Reviews
Fits: YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ250F, YAMAHA YZ450FX
I purchased this product because I plan to replace the exterior.
I can't say for sure since I haven't received the exterior yet, but it looks solid, thick, and sturdy.
It seems to need some hang to paste, but I guess it's not a problem since forest roads and Enduro are Main.
View detail
Fits: YAMAHA YZ250, YAMAHA YZ125, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ250FX
Not yet installed...
It is thick and firm. I wonder if it needs some hang to stick. View detail
Good looking stickers
Looks great, thick and durable, bonds good.Doesnt get scratched easily.highly recommend this. Easyl install,Cleaned surface of forks where these were to be applied and visually aligned the print applying the center as I held both ends back with one hand. Once the center made contact and I was satisfied the alignment was good I began pressing from the center up and down the full length of the decal to assure no bubbles were being trapped until one half was fully attached. Then worked from center again the other direction until it was fully wrapped around fork.Repeat on other side. View detail
great seat cover
seat cover fit great and loops over each end of seat for easy installation. No matter how much stretching and how many staples I used, there's a couple wrinkles.The color looks good, but doesn't match OEM. It's a little darker.Lots of grip ! It took a couple days at the to get used to it. Night and day difference from stock.Use 6-8mm staples when you install or else it doesn't stick View detail
Swing Arm Decal
Used on MD47RLY50. Easy to apply.
It is thick and seems to offer good protection.
OEMDecal's Tricolor color and
I think it is good to match and have a sense of unity.
Front fork is also available in the same design.
Will HONDALogo feel like a traffic jam?
View detail
Grip is amazingly durable!
[How is it used?
This product was stuck on an XR250 Seat that was purchased used by a person at work about 15 years ago from the beginning.
The vehicle had been restored to the best of my ability at that time because the exterior of the vehicle was damaged except for the Seat, and after many years it came to me a few years ago.
The exterior of the car was damaged by ultraviolet rays, and the tires were badly cracked and the brakes were sticking to the car.
Sorry for the long preamble, but even in such a state of exterior rustling, only Seat remained flexible.
The surface had lost its Luster due to water stains and dust, but after washing the car and applying a protective material, it returned to the condition it was in 15 years ago.
It is indeed a product sold by Webike for 10,560 yen, and is definitely more durable than the OEM Seat Cover.
How was your experience with it?
When the car came into my possession, I again did Restore maintenance on each part of the car, but I drove it for a while without reupholstering the Seat (I eventually replaced the Seat Cover with another Manufacture's one to match the repainted exterior).
GripperMaterial that "Demonstrate Exceptional Flexibility and Grip Power" as the manufacturer's slogan says, is used throughout.
Assist Rider's Machine Control. The flexibility and gripping power did not deteriorate even when exposed to ultraviolet rays, rain, wind and dust.
How did it compare to other products?
As I mentioned above, I had replaced it with a Dimple-finished Seat Cover made by another company, but the Seat Cover remained as flexible as a new Seat surface after more than 15 years. I think it is phenomenally Tough.
[Points to note]
Not so much as a warning, but the moat on the Seat Cover named GripperMaterial was deep, and if the Seat was bathed in mud, the dirt would get into the deep moat and be difficult to remove.
The product is three-dimensionally sewn for XR250 (MD30), so it is relatively easy to work with if you have experience in Seat reupholstery in the past.
Other items that would be helpful
The deciding factor in the purchase
As I mentioned at the beginning, it was already stretched at the time of purchase on a used car.
[How is it used?
Basically, it is a city Main, and I am fully aware that it is a high-performance Motorcycle for a 4StDual PurPass car at that time, but I could not handle it because my feet could not reach the ground on rough terrain, and I lacked the skills.
【Included Parts:presence or absence】.
Quantity of 1 Seat Cover and Instruction Manual on how to apply.:Set
I don't think there was a tandem belt attached.
[ITEMS TO BUY TOGETHER
Seat fabric to fasten to Seat Base seat. Tucker, a slightly larger version of Stapler. and short-legged core.
