Reviews
Fits: HONDA MONKEY125, HONDA PCX, HONDA ADV150, HONDA CRF250L, HONDA CBR250RR, HONDA X-ADV, HONDA NC750X, HONDA CBR1000RR-R
Used for CRF250L in 2023
I bought this Connector to get ACC/GND from the Optional connector on the Headlight coverReverse side.
The shape was fine and the power supply was taken out perfectly.
If you want to get power around the Handlebar, use this Connector to complete the wiring around the Headlight, so it is easy to change the Large.
View detail
Stronger and easier to use than double-sided tape
[How is it used?
YAMAHA XJR400R (07 year) DAYTONA/D-UNIT and AS UOTANI's SP2 were installed on the
KITACO's Surface Fastener was used to secure these two to the vehicle body.
When changing the wiring arrangement, double-sided tape loses its adhesive strength the next time it is peeled off.
How was your experience with it?
Size was measured in advance and we knew that this product would be sufficient.
The adhesive part is quite strong, stronger than double-sided tape.
Also, the Fastener part was well made and could be fixed well.
How did it compare to other products?
The double-sided tape that originally came with D-UNIT had weak adhesion and the mounting area was slightly sloped, so it peeled right off. However, this product seems to be large and strong as long as the fastener part does not weaken.
[Points to note]
It is recommended to degrease and install the parts using Parts Cleaner or Silicon-Off after the position to be installed is determined.
View detail
I think it's good
It is just a decoration, if you like.
There is no sense of discomfort as if it had been attached from the beginning.
It is completely self-satisfying because no one but the person himself notices it.
View detail
Used with BURGMAN 200
Used with BURGMAN 200
I lost the clip nut that holds the lid of the battery case under the foot board, so I was a little anxious about the size, but I bought it.
There was a 0.5mm hole gap between the battery case and the case, but I was able to install the case without any problem.
View detail
Height adjustment
I bought a used rear caliper support and used it to adjust the height because the wall thickness was different, perhaps due to a difference in spec.
The Swing Arm was black, so I purchased this color, which was available in the same color lineup.
It is good to measure the height and diameter in advance so that you can choose from a wide lineup of similar Sizes.
It was firmly beveled and ready to use as soon as it arrived.
View detail
V125 K5 Fork Bottom Bolt Gasket as
V125 K5 Fork Bottom Bolt Gasket as
Cheaper than buying OEM Product
View detail
be extremely thorough, focusing on even the finest of details
The mounting hole on the bracket side is an ellipse, so it can be done haphazardly.
In this case, it was used to install MONKEY's Rear Fender.
View detail
It would be helpful to have a fine Size selection.
The bracket of the Rear Sets was in the way of installing GCraft's CarbonPerafen, so we chose 20mm to shift it backward. View detail
I used it to fill in the riddle.
The Camshaft ChainHousing of the Z900RS Cylinder block has a mystery hole that is not used on this Motorcycle.
The diameter of the hole is 11mm. I have been wondering about this for a while, so I use well nuts to fill in this mysterious hole.
I hope they will continue to do so because it is a product line that raises the level of custom culture.
I used a 9.5Φ C550 with a thin neck, and since the parts are just for decoration, I used an appropriate lightweight aluminum M5 bolt and cap.
Other than the mystery hole for the cylinder block, the Center Stand mounting hole on the Left Side can also be filled with this well nut and M5 bolt since the hole diameter is 11mm.
View detail
For vibration isolation
[How is it used?
I bought this to silence the explosively cheap inferior CenterCarrier installed on my CUB, which resonates at certain RPMs and makes a lot of noise. I installed it by inserting it between the vehicle and the body.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Just pinch it in.
How was your experience with it?
The sound has disappeared. It's the best.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Not particularly
View detail
To DJEBEL.
The rubber of the gasoline cap of DF200 DJEBEL was worn out, so we cut out this rubber in a circle and installed it. View detail
For Z125 Pro Dress-up
Kawasaki Z125 Pro I was looking for a mesh seat to decorate a hole in my dreary cowl,
I found this product and bought it.
