Reviews
![Rear Axis Slider Guards [Rear Axis Protectors]](https://img.webike-cdn.net/catalogue/images/41365/PKN_pict_1417609301960759_web_TS.jpg)
Unlike Front, Quantity:Pair (for Left and Right) There
I put on Rear Axle Protector, although there are pros and cons.
The image is after installation, but it is not very noticeable and looks good.
The damage may increase due to the longer sliding distance, or it may get stuck and increase the damage due to the lever principle, but we assume that the speed is not too high.
It is a 13mm Nut, but normal Glasses cannot be tightened because the Nut goes inside.
Also, when you close the Quantity:Pair (for Left and Right) If you don't tighten it evenly etc., one Bolt will pop out.
Unlike Front, Quantity:Pair (for Left and Right) There is a
I haven't experienced the effects. No effect." The company is committed to
I hope you don't feel it.
View detail
The Frame is subtle, long, and poorly made.
The length of the Frame is too appropriate. The actual product is quite small. View detail
I wasn't on the rear.
The front was attached by another manufacturer, but the rear was not attached, and I installed it so that the Swing Arm would not die when I fell.
The installation itself is simple with the ScrewShaft and Nut tightened from both sides.
If I wanted to, it would be easier to thread the hollow shaft and bolt it in place.
I also added it and the Maintenance Stand is now harder to use:。。。。
View detail
A bit of a disappointing product…
Slider's bracket has screws on both sides, so it's hard to screw it in evenly. Also, there was only one Cover for Nut in the box. Because I avoided the hot season, I gave up and installed it as it was because two months had passed since I bought it. It was cheap but a little disappointing… (>_<) View detail
The Screw doesn't fit.
I think things are good, but the Pitch on the Screw didn't fit, so I bought a Screw and put it on. View detail
![Rear Axis Slider Guards [Rear Axis Protectors]](https://global.webike-cdn.net/photo/impression/b2/b2f6ae69ec09bb124699139726a3aff7L.jpg)
It didn't come with a Nut Cap.
I have no complaints about the product itself.
However, I'm not convinced that one of Nut's PlasticCap shown in the product image was included.
Also in the Handling Instruction Manual. "using nut and cover it with plastctic cap I'm writing to say, … what do you mean?
The front one was attached, so it was even more mysterious.
I'm going to ask if you can send me just the Cap, but I'm not sure.
View detail
![RearShaft protector[Rear axis protectors]](https://img.webike-cdn.net/catalogue/images/41365/PK2_pict_000_web_TS.jpg)
Fits: YAMAHA FZS 1000 Fazer 01-05
It appears to be a very old stock item
I don't know if the Motorcycle is old, but it seems to be a very old stock item
I bought Gold, but it's not glossy at all, and it's clearly not Gold
It's very disappointing I should have used something like Black with no color influence
And the worst part is that the Nut hole is unusually small, and the 13mm Socket The wrench does not come in
I've fixed it with radio pliers and turned the Body, but it's not completely tight Anxiety
I had to grind the 13mm Socket with Grinder to make it tighter But no matter how thin it was, it just wouldn't fit Give me back my Gold!
I regret that I could have used a domestic Universal Product
View detail
I couldn't install it because the Shaft was not long enough
The general comment is correct, the Shaft is not long enough and comes out of the insertion slot on the other side of the closing I'd like to.. It was not long enough to fit As you can see in the photo, it's only this length that comes out, so it's just a matter of fixing the Bolt The Screw length is insufficient; check with HondaDREAM I ended up returning this product and replacing it with a similar product from Ditna View detail