesome little product. I would happily suggest to get this. Mine was gold and the colour is also good. Makes the brake pedal feel little bit better than without spring, IMO. View detail
A little texture is left in the base material ....
10 cm Long Swing Arm with Rear SetsSpec. I mounted it in.
Since I feel a little texture in the base as it is, I use Plating after Buffing.
Performance and function are truly GCraft's.
View detail
Fits: HONDA For Nisshin Rear master for NSR50
Hi all, This product is of the highest quality and finish, fits and works great. I would highly recommend this item to anyone.
Hi all, This product is of the highest quality and finish, fits and works great. I would highly recommend this item to anyone. View detail
Quality is truly.
I use it for Tank reply Rear master made by Nisshin.
Accuracy, quality is one word of Mr. G Kuru, but the price is - - -. (Bitter smile)
G Kuran We think that you can sell more if you lower the price a little more.
View detail