Reviews
The Z900rs requires some modification.
First of all, the design of the text is different between the image and the real thing, but I didn't mind it too much.
The Left Side Lock nut is not included in the kit, so you need to prepare it by yourself. I first selected "Pitch normal" for the Left Side Lock nut and failed to use it. (You are solely responsible for your own mistake.)
The lock nut of the M18 was too tight for the Left Side Protector, so I had to grind the inside of the Protector a little to fit.
Quantity:Pair (for Left and Right) The bolt for penetrating the "B" is also a little long, and it is difficult to apply the tip cap, so both ends were shaved off.
Note that the z900rs does not have a bolt on and requires some modification.
View detail
Incompatible with ’23RnineT
First, it does not fit the ’23 RnineT. The Axle seems to be shaped differently and the One Side boss does not fit inside the Bolt of the Axle.
So I cut off the boss and managed to use it.
Disappointing result for the time it took to deliver.
View detail
Hopefully there won't be a time when it will be useful.
It is easy to install, but I wonder if it is because the Engine is a hanging type.
Quantity:Pair (for Left and Right) The Bolt to be installed after either 0Comma or 0.5Comma. About the same as
It was hard to get in, but after a couple of hang-hangs (without force) with the plastic pan, I was able to get in.
I got in easily, although it might be right to make it stand upright and jack-up?
View detail
It's discreet and nice.
I put on the front axle protector, although there are pros and cons.
The image is after installation, but it is not very noticeable and looks good.
The damage may increase due to the longer sliding distance, or it may get stuck and increase the damage due to the lever principle, but we assume that the speed is not too high.
It is a 13mm Nut, but normal Glasses cannot be tightened because the Nut goes inside.
Also, when you close the Quantity:Pair (for Left and Right) If you don't tighten it evenly etc., one Bolt will pop out.
I haven't experienced the effects. No effect." The company is committed to
I hope you don't feel it.
View detail
Axle Slider
Easier to install than Front. It does not look good. View detail
Fits: YAMAHA MT-07
Is it such a thing?
The large size of the Guard on the Right Side of the vehicle does not match the diameter of the Outer tube at the insertion point.
It's a lousy design mistake.
As you tighten the Nut, it will become slanted.
I thought about shaving it off and fixing it, but it got too cumbersome in the middle of doing it, so I just installed it at an angle.
Probably won't bother anyone but the Owner, though.
I may scrape it off and reattach it in the future if it bothers me.
View detail
Product is good, but there is a problem with installation
The instruction manual for the installation was in a foreign language (English version?) and I couldn't understand it at all, even though I used a translation application.
Also, the pictures in the Instruction Manual were not helpful at all because they were of a different car model even though I specified the car model.
The bolts that came with the car were not very good quality and I had to buy them myself to install the car.
View detail
Installation gives you peace of mind.
It took a bit of time to get it to me because it was ordered from abroad, but it arrived safely. It was very well packed, but the quality was excellent:Pair (for Left and Right) Both of them were scratched and the paint was peeling off. I had a bad feeling about this, but as I expected, the dimensions were not accurate enough to easily install it. I have to widen the bolt holes to fit the bolts and the quantity:Pair (for Left and Right) It is a long Bolt that is connecting the Original is a normal Bolt, but the one that comes with it is a long Bolt. This is a double-sided nut with a screw on both ends. In addition, because this nut has a resin in it to prevent loosening, even if you turn it from Both Sides, you can only turn one side. It screws in and out. When I tried to change to a normal nut, the Pitch does not fit instead of the MScrew. Also Quantity:Pair (for Left and Right) The center of the welding nut of the joint part of the joint part of the Bolt cannot be screwed in because the center of the welding nut is out of alignment. It was such a difficult work, but I think that the person who can do some processing can install it. It looks very compact and sturdy. It seems to protect the engine in the unlikely event of a fall. View detail
ProductBody is zero, Included Parts:Bolts? No
ProductBody is 0 good, Included Parts:Bolts are ? No M10×60mm 1.25Pitch 2pcs M10×70mm 1 .25Pitch1 pc
M10× 75mm 1.25 Pitch 1 pc (Bolt to mount on vehicle) All 4 pcs Inaccurate, cannot be screwed in, Material:I bought the Stainless Steel at the nearby Screw shop By the way, it cost me 2013 yen for 4 pieces
View detail
Fits: YAMAHA XSR 700, YAMAHA MT-07, YAMAHA XSR 700
Accuracy X
Right does not fit at all:I hung up a little 2pcBolt and forced it on with the force of the screw
I don't know if it's gonna bite off the Bolt
It's XSR700 compatible, but I don't think it's something you can call compliant
It's cheap and good looking, but..