(Work procedure)
Cowl removal.
Cut this mesh seat to a suitable large size using scissors and press it against the cowl from the inside. Cut the excess part.
It is not difficult to mold with AluminumMaterial, and it can be fitted to curved surfaces to some extent.
100s Epoxy Adhesive (The one that mixes liquid 1 and 2) fixed at
At first I was thinking of decorating only the Front part and the hole around the knee of the Side cowl,
In addition, I decorated Under Cowl other holes. (And if you feel it is too much, you can remove it later.) 。
Looks good for amateur work, just like the Image. (Since the inside is not visible at a glance.) 。
It has been a year since they were installed and there have been no problems with dislodging or warping.
It is simply a decoration, but it changes the impression of the appearance, and I am satisfied with the cost performance. (Self-satisfaction) 。
The extra mesh seat is kept as a spare.
View detail
It's not what I originally intended, but...
There are conversion collars that convert M10 to M8 and M8 to M6, but it was difficult to find one that converts M10 to M6, so we used this one for a trial.
Fixing is difficult, but M6 will fit without gaps.
If the original purpose is vibration isolation or cord protection, the M10 hole is perfect.
View detail
Manufacturer difference for Silencer
I bought this 95mm silencer spring because it seemed to fit to fix the Trickster Shotgun silencer to the exhaust pipe of my Wyvern ClassicR.
The length is perfect and the Spring is easy to install because one side has a Swivel hook and the other side turns. I have purchased a different size in the past, but the Material:It is a recommendation because Spring is made of Stainless Steel and has good durability. 。
Spring hook for installation (tool) It is easier to have a
View detail
SEROW225 WE Blinker used to replace relay.
SEROW225 WE used to replace the Relay for the BlinkerHigh flasher countermeasure. It fits perfectly to the Connector on the car body side, so it can be set back to NORMAL. The quality is satisfactory. View detail
Lightweight Compact
Used with CROSS CUB (JA45).
OEM Helmet holders are hardly available, so we use this Wire and then Helmet holders.
This wire makes the OEMHelmet holder worth using.
View detail
Refresh
We replaced it for Refresh to Timing removing Cowl.
There is a feeling of reduced squeaking.
There's nothing wrong with replacing it before it cracks!
The removed items were cured.
View detail
The coloring is nice.
Daily commute to work (except when it rains during the workday) Since I have been riding, MORIWAKI's band faded in less than half a year, so I searched webike and found this site.
Branded products since it is a part of the body that is seen every day (TSR and brembo) I thought about using the "K" series, but I decided to go with the "K" series because it is a consumable product that is exposed to rain, wind, & sun.
I was concerned because the KIJIMA products I had worn before were inexpensive but looked a little bad in terms of sewing and appearance, but when I finally received them, I was impressed by their solid construction.
For a while, I used to use Bear's Wrist Band instead, but after a month, the fluff became noticeable and looked bad, but I did not see any such problem with this product after more than a month.
In any case, the MASTERBand is a consumable item, and since it is not expensive, replacement in 3-4 months should be sufficient.
View detail
Used for Koken:Mechanical Clutch Holder
What made you decide to buy?
Roller Type Micro Switch used in Koken's Mechanical Clutch Holder to fit 6ROEMClutch switch.
[How was the installation?
Coupler and terminal are Quantity:This is a set of products. I was worried about the attached terminals, so I bought only the spare terminals in case I made a mistake. When you are temporary caulking, it is important to make a good shape of Heart to get a good finish. Also, be sure to check the type of terminals on the female and male side of the coupler, as they differ.
How was your experience with it?
Since it has the same shape as the 6ROEMClutch switch, the clutch switch function can be used simply by removing and replacing the OEMCoupler. (Please check CouplerMale and Female side before working.) It is also recommended because it is the same color, so there is no sense of discomfort.
View detail
Aluminum Collar
I always use Aluminum Collar.
Anodized is also solid.
View detail