The fabric joints are crimp type like OEM, so there is no slippage, I think Coking agent is not necessary.
Opinions and requests to Manufacturer.
An indispensable manufacturer in the off-road motorcycle world.
We look forward to your continued development of a wide variety of lineups.
View detail
FACTORY EFX Seat cover ALLGrip
crf250lmd47OEMSeat cover had a tear and I replaced it with Other Brand Product because I had to. I bought this product this time. The shop said that the Seat fabric was hard and sometimes tore when pulled and tucked. Still, I was satisfied with the beautiful reupholstery. Is there room for improvement in the quality of the fabric? View detail
The color match is narrow, but it’s okay.
It is not difficult to attach, but you need to be careful about the location when attaching. Since it is generally thick, the fork cover's role is also high. And it's cool View detail
StickerTune staple of Swing Arm
I plan to replace Sprocket later, so StickerTune first. View detail
CT110 HUNTER CUB as Decal
Purchased as Decal for CT110 HUNTER CUB. I didn't expect CRF for Swing Arm to be Exactly.... I put it on after I fixed it with masti because it is divided into 3 parts. It looks good. View detail
Cut and feel good
I bought this one because the original decal had peeled off due to aging and deterioration, and I also bought this one for dress-up. Cutting was easily done with a 100-yen craft knife. The product photo is not very kind. In fact, the SIDE Decal is reversed and the DUNLOP Logo is correct. View detail
For those who want to change the exterior Image.
[How is it used?
I purchased this product, which is cheaper than the OEM Decal, to refresh a slightly scratched Shroud and Side cover that I got used.
Did you receive the item as per the Image?
The thickness of the decal is firm and the durability looks promising, the gloss and design are good, and the product is just as in Image.
Was it difficult to install?
This kind of work is... more than difficult. "A tedious process." The feeling was so strong that it took me half a day to get there.
How did you like it?
The quality of the decal was very satisfactory with almost no gapping of the mold and high quality.
Because of the thickness of the Decal itself, there is no tearing or peeling after a few falls. (Except for falls on gullies, etc.) No complaints about durability.
The adhesive strength is high, and if it is applied firmly at first, it will hold up to high-pressure cleaners better than OEMDecal, so it is easy to use. (It is not absolutely impossible to peel off. Please keep in mind moderate spec.) Easy to wash the car after playing in the mountains.
As mentioned above, the adhesive strength is so strong that it can adhere even over scratches on shrouds and other surfaces without any problem, and the thickness of Decal itself makes scratches inconspicuous, making it ideal for concealing wounds.
Was "Included Parts:" attached?
Only Decal is taped to a cardboard to prevent it from losing its shape, so please peel it off before working on it in the mansion.
Were there any disappointments?
The thicker fabric makes the application work a bit large, but the hard work pays off when you see the finished exterior.
Other items that would be helpful
Point and hang of installation
Work slowly and unhurriedly in a dust-free environment.
Spray the backside of the Decal and the object to be attached with a mist spray diluted with a neutral detergent, and position the Decal and the object to be attached by displacing it, and then remove any air or moisture that may have entered between the Decal and the parts little by little.
I think it can be applied beautifully without wrinkles by applying heat to curved surfaces with a dryer or similar tool.
In advance on YouTubeetc. Motorcycle Decal Paste. You can work with even more confidence if you check out the video by searching for
[Availability and clarity of the Instruction Manual
Was there an Instruction Manual? Well, I don't think you need Instruction Manual if you watch the video before you try.
[Notes]
Object to be pasted (Shroud and Side coverretc.). The surface of the "P" should be degreased thoroughly before applying the adhesive.
[ITEMS TO BUY TOGETHER
Chemicals for degreasing (parts cleaner, silicon-off, etc.), spray bottles for misting, rubber spatula for degassing & dehydrating, etc., will help you to work smoothly.
[Opinions and requests to Manufacturer
Please reissue Decal for discontinued models only after a certain amount of orders have been placed.