View detail
Fits: YAMAHA XSR 700, YAMAHA MT-07, YAMAHA XSR 700
The quality is too bad
Installation is easy with a bolt on and a torque wrench 。 It seems to work reasonably well
However, the quality is too bad! The paint is flaky when you press your finger on it, but there are pieces of steel in the PipeGuard Caracalla And sound 。 I can even hear it while driving 。 At first I thought it was a noise from the motorcycle itself, so I had to check it several times while riding was 。 I have been using various products from overseas parts manufacturers, but they are not as good as the domestic ones I've never seen such a bad product, even though it's not the standard
I installed it because I couldn't make it on time for touring, but if it's as cheap as the above, it's good If you are a person who is not a fan of the
They also accept returns, so if you're not in a hurry, give it a try
View detail
Is that about right?
I've seen other people's imprints and it looks good
I bought it The price is so cheap
I installed it as soon as it arrived
Quantity:Pair (for Left and Right) The hole in the Bolt that attaches to the bar does not fit
Get this Site to replace it as soon as possible
I did, but the Manufacturer responded with
This Bolt doesn't need to be worn to be strong
No problem, he said
Then why did you start using the Bolt to fasten up?
Are you there?
Is this how it's done?
It was a cheap purchase
View detail
65 points
I bought it as a SliderGuard, do you like the Design? I couldn't say for sure until I came, but the color BESE Black Plate BLUE It was quite beautiful and I liked it The reply said two months for delivery, but I was surprised that it came within a month, installation was easy! However, it took time to remove the FrameBolt of NORMAL because it was hard I removed the FrameBolt and put in new parts It's a little difficult to position the Plate It is the end It's an easy task if you 。 I don't want to be a part of this, but I'm happy with the design, the colors, and the way it looks View detail
Cospa is expensive, but I'm not so sure about the price
With the attached Bolt, it is a little short and cannot be installed I thought about returning it, but I bought a little long Bolt at the nearby home center and installed it is just one more thing, two longer, and the installation is Smooth, but I wonder why View detail
I'm not happy with the installation
To go ahead with the results, it seems to have come off while driving and was lost
The pedestal and the Slider are separated However, the engine mounting bolts hit the engine mounting bolts before the seat surface and cannot be completely tightened Mm
I think this is because of the design of this product, but I think the design is wrong
If you use it, don't forget to apply Screw Lock and check for looseness on a regular basis
View detail
If you're looking for a good costumer, this is it
I don't know how effective it is because I haven't fallen over yet, but it seems to protect me well because of the large size It is
I don't mind, but it also comes with a Bolt cap, so if you can see the head of the Bolt, it looks tacky You might be happy with the way you feel
Best of all, it's cheap
View detail
Fits: DUCATI MONSTER1100, DUCATI MONSTER696, DUCATI MONSTER796
I think that it is a very good product if it judges by the price.
Please note that in the conformance chart described in the Catalog, MONSTER S2796 is not fitted together with Shaft length both before and after.. Since Front interferes with Axle, Shaft length is not enough in reverse. View detail
Compared to competitors' products, COSPA is reasonable
BMW I mounted it in S1000R 2017
Mounting is easy because I only tighten Shaft from Both Sides with Nut
Shut is not stopped because Shaft is short though Nut with a rotation angle stop is attached
I am sorry it is exactly as long as 5 mm longer
Nut 's Cap is included as well as COSPA is good just to improve it
View detail
Fits: MV AGUSTA BRUTALE675 , MV AGUSTA BRUTALE800 , MV AGUSTA BRUTALE800 DRAGSTER RR, MV AGUSTA RIVALE800
Before using Rust - - -
By saying Large type Motorcycle for the first time, I felt Risk of standing gift, so purchase.
Protector that conforms to Brutale 800 is few, and only this product or OEMOption only compatible goods could not be found.
OEM Product is so expensive that it is appreciated to be able to buy Protector at this price.
Since all necessary items for installation are complete, it seemed possible to install if only a tool was prepared.
However, it is worrisome that Screw is pretty much rusting even before use. Is it such an overseas product?
View detail
It looks good.
MT-09 (2017) Mounting on.
Because it interferes with the Cover next to the Radiator, it can not be installed as it is.
I made Color and built it somehow.
By all means this shape is good, I think that you can purchase those who have confidence to process and install them somewhat.
View detail