Reviews
I think it's good
It is just a decoration, if you like.
There is no sense of discomfort as if it had been attached from the beginning.
It is completely self-satisfying because no one but the person himself notices it.
View detail
Used with BURGMAN 200
Used with BURGMAN 200
I lost the clip nut that holds the lid of the battery case under the foot board, so I was a little anxious about the size, but I bought it.
There was a 0.5mm hole gap between the battery case and the case, but I was able to install the case without any problem.
View detail
To MONKEY125.
For rain protection after connecting electrical components to MONKEY125. View detail
desorption
I bought this to fix Screen to prevent scratches and for easy removal.
The price was reasonable, but the diameter and length were not quite right. The diameter and length did not fit well.
View detail
Ideal for blowby gas extraction
The basic application is as shown in the Title. However, it is too thin to be used for cars and motorcycles with high engine displacement volume, which may result in poor performance and malfunctions.
The durability of the paint is unknown, so it was rated 3 Stars.
View detail
Height adjustment
I bought a used rear caliper support and used it to adjust the height because the wall thickness was different, perhaps due to a difference in spec.
The Swing Arm was black, so I purchased this color, which was available in the same color lineup.
It is good to measure the height and diameter in advance so that you can choose from a wide lineup of similar Sizes.
It was firmly beveled and ready to use as soon as it arrived.
View detail
For fixing Silencer
Purchased for use in the Band section for fixing Silencer.
It seems to be good for vibration and scratch protection. The price is not that high, so I hope it has some Rubber durability.
The product is not that expensive, but the cut ends are slanted, and I had to cut them a little to use them. I would like to see the product sold with a straight cut.
View detail
V125 K5 Fork Bottom Bolt Gasket as
V125 K5 Fork Bottom Bolt Gasket as
Cheaper than buying OEM Product
View detail
be extremely thorough, focusing on even the finest of details
The mounting hole on the bracket side is an ellipse, so it can be done haphazardly.
In this case, it was used to install MONKEY's Rear Fender.
View detail
It would be helpful to have a fine Size selection.
The bracket of the Rear Sets was in the way of installing GCraft's CarbonPerafen, so we chose 20mm to shift it backward. View detail
For fixing plastic parts and
I thought, "Can't I use it to fix the Screen? The price was reasonable, so I bought it.
It was impossible due to the thickness of the fixed section and lack of length.
It can be used in other fixtures and will be used there.
View detail
I am satisfied with this price.
GCraft's CarbonPerafen is a surface [Color] I bought it to distribute the pressure with a thin Spacer with a Large tight outer diameter because it looked like it would crack with the Bolt that came with something like Clear.
The Spacer in this Series is finely Sized, which is helpful.
View detail
I used it to fill in the riddle.
The Camshaft ChainHousing of the Z900RS Cylinder block has a mystery hole that is not used on this Motorcycle.
The diameter of the hole is 11mm. I have been wondering about this for a while, so I use well nuts to fill in this mysterious hole.
I hope they will continue to do so because it is a product line that raises the level of custom culture.
I used a 9.5Φ C550 with a thin neck, and since the parts are just for decoration, I used an appropriate lightweight aluminum M5 bolt and cap.
Other than the mystery hole for the cylinder block, the Center Stand mounting hole on the Left Side can also be filled with this well nut and M5 bolt since the hole diameter is 11mm.
View detail
For vibration isolation
[How is it used?
I bought this to silence the explosively cheap inferior CenterCarrier installed on my CUB, which resonates at certain RPMs and makes a lot of noise. I installed it by inserting it between the vehicle and the body.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Just pinch it in.
How was your experience with it?
The sound has disappeared. It's the best.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Not particularly
View detail
To DJEBEL.
The rubber of the gasoline cap of DF200 DJEBEL was worn out, so we cut out this rubber in a circle and installed it. View detail
For Z125 Pro Dress-up
Kawasaki Z125 Pro I was looking for a mesh seat to decorate a hole in my dreary cowl,
I found this product and bought it.
(Work procedure)
Cowl removal.
Cut this mesh seat to a suitable large size using scissors and press it against the cowl from the inside. Cut the excess part.
It is not difficult to mold with AluminumMaterial, and it can be fitted to curved surfaces to some extent.
100s Epoxy Adhesive (The one that mixes liquid 1 and 2) fixed at
At first I was thinking of decorating only the Front part and the hole around the knee of the Side cowl,
In addition, I decorated Under Cowl other holes. (And if you feel it is too much, you can remove it later.) 。
Looks good for amateur work, just like the Image. (Since the inside is not visible at a glance.) 。
It has been a year since they were installed and there have been no problems with dislodging or warping.
It is simply a decoration, but it changes the impression of the appearance, and I am satisfied with the cost performance. (Self-satisfaction) 。
The extra mesh seat is kept as a spare.
View detail
It's not what I originally intended, but...
There are conversion collars that convert M10 to M8 and M8 to M6, but it was difficult to find one that converts M10 to M6, so we used this one for a trial.
Fixing is difficult, but M6 will fit without gaps.
If the original purpose is vibration isolation or cord protection, the M10 hole is perfect.
View detail
Manufacturer difference for Silencer
I bought this 95mm silencer spring because it seemed to fit to fix the Trickster Shotgun silencer to the exhaust pipe of my Wyvern ClassicR.
The length is perfect and the Spring is easy to install because one side has a Swivel hook and the other side turns. I have purchased a different size in the past, but the Material:It is a recommendation because Spring is made of Stainless Steel and has good durability. 。
Spring hook for installation (tool) It is easier to have a
View detail
A wide variety of size variations to choose from
Multiple patterns of OD, ID, and thickness are available for use in various places.
This time Webike had M10Size in stock and I was planning to purchase other products, so I bought it as well.
Size, texture, etc. are perfect.
It was a great help because it was a hassle to go all the way to the Motorcycle supply store to buy the Size, which was not available at the nearby Home center.
It is not worth the hassle and cost to select and buy each Size, so if I wanted, I would have to pay 3,000 yen for a Quantity that contains multiple items and is less expensive.:I wish I had a Set product.
View detail
Good to keep it from loosening
I purchased this product for Exhaust System fixed Bolt.
The lock is tight and will not loosen, so it can be used safely in any location where there is vibration.
View detail