Reviews
BIGSize！！
I use it to fix sub-computers, voltmeters, oil temperature meters, thermometers… and other electronic devices that I have installed in my car. It is easy to attach and detach, yet it is very strong! View detail
For Mount bar mounting
[How is it used?
For rare vehicles that do not have a dedicated AttachmentMount bar,
Used to tighten the Bracket together with the Switch Box.
Was the one you received as per Image?
I have purchased this product in the past when it was processed on another vehicle,
The quality of the product is very low, and I think it's a perfect Spacer product.
Was the installation difficult?
Both inner and outer diameters are exactly the same as indicated, so it is a simple installation.
How was your experience with it?
The outer diameter is exactly the same size as the head of a Bolt with a hexagonal hole,
It fits in the bolt hole of the SW-BOX EXACTLY as we intended to use it.
[Included Parts:were they on?
Included Parts:No setting
[Was there anything that disappointed you?
There is none
Other items that would be helpful
Since the only colors available are Silver and Black,
It would be nice to have other colors.
View detail
It cannot be used for Shinobi Sen Cowl (crying).
It's my fault for not checking carefully, but I bought the upper 6 push rivetsfor replacement of the front under cowl on my 2014NINJA1000, but the inside rivet size was thicker than the OEM Product and did not fit in the holes&hellip I bought this rivet for replacement for the upper 6 push rivetsfor the front under cowl of my 2014 NINJA1000.
For your information, the correct OEM Product number is 92039-0068. to
View detail
As expected of a ready-made product
I thought I could make it myself, but this time I bought it. It was a bit expensive. I'm glad I bought it because it turned out just like the image. View detail
Length and Working Space
We needed to change the Bolt that holds the Exhaust System in place, so we went with this one.
I would have been happy with one, but it's not perishable, so I'll keep it in the Screw box in case I use it someday.
View detail
alignment
I tried to install NPRO Ject's Twin muffler on my WR250X, but the Clutch Side interfered with the ZeroGee Tail cowl, so I chose this one to keep it off the outside.
It is better mentally than piling on the appropriate Washer or Bolt.
View detail
![[K-CON Pro] License Plate Base](https://img.webike-cdn.net/catalogue/images/69385/0901-657-00050b0_TS.jpg)
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
No loose ends!
I was looking for a M8, Stainless Steel, low profile nut with a non-loosening nut. I looked in Home center, but they don't have a Pitch 1.25. I looked in Home center, but they don't have a 1.25 pitch. 1.25 is non-negotiable because it is for a CUB that has a lot of vibration. I searched for a lot of options and bought 3 kinds of lock nuts from ConvenienceParts by KITACO.
Loosening stop is Friction ringType. The long formal name is new to me; I used to call it a UNut or a feathered nut. The feathers are used to apply torque to the bolt. When used on a long bolt, the load is too much and the feather is bent completely. Then the Torque will not be applied. As a result, the loosening stop does not work. It is not advisable to reuse a nut with bent wings.
I checked the size, pitch, and construction of the wings, and they are all fine. I have used 3 types of normal featherless parts with different parts, and even with 3 types, if they are feathered rather than featherless, the tightness is fine. I added a SpringWasher just in case. The height increased by that amount.
The instruction manual explains the length of the protrusion from the nut. This time, the protrusion is one notch, or less than 1mm, and it says that it can be used for other parts as well, since it says that it is large sturdy up to 5mm. Personally, I don't use winged nut for bolt that needs to be tightened and loosened many times. I don't often put on and off Torque rods, so I prefer to use them for my own purposes. [Color] Clear.
It has traveled more than 1000 km after installation. I did not use screw lock agent because it is stainless steel. I don't need screw lock agent this time.
View detail
Just in case.
It may not be an option, but Neck is the pricey one for this kind of thing. View detail
KITACOConvenienceParts has been helpful.
What made you decide to buy?
Because the ZitaRacing ScreenBolt does not come with a Nylon washer!
[How is it used?
To install the Zita Racing ScreenBolt!
[How was the installation?
It is Exactly to the size of ZitaRacing ScreenBolt.
[How was it when you used it?
Rather than installing the bolt directly, just inserting a nylon washer between the bolt and the washer will help prevent scratches. I think that even if you just have it as a spare part, you can use it later on! This is a product that is not likely to be found at a nearby home center.
View detail
For carbon silencer.
To Maverick's MV83Carbon silencer.
The Maverick Exhaust Band is a common silver color, so I thought it would be more consistent if I changed it to black. I changed it to black to make it look more consistent.
The color and Size matched.
The Bolt hole in the band section is narrow between the Bolt hole and the Exhaust System, so it might be a little bit higher.
The bolt nut that came with the product was too small to use, so the OEM product was reused.
View detail
I made a mistake in the size and couldn't use it, but I'm making it Stock.
[How is it used?
Generator fixed bolt from Nabe Screw during EngineO/H of YAMAHA/TZr50R.
I bought this one with the intention of replacing it.
The result was not usable because of the wrong Size, but we are using it as a Stock for something else.
How was your experience with it?
I think the quality is good enough.
How did it compare to other products?
I don't have anything to compare it to, but I wonder if the price is higher than Home centeretc.
There are many types of this kind of products, so it is easier to find them on Net.
[Points to note]
nothing special
View detail
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
Many color variations available
A wide variety of color variations are available, making it easy to match the color of the car body.
The price was inexpensive and helpful.
The texture is perfect.
View detail
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
Step up from SteelScrew!
[How is it used?
Screw was replaced with external Fender, so Screw was changed from Steel to Material:Replaced with Stainless Steel.
Was the one you received as per Image?
Quality is as good as the Image.
Was the installation difficult?
Installation is easy as the SteelScrew is simply replaced.
How was your experience with it?
Fender is often exposed to moisture, so the replacement was made in consideration of durability, but it can be used without worrying about rust, so it is a sense of security.
[Included Parts:were they on?
No other than Screw.
[Was there anything that disappointed you?
The NORMAL Screw is slightly rounded, but this is a dish Screw, so the shape is slightly different.
▼I'm afraid of biting, but I think it is better than Steel rusting.
View detail
I don't know if it will fit, but I bought it anyway.
I don't know if it will fit, but I bought it anyway. View detail
Convenient to make it the same color as OEMHarness.
It is convenient to unify the Minus power supply system and Earth system of the retrofit attachments with the Earth system of Kawasaki OEM Harness, Black/Yellow. View detail