Reviews
DID chain tool usage review
DID chain tools are small in size and very convenient to use.
The strength of the tool is very strong and reliable.
The method of use is very simple, so anyone can easily operate it.
It seems like one tool can be used for a long time.
This served as an opportunity to further increase trust in DID.
-------------------------------------------------- -------- DID chain tools are small in size and very convenient to use. The strength of the tool is very strong and reliable. The method of use is very simple, so anyone can easily operate it. It seems like one tool can be used for a long time. This served as an opportunity to further increase trust in DID. Powered by Google Translator
View detail
A vital tool for a specific task
Easy to apply the rim stickers with this tool. A couple notes- firstly; absolutely perfect application of the rim stickers was impossible for me. But it's close enough that I'm probably the only one who will ever notice. Secondly: wheel balance weights will obstruct the use of this too & a degree of freehand sticker application will be required, it's not difficult though. View detail
It's great that it's not difficult.
I thought Chain exchange could only be done at the Shop.
I nervously worked through the Instruction Manual and YouTube, and it was surprisingly easy.
Next, I have prepared a Chain replacement for GSX1300R HAYABUSA and will lend it to my friend.
If you use it for a few cars, it will be enough to pay for itself.
I'm glad I bought it... ♪
View detail
CBR1000RR-R uses this
The Rear Axle Nut of the CBR1000RR-R is 36mm in diameter.
The tightening torque is also high, and a box with many angles was used, but it seemed to come off, so we changed to a 36mm hexagonal box.
At the same time, I also purchased a pure STD Nut with it. I think I was able to buy peace of mind at a reasonable price with FirmlyFit. I think I was able to take countermeasures before I got injured, although I am satisfied with myself.
View detail
Even an amateur can replace the chain. (However, 27mm Glasses are required.)
Recommended Chain Replacement Tool for DIY.
Chain replacement tools range from those that cost 40,000-50,000 yen to those that cost less than 5,000 yen. To be honest, I was hesitant about the price because I use them very infrequently (maybe not even twice), but I was sure of their quality and the official videos on how to use them. I'd rather buy something for $4,000 and have it fail." I bought it with the feeling of
You can replace it without mistake by following the instructions as shown in the official video.
The point that I had a hard time was that there were no 27mm Glasses, so I used MONKEY as a substitute, which made it difficult to fix the body, which is important, and I could not use force, etc. 27mm Glasses are essential to fix the body securely. I will definitely prepare 27mm glasses next time I use it.
The 19mm turning side can be adequately handled by the Box and Ratchet Handlebar.
It is also good that the OtherParts are sold in bulk. I experienced the pin removal process for the first time, but I feel it is inevitable that I will make a mistake and bend it someday.
If you are going to replace the Chain yourself, I don't think there is an option below this (price), so I think the Cost performance is sufficient.
View detail
BIGSize！！
I use it to fix sub-computers, voltmeters, oil temperature meters, thermometers… and other electronic devices that I have installed in my car. It is easy to attach and detach, yet it is very strong! View detail
Easy to use
I'm going to use the gloves and I don't have to worry about changing the Oil. View detail
The uses are unlimitedLarge!
I used it to secure the sub-computer on my Ninja 250SL, but I had some left over so I used it on the screen door of my front door! The adhesive is strong and does not come off, yet it is easy to put on and take off! This is really convenient! I think it can be used anywhere as long as it does not get wet! It is easy to install because you just need to remove the grease and stick it on! It is the most convenient product! View detail
Yamaha tappet adjuster 3mm
Original YGP. Fast shipping 3 days from mailed date to Singapore . Package bubble wrapped to ensure no priduct damage during shipping. View detail
It worked for the 3rd generation GSX1300R HAYABUSA.
I'm not sure if it's necessary to use a 14mm socket wrench or not, but I'm sure it's a good idea to use a small tool for the GSX1300R HAYABUSA in order to keep it in good condition. View detail
Just right for Large Motorcycle
I think this size is necessary for Large Motorcycle riders. View detail
It is considerably less expensive than OEM but functions well.
O-ring for Generator of CUB series.
It is cheaper for Large than buying OEM. At least as of this writing in May 2024, OEM costs about $340. OEM is getting expensive….
