Reviews
Inexpensive but very effective Large
The rattle of SR400's clutch lever has become very bad, and it shakes when idling. I left it alone, but then I found out about KITACO Spacer Washer and bought it.:1pc.0.3mm thin, Quantity at top and bottom:I put in 1 pc. at a time. The rattles are gone. But you have to have enough clearance to put two pieces in. In that case, you need to use Quantity:Only 1pc. is also available. There are 0.3 and 0.5mm thicknesses and several diameters. View detail
No complaints except CenterGap.
I used it on the Handlebar Clamp of my Bonsai Motorcycle. The part where the Hexagonal Wrench is inserted is gapped from the center, but there is no rattle at all, so it can be tightened firmly with Torque. I think it is a good cost performance to replace the rusted bolt as it gets rusty. View detail
ExactlySize
License Plate and ExactSize Plate
Unobtrusive, but that's what I like.
View detail
Can be inserted into a hole and fixed in place.
It is a product that can be inserted into the hole and fixed with Tie Wrap.
Thank goodness I usually don't sell Rose.
View detail
I bought this because I wanted to take the negative pressure out of the Manifold.
I drilled a hole in the manifold and cut a tap to attach the negative pressure pump. View detail
Thank God they don't sell them at the homestore.
When I installed NAMETALCraft's aluminum chain guard on Over Racing's Swing Arm, the bolt nut on the reverse side was dangerous because it interfered with the chain when I fixed it with the bolt on the front side bracket. I inserted a 12mm Truss Screw from the Reverse side and fixed it with this Cap Nut with Flange from the outside using an AngleDriver. After that, there was no more interference and I am satisfied with the result.
This was helpful because these special Nuts are not sold in Home center.
View detail
No motivation, no 4mm.
Bush replacement made it thicker by an ear, so Spacer took care of it.
5mm/4.8 3mm/2.8 each, short of dimension
Quantity because it is too much trouble to shave Spacer without 4mm Lineup.:Pair (for Left and Right) Washer adjustment in non-etc.
View detail
PetitCustom
PetitCustom Bolt Hole Cover for Handlebar Clamp. View detail
useful accessories
The K-CON anti-vibration rubber purchased by this webike is used to replace the aging and cracked rubber pad on my motorcycle. I found it on webike after searching for a long time. The specification and size are clearly described. The next thing is to hope for it Durable and won't crack quickly. -------------------------------------------------- -------- The K-CON anti-vibrating rubber purchased by this webike is used to replace the rubber pad that has been aging and cracking on my motorcycle. I found it for a long time to find it on Webike. The specifications are clearly described. Durable will not crack quickly. Powered by Google Translator View detail
For carbon silencer
I had heard that it was difficult to find the right size, but I can fix it to Maverick's Silencer without any problem.
Recommended for those who want to Blackout.
View detail
Replacement Oil Drain Bolt Sealing Washer for the Grom
About quality and texture: I am happy with the quality of the sealing washer from K-CON, the washer is made from aluminium and has an outer diameter of 20mm, inner diameter of 12mm and a thichness of 1.5mm. About the feeling of use: The oil drain bolt was showing signs of oil leaking and after the replacement of the sealing washer and tightening it to the correct torque value there are now zero oil leaks. Products to buy together: Somemore sealing washer both from K-CON and Honda would also be desirable to purchase along with this sealing washers as these are consumable items that need replacing on occasion. Difficulty of installation: The process to install takes about 5 minutes, give the mating surface a clean, fit a sealing washer up the head of the oil drain bolt and tighten down to 24N . m. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting a quality part from K-CON that was in stock and ready to ship unlike the Honda sealing washer but the K-CON sealing washer is slightly more expensive. About shipping and packaging: Sea frieght was my preferred method of shipping due to the lower cost but currently this service is unavailable from Japan Post, EMS is much faster which is nice. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: These sealing washers are a consumable item and you need to have spares on hand when carrying out your own maintenance as they tend to leak after being re-used a few times. View detail
Size did not match ADV150
It was meant for Honda, but it was not available because it did not match the size of the push rivet used on the ADV150.
I think it is a normal product for a push rivet.
View detail
Used to install XJR1300Slip-on Silencer
[How is it used?
Used to install XJR1300Slip-on Silencer.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
Since it is an Oval shape Exhaust System, I had to shape it into an oval shape, but it was easily done by hand. Installation was also easy.
How was your experience with it?
It works fine, but I am concerned about the durability of the material since it is thin (1,2?).
[Included Parts:were they on?
It comes with.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
For installation of Grip heater (Crimp available)
Used to install Grip heater.
SUZUKI ADDRESS110, I used it to connect from Attachment power supply to Grip heater power supply.
The only work to be done is to install the Wiring and terminals of the Grip heater into the Coupler using a Crimp to ensure that Plus and Minus are not mistaken, and connect it to the Attachment power supply on the car body side.
I have been using Grip heater for about a month and have been able to use it without any problems.
View detail
emergency measure
Finally, the end-Quantity:The Thailand coil of GB250 CLUBMAN's clutch wire broke and I used it as a first aid kit. The wire was out of order at the point where it was cut, so I used an on-board tool to adjust the tip and cut the end-quantity.:I inserted it into the set and fastened it with the included Hexagonal Wrench. I was surprised that it worked better than I expected, and it is a good thing to have one with you when touring. I learned a lot this time because I can work faster if I have a nipper to adjust the wire. I will add a Nipper to my on-board tools. View detail
Cheaper than OEM
We purchased more because they are cheaper than OEM!
When they are old, they are hardened and I replace them when they are Rose.
This is a necessary component to prevent Cowl from cracking or over-tightening!
View detail
Recommended
Used when Oil cooler is installed!
I hate colored stuff and there is Black and I bought it!
Simple and Parenthesis good!
View detail
I use it to organize Wiring
Battery charging terminal for external charging and USB navigationetc.… Used to organize all kinds of wiring.
Unlike cheap vinyls, it is stress-free because it is not sticky!
This is Stress-free! I will definitely recommend this one!!!!
View detail
Shiningly glowing and looking great!
Gold color is beautiful!" and my neighbor's beautiful girl gal JK is very receptive lol!
Gold color seems to be accepted by gals… Riders who want to be accepted by gals, let's install it!
Recommendation!
View detail
Used for 250SL (Repair)
I bought a new Ninja 250SL… because I lost my push rivet at some point.
I purchased and used it. The quality is high and I can use it without any problem, but I still feel that it is rather expensive…
View detail