Reviews
Cowl drilling required
I ride a CBR600RR (2009).
I purchased this product because I was told it was compatible, but I could not install it without drilling out the cowl.
Fortunately, I did not have to drill holes by diverting the Slider Bracket that I had originally used, but of course I had to choose and purchase the Bolt myself since I could not use Included Parts:.
If you purchase the product, you should be prepared to drill holes in the Cowl.
View detail
Fits: YAMAHA XSR 700, YAMAHA MT-07, YAMAHA XSR 700
Communication between Webig and the manufacturer is slow because the product is made overseas.
I ordered in February and received it in March.
As mentioned in other reviews, the Quantity:Pair (for Left and Right) However, there was a spatter in the Pipe and a large rattling sound was heard, so I had the One Side returned and replaced.
The replacement product arrived in late April and I finally tried to install it during the GW holidays, but the holes were not aligned …. Unfortunately, it was not the level that can be adjusted by drilling a long hole.
As of May 14, I am in the process of requesting a return & return Gold.
I realize that it has already been about three months.
It is a pity that I cannot install it because I like the shape of the product.
It had been a long time since I had seen such a ha-gap foreign product.
However, I think Mr. WeBig's response is good.
View detail
Rear Axle SliderShaft is too short to install.
You should not buy it. It will be a waste of Gold. View detail
Fits: YAMAHA R1, YAMAHA R6
Not fit for yzfr6 08
It says "r6 06-13" but it didn't fit at all. Why is that? View detail
Hmm
Scheduled to arrive in May, but arrived in March ahead of schedule.
When it came time to start the GW installation.
Some Screw sizes are slightly too Large.
The Female Screw on the Engine side has been shaved and started.
Abandoned installation in the middle of the project.
View detail
I will not buy it again
The Bolt that came with it was shoddy and broke during installation.
not worth talking about at all
View detail
Lowest
The length of the bolt in the Included Parts:section is not correct and cannot be installed as it is. This may be the case with parts made overseas and installed on a foreign car, but we are honestly disappointed with the condition of the parts despite the long time it took to receive them. View detail
The dimensions don't match at all.
I bought this for the rear, but the shaft is not long enough to fit the guard. I'm not sure. View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3
impossible to install
I waited for the delivery date and was disappointed with the product Rear and Quantity:It was a set purchase, but the front as well as the rear are non-conforming.
I also checked the fit, but Shaft is too short to reach.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3
impossible to install
I waited for the delivery date and was disappointed with the product I also checked the fit but shaft is too short to reach View detail
KIT parts cannot be fixed alone.
It was a ridiculously defective product for a not-so-cheap price of $6458.
KIT parts alone cannot be fixed because the fixing bolt (M8) does not match the hole diameter (M10) of Shaft parts.
(There are too many gaps and rattling).
I thought about returning it, but that would be a pain in the ass, so I'll just add my own parts to it. 。
I bought an Aluminum Pipe (10mm OD, 8mm ID) at Home center and made a Spacer to fill the gap.
Added Washer so that Bolt's Torque can be applied without difficulty. 。
It's a shame, because it would have been a great product if I could have added the parts and installed it properly myself.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3
Does not fit.
The boss diameter and Shaft length were totally different. It is an expensive study. It is useless. View detail
Fit?
I was going to install it on a 2005 CBR1000RR SC57, but
Shaft length is too short to fit.
The Screw mountain of Shaft must be applied to Tap.
I bought it because I like the design and I will find a shaft at home center that fits the length and install it.
View detail
Current MT09 cannot be mounted on the short bracket
The current MT09 has a short bracket and cannot be installed. I think it is defective It's a shame, because it's only about a year old, so I guess I'll just have to give it up View detail
not fit 2019 sv 650
The rod that came with is too long...i have to cut it short myself to fit...a lot of work and waste of time...not recommended unless they fix this. View detail
I've been looking forward to this?
Sorry
Before I knew it, it was Cancellation
You may have received an email
We'll just have to wait for Cancellation
View detail
The axis size is not fit for rear wheel
I ordered the protectors for rear wheel, when i want to install, i found that the rear wheel protectors axis is not fit for rear wheel (MT-10), the axis is only fit for front wheel. View detail
Can not be installed at all - - - -
Perhaps a completely separate model was sent - - - Front was patchy, but here Bolt's Length is too long and Slider Body both do not match the shape of AxleBolt at all. In the first place, only Package has a Vinyl bag, and ProductNo is not mentioned, otherwise for Front has no manual entry. Since the Front could be installed without difficulty, I tried to open it and try to install it, but it was useless. Since I opened it all out, it will be impossible for me to return it, I will fall asleep. From next time I would like to have product management solid. The image was for Front and Garbage that could be attached for Rear w View detail
It was a failure.
Since you can not open the Oil level gauge when you install it,
Oil There is a necessity to remove for every replacement.
Personally I could not use it at all.
Will not it be okay to buy those who do not have the problem in the above.
View detail