View detail
Fits: KAWASAKI KDX220SR, KAWASAKI KDX220R
Parenthesis is so good that I can't keep it clean anymore...
[How is it used?
I have used the Graphic decal for WR250R before, so after checking with Webike to see if they had one for KDX220, I did whatever I could to get the money to get it.
I used it on the WR250R to refresh the somewhat scratched shroud and side cover, but this time I am buying it to use on the new exterior of the KDX220SR.
Did you receive the item as per the Image?
Like the Decal I had purchased before, it was thick and durable, and the gloss and design were just as good as the Image.
Was it difficult to install?
It is not difficult, but it has a strong sense of tedious work and also requires patience, so it takes more time than you might imagine if you are not used to it.
How did you like it?
The quality &design of the decal without any gaps in the mold is very high, and we are very satisfied with the result.
The thickness of the Decal itself makes it resistant to tearing and peeling after a few falls, but I felt it was a waste of space and could no longer play in the mountains with this exterior attached. (I'm poor.) 。
When we play in the mountains, we go out with used exteriors with cheap Decal attached to them.
Was "Included Parts:" attached?
Only Decal is taped to a cardboard to prevent it from losing its shape, so please peel it off carefully before working on it.
Were there any disappointments?
No, it is just my personal opinion, but I have no complaints about both the texture and design.
The thicker fabric makes the application work a little large, but when you see the finished exterior, the hardship of the work will disappear.
Other items that would be helpful
Point and hang of installation
Work slowly and unhurriedly in a dust-free environment.
Using a spray gun, spray a diluted solution of neutral detergent on the backside of the Decal and the object to be affixed, and position it while shifting it slightly to remove any air or moisture between the Decal and the parts.
I think it can be applied beautifully without wrinkles by applying heat to curved surfaces with a dryer or similar tool.
In advance on YouTubeetc. Motorcycle Decal Paste. You can work with even more confidence if you check out the video by searching for
[Availability and clarity of the Instruction Manual
Was there an Instruction Manual? Well, I don't think you need Instruction Manual if you watch the video before you try.
[Notes]
Object to be pasted (Shroud and Side coverretc.). The surface of the "P" should be degreased thoroughly before applying the adhesive.
[ITEMS TO BUY TOGETHER
Chemicals for degreasing (parts cleaner, silicon-off, etc.), spray bottles for misting, rubber spatula for degassing & dehydrating, etc., will help you to work smoothly.
[Opinions and requests to Manufacturer
We would be very grateful if you could reissue the models that have been discontinued in the past, once we have enough orders...
View detail
It is good!
I was looking for a Sticker because I like Michelin Tire, but I found an affordable one among many expensive ones!
I am wondering if I should put it on Motorcycle's Box or on the light.
View detail
Parenthesis good
Parenthesis good
I would buy again.
View detail
Anyone can put it up in three sections!
When ordering,
Swing Arm has a bumpy decoration, but I wonder if it can be applied neatly.
I was worried, but when I received it, I was surprised to see that it was divided into three parts!
Anyone can put this up!
The texture and design are perfect with Front.
View detail
The footwear is tightened.
ExactSize because it is Exclusive Design.
It is thick and has perfect adhesion.
It is easier to install the Left Side by removing the Brake hose clamp.
If you hurry, you can turn around. It is.
It can be done by anyone because it is just a matter of putting it on.
View detail
It was installed perfectly!
Mounted on Swing Arm of CRF250 Rally MD47!
If you are not careful, it will bend, but it is not that difficult.
White areas are dirty and should be cleaned regularly!
View detail
fashion starts with the feet
Buy for dress-up
Strong adhesion and no durability issues.
It is slightly Large and can be Cut.
View detail
Just paste Custom
We have used this product in the past, and its durability is top-notch. If you are applying it for the first time, it may be difficult to get air in, but it is a good idea to decide where to start and apply the first part first, and then let the air out little by little. It is a product that imitates the OEM color, so it fits MD47 perfectly. Some people have applied RALLY 50 OEM decal on the front fender, but I've already applied DirtFreak decal, so I'm not going to do that. View detail