It is just an oil-resistant O-ring, but surprisingly, there is no general standard product, so we have to rely on OEM or compatible products.
I'm basically a reuser of O-rings here. Bought just in case at OH." But after a while after OH, it started leaking and I had to use it. This kind of leakage is scary because it comes out of nowhere even though it looks fine.
After replacing it with this product, it is functioning without any leakage at all.
It is just an O-ring, so there is nothing special to say, but be careful not to twist it when installing it. If it twists, it will break and leak.
An old ring is hardened and oil is absorbed, so it is difficult to twist even if it is attached properly, but a new ring will twist.
Once oiled and installed, the twisting can be fixed by inserting a thin, non-sharp stick such as GlassesDriver between the groove and the Ring and turning it around.
Anyway, it is better available and less expensive than OEM, so if you have an old CUB-type Engine, I recommend you to buy it while shopping on webike.
View detail
![[MOLYGREEN] Oil Change Poi Box](https://img.webike-cdn.net/catalogue/images/118721/01_TS.jpg)
This is my first purchase.
I purchased it for the first time.
The Large size and the height of the box were just right for 50cc and Smooth Oil change.
The only drawback is that it does not come with thin gloves for replacement, which must be prepared separately.
View detail
Good and inexpensive.
All waste oil treatment Boxes are the same.
That being said, it is the same, but this box even comes with Vinyl gloves + Tie Wrap for oil changes, so it is better than the others.
Other basic functions remain unchanged.
View detail
Good!
As expected of KOKEN.
I am satisfied with the texture of the Anodized that I requested . (^o^) /
Since it is anodized, we can only request aluminum products, but we asked Pinpoint to anodize the parts and bolts that we wanted to add color to.
The color I requested is Pink.
There are many Anodized products in the world, such as Blue, Red, Gold, etc., but there are almost no products in Pink color. (Polish)
But thanks to this, we were able to create a nice dress-up look that was not similar to other people's.♪
View detail
Ideal for NAKED's Engine area!
As per the Title, it is ideal for cleaning around the Engine of Naked motorcycle!
I have been driving a GSX1400 motorcycle for 16 years. The front side of the engine is hard to clean because of the oil cooler, exhaust pipe, oil line, and oil filter, and I have half given up on cleaning it.
However, I didn't want to leave it like this, so I was looking for something better and found this.
I purchased this product expecting it to work as well as it looked, but it was even better than it looked!
The size is a little large and the core wire is hard, but that is good!
A 1400cc straight-4 Engine is wide, and being wide means that it takes a certain amount of force to shove Brush into it and scrub it.
LargeSize and hard core were exactly Exactly for my use.
Also, the core Wire is not very thick, so it will properly fit into the gap.
After washing the car using DAYTONA's Shampoo in combination with this, Engine has regained the beauty of its original black paint!
This is highly recommended for those who want to keep Naked motorcycle's Engine appearance beautiful!
View detail
I love it.
The Large is very good and I use it for Oil change trips.
There is no problem in particular, but if I may be so bold, it would be helpful if the paper could be folded easily.
View detail
Used for Overhaul
Used on NSF100 front forkOH.
Essential Items for oil level adjustment.
The hose and syringe are sometimes easy to disconnect.
View detail
Purchased for personal use
[How is it used?
Purchased as an on-board tool for my motorcycle
Was the one you received as per Image?
KTC, so the texture is good and just like the Image.
How was your experience with it?
It fits with Snap and has good dimensional accuracy and can be used with confidence.
It is inexpensive, so it's great for personal use.
View detail
Replaced with a reliable manufacturer's product for future Motorcycle tinkering.
[How is it used?
I used to use a tool sold at Home center, but I was licking the Nut and so on.
We purchased this product as a reliable manufacturer's product.
Was the one you received as per Image?
Matte texture, Laser marking and was as per Image.
How was your experience with it?
The dimensional accuracy is also no problem at all, and it is good to fit Snap to Nut.
Matte texture also fits well in the hand.
How did it compare to other products?
It is a world of difference from the inexpensive tools sold at Home center. A little more.
I regret not buying it earlier.
Requests, etc. to Manufacturer
When the tool box is stored upright, it is unstable because of the protruding hinges,
I would like to see a structure that does not stick out.
View detail