Reviews
For Wiring Protection
I chose Colgate Tube for the first time because I didn't know what to expect and I chose the 7mm inner diameter.
I did not have an insertion jig, so I had a hard time threading the wire using the slit. I threaded the Bullet Type Terminal first, and then slid the flat Bullet Terminal along the slit to thread the wire, but this time it was about 50 cm, so I managed to thread the wire.
This is the first time I have used Colgate Tube I.D. which is good and helpful.
View detail
Ideal for preventing damage to Number….
I noticed that the reverse side of the License Plate was getting dirty with mud and Asphalt-like substances, so I purchased this plate for two purposes:to prevent dirt from staining the plate, and to prevent damage to the License Plate since it was almost bent when the Number was caught a few times.
After installation, it is completely hidden by the License Plate, so it is not visible from the rear, but the reverse side is protected and serves as a reinforcement for the License Plate, which may be useful for Large to prevent damage.
In my case, I bought it together with ”Nasa Type Number Plate Holder Set” and did a dress-up at the same time, albeit very slightly.
The aforementioned objectives of the purchase have been fulfilled, and the rubber cap to suppress plate vibration is also a nice touch.
In my opinion, Plate seems solid, thick, and sturdy. I searched on the Net and found one with a weight of 210g in the product description. If you don't mind the slight weight of the car, I don't think it will affect your posture, but I was a little concerned about the weight of the Plate.
View detail
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
Step up from SteelScrew!
[How is it used?
Screw was replaced with external Fender, so Screw was changed from Steel to Material:Replaced with Stainless Steel.
Was the one you received as per Image?
Quality is as good as the Image.
Was the installation difficult?
Installation is easy as the SteelScrew is simply replaced.
How was your experience with it?
Fender is often exposed to moisture, so the replacement was made in consideration of durability, but it can be used without worrying about rust, so it is a sense of security.
[Included Parts:were they on?
No other than Screw.
[Was there anything that disappointed you?
The NORMAL Screw is slightly rounded, but this is a dish Screw, so the shape is slightly different.
▼I'm afraid of biting, but I think it is better than Steel rusting.
View detail
Convenient to make it the same color as OEMHarness.
It is convenient to unify the Minus power supply system and Earth system of the retrofit attachments with the Earth system of Kawasaki OEM Harness, Black/Yellow. View detail
Convenient to match the Wiring color of OEMHarness.
It would be helpful to be able to make the color of WhiteHarness, which is equivalent to the Batch+ after the KawasakiOEMHarness junction box, and the Batch+ of the retrofit Attachment, the same White. View detail
It is usable enough. Soft but not tight enough to lick.
It is often written that the six corners become rounded, but when I tightened them with the torque wrench by pressing the tool firmly, the corners were indeed slightly deformed, but not to the extent that they became impossible to tighten.
If you say you can't install it, it's probably because of poor workmanship.
If you discount it as a cheap product, it's not bad at all.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Convenient
It is useful when you are not comfortable with drilling a hole to fasten a bolt or directly affixing with double-sided tape.
Examples of use include Income's Fix and Paste Type's Add Meter.
Especially when additional Meteretc. are attached with this, it is quite easy to attach and detach when something happens to Wiring-related.
View detail
It's kind of expensive.
I used to buy Vinyl tape for around 100 yen and used it for wiring, but after a few years the surface became sticky and I didn't like it, so I bought Harness tape, which is a little more expensive, and rewound it. I am looking forward to the future. View detail
To stop Rust.
XSR900 has bolt holes for carriers? I didn't want the bolt holes to rust, so I put them on.
Gold in casual places is nice.
View detail
A friend of old cars?
I'm not sure about current vehicles, but this is a common two-turn Bullet Type Terminal on older vehicles.
I get the impression that there are a lot of them, especially around Tail.
View detail
For additional Wiring
I found an article that the Bullet Type Terminal for Motorcycle is slightly different in size, and it seems that it is not Exactly fitted to A0 products, so I bought one to try it out.
I do think it's harder to pull off than A0.
Why would they change the Size?
And I didn't know there was a difference even among MotorcycleManufacturers.
It's an essential component for safe Wiring processing.
View detail
for adjustment
Repurchased to add a step on the Screen I had previously put on. View detail
Easy to use
I bought it because I couldn't find it at my favorite store and there was just a Point.
It is easy to use, but the rubber rubber doesn't last long because it is used in a place where it is bent many times.
We purchased several in stock as consumables.
View detail
Quantity:It would have been better if it was 1 Set of 4pcs,
I purchased the 4mmSize Rivet because I needed it when installing the MC21 Screen.
What I wanted was 4 pieces, but the Quantity:I bought two because it was 1 Set of 3pcs.
There are two different lengths of 4mm Nylon rivets from KITACOConvenienceParts, and I was not sure which one was better. There are two types of rivets with different lengths, and I was not sure which one was better, If it's a scuzzy one, why not just put a Washer on it?" I bought this one because I thought it was perfect.
OEM Parts are still available, so if you are concerned, OEM Parts are the way to go.
I am satisfied with the price, which was less than the cost of four OEM parts.
View detail
It can be used normally
The female side of the Harness was too stiff, so I used this product to change it. If you tighten it too hard, the cable will break and the connector will become useless, as is the case with other connectors. View detail
To MONKEY125.
For rain protection after connecting electrical components to MONKEY125. View detail
Ideal for blowby gas extraction
The basic application is as shown in the Title. However, it is too thin to be used for cars and motorcycles with high engine displacement volume, which may result in poor performance and malfunctions.
The durability of the paint is unknown, so it was rated 3 Stars.
View detail