Reviews
Soak before fitting
I soaked them in warm water prior to fitting, as per the advice of other reviewers.. No issues getting them on the levers, it did take a few minutes for each side though. They are sufficiently firmly in place that they don't move around at all. Although I expect they may shift a bit if they get wet. View detail
Difficulty in inserting into Lever is a drawback!
It feels good and will last about a year! The only …Minus is that it's hard to insert into the lever!
I can't get it in properly unless I put it in boiling water to warm it up… it rips if I force it in lol.
View detail
SP Mukawa Lever grip
[How is it used?
Used for scooter levers
Was the one you received as per Image?
As per Image
How was your experience with it?
Good feeling when gripping.
[Points to note]
May not fit depending on Lever size
How did it compare to other products?
There is no comparable product.
View detail
Comfortable when riding bare-handed
I ride bare-handed in the summer, and it feels much better on my fingers when I have it. I don't feel like riding without it.
When installing, it will not go in if it is only wetted with water, so it is easier to install if a mild detergent is applied to the lever side.
The clutch side tears early, but this is also the case with other companies' products.
View detail
Expect durability!
I used to use Poshu's Sponge type, but it broke after about a year.
I know this type of product is consumable, but I liked it because of its non-slip and thermal protectionMaterial:I bought this one from Rubber.
It's cheap, but the above two points are effective, and the only thing left is durability.
View detail
Is good
It is very good for non-slip effect when used on the Lever.
The thicker lever makes it easier to grip and maneuver.
The coloring gives it a custom feel.
View detail
Good price
I have installed the Lever Cover on most of the motorcycles in my garage, and when I first installed it, it felt strange because the lever was a bit thicker, but the fit was good and it looked fashionable, so once I used it, I got used to it. I am very happy with the results.
To install, it is difficult to insert the cover into the lever, but if you put a little detergent on the lever, soak the lever cover in water, and slowly and unhurriedly turn the cover round and round, it will go in. Once it is in, make sure to rinse off the detergent and dry thoroughly. Never use lubricant because it will not fit.
View detail
I think it would be good for a small Accent.
I had a hard time installing it at first, but after soaking it in hot water for a while, it was super easy to install.
It looks good and seems to be easier to operate.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA Cross Cub 50, HONDA cross-cub 110
One point on the brake lever
Installed as a dress-up for the CROSS CUB Brake lever. It is expected to relieve the coldness of the lever in winter.
I was able to fit it without ripping it by wetting it with water thoroughly when I put it on.
View detail
Effective
I use thin Gloves as I use the Handlebar Cover and Grip heater in winter on my PCX125 for commuting and I use thin Gloves.
Then the Brake lever is cold, so I installed this Sponge.
The effect is Large, but I take it off in the early spring because it will be cut off from the edge.
I wish it was a little more durable and 2Season usable or cheaper.
View detail
Be careful not to pull too much.
It is easy to install but you need to be careful not to pull too much to avoid tearing. View detail
It is effective in preventing slipping.
I used it for LEAD110 and Lever, but I think that it is very effective in preventing slipping. It is easy to put on and take off and the custom look goes up. View detail
I think it's good for Parenthesis.
Installation is also very easy, just plug it in.
There is a bit of an Impact around the Grip and it looks good.
I will only use one because it's a LITTLE CUB, but I'll keep the other one in reserve.
View detail
I ruined one of them, but I still want to put it on without giving up.
This is a universal product, so it's not always the same, but it's a good idea to pass it through the diameter of the lebar end. The hole was too small to fit it well. The Clutch Side was installed with better slippage, but the Brake Side was installed while I avoided it.
I couldn't give up, so I bought another one and put it on. When I borrowed a compressor and installed it while wiping the air, it was possible to install it without difficulty. Because there is no Air compressor in the home, I will think about it. However, when the hole is made Large, it is said that it is one advantage and one dislocation after the installation. I think.
Personally, I can't feel the coldness of Lever in the winter and BrakeTouch is anti Linear (lol) is literally a good Cushion for me, as I'm not a good driver. It has become. Even though it's an inexpensive product, I lowered my rating a bit because it was difficult to install, but I'm sure it will continue to be ruined and I think I'm going to buy more and repeat the process.
View detail
Once received the goods.
Once received the goods. Good quality products are very easy to install. Affordable and fast Easy to use. One color in use and very good packaging. One set of 2 pieces, both left and right, but the logo removed very easy and sticky. View detail
Once received the goods.
Once received the goods. Good quality products are very easy to install. Affordable and fast Easy to use. One color in use and very good packaging. One set of 2 pieces, both left and right, but the logo removed very easy and sticky. View detail
Grip
This is the second time buying this grip. Good feel on the lever. Nice material and the feel on the grip on brake or clutch improve. More response on brake tap on fingers. View detail
Good for vibration countermeasures
Grip is also made soft material, vibration is not transmitted to hands and it does not get numb and it is saved.
Also in the summer winter, there is not much heat from Lever.
The interval between Grip and Lever is slightly short, so my fingers will hit you, but I think this is unavoidable.
I think that the price is somewhat higher, so I think that it is better to buy it at the time of Sale etc..
View detail
Fits: HONDA Forza Si, HONDA PCX125, HONDA PCX150, HONDA CBR250R (2011-), HONDA CBR125R, HONDA CB250F, HONDA glom, HONDA PCX125, HONDA PCX125, HONDA DIO110, KAWASAKI NINJA250R, HONDA CROSSCUB , HONDA Forza300
It is a good feeling ♪
3KJ - Attached to JOG ♪
It looks good as it becomes Race ish ♪
It was easy to wear a little bit of water wearing and slightly squeezing ♪
View detail
Fits: HONDA Forza Si, HONDA PCX125, HONDA PCX150, HONDA CBR250R (2011-), HONDA CBR125R, HONDA CB250F, HONDA glom, HONDA PCX125, HONDA PCX125, HONDA DIO110, KAWASAKI NINJA250R, HONDA CROSSCUB , HONDA Forza300
I like the feeling of use.
It will be the second purchase. I purchased it with double-sided tape because it failed to install on the clutch side at the time of the first purchase, but I used it by sticking with double-sided tape, but I decided to re-purchase because I lost it while driving. Although it was described in the manual to insert the product using only water, it was difficult to wear it with this, and because there was a great possibility that it will be cut again, it is easy to slip on the product and the lever end part I tried installing it by blowing a little silicone spray so as to make it easy to install. However, after installation, if you do not degrease with a parts cleaner or the like, it will rotate with Zuzzle every time you hold the lever. View detail