Reviews
It is usable enough. Soft but not tight enough to lick.
It is often written that the six corners become rounded, but when I tightened them with the torque wrench by pressing the tool firmly, the corners were indeed slightly deformed, but not to the extent that they became impossible to tighten.
If you say you can't install it, it's probably because of poor workmanship.
If you discount it as a cheap product, it's not bad at all.
View detail
I like the stuff, but I didn't need it for crf250rally….
Purchased when replacing crf250rallyBlinker
Rear blinkerMinus side connector is not the same shape as the light blue or Orange one, so I thought I could use it on the Plus side,
The Minus side is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Convenient
It is useful when you are not comfortable with drilling a hole to fasten a bolt or directly affixing with double-sided tape.
Examples of use include Income's Fix and Paste Type's Add Meter.
Especially when additional Meteretc. are attached with this, it is quite easy to attach and detach when something happens to Wiring-related.
View detail
In Repair.
Installation was easy and problem free! View detail
Fantastic...
These small spacers are fantastic! The finish on the anodising and precision of the maching is perfect and they come in these wonderful little packages that are a joy to look at. They were great value too, compared to other options I looked at. Would highly recommend these if you are looking for spacers. View detail
Flashing installation
Purchased as a Spacer because the Blinker turns up
It might have been a safe win, but it turned out to be in front.
View detail
I've heard that OEMs are concerned about Rust.
When I replaced the master cylinder cap, I was concerned about the Rust on the pure Normal Thread Screw, so I purchased this one.
The delivery was fast and Large satisfactory, and after the exchange it is very cool without any discomfort.
Thank you very much!
View detail
It's beautifully made.
I purchased this for my Yamaha SEROW which has a round external Silencer installed.
I made my own back guard to be attached to the silencer to protect the back for long touring. I have been using this product for a long touring, but I have to replace my round silencer band with an oval silencer band because the stainless steel is very hard and it is difficult to use it for other shapes. In my experience, it takes a long time to bend stainless steel by hand or to form it into an oval shape, and the result is not good. Unfortunately, the round Silencer band has been put into temporary storage.
The product itself is fine and well made; it is made of 1mm Stainless steel flat plate machined to 110 pie inside diameter. The bracket is raised vertically from the circular shape and is hammered to hold a right angle. The cap bolt is 25mm long, 7.7mm in diameter, and only needs an 8mm mounting hole. The Elastic band is not just a black flat rubber band, but is made with a horizontal gap to prevent it from moving. The bottom of the engraved Bracket is clearly marked 110 Pi. This kind of workmanship is very helpful when you own several similar parts.
It is relatively easy to make round-shaped bands made of gold where there are machine tools, and other manufacturers also offer a variety of bands. KITACO is a good company that sells at a cost like ConveniencePartsSeries.
View detail
It was used for the production of the preliminary Tank.
I made a spare tank and used it to take out the Fuel Hose. m6Tap was cut and welded because I was afraid of leakage. View detail
It's kind of expensive.
I used to buy Vinyl tape for around 100 yen and used it for wiring, but after a few years the surface became sticky and I didn't like it, so I bought Harness tape, which is a little more expensive, and rewound it. I am looking forward to the future. View detail
for RepairWiring
Great cosmetics I wanted a Wiring like this and it was just what I needed. View detail
I wanted a Stopper in the middle.
I used it on a Gasoline sub tank, it's useful for connecting hoses together, but it's a bit unreliable plastic, so you don't want to use pliers or anything like that when installing it.
A stopper in the middle would have made it easier to use. I'd rather have an aluminum one or something.
View detail
KITACO Needle SIMM set 3×6×0.3/0.6
Used to improve Kyanopi's mid-range speed.
I think it is good because it is cheap and effective.
View detail
It's good.
It is available at most motorcycle supply stores.
Parts replacement, etc.
I replace them when the dimensions change, etc.
View detail
safety material
Product Name
K-CON KITACOConvenienceParts K-CON Blinker/Tail Lamp Conversion Harness Set
Item Number
0900-755-01104
Vehicles
NINJA400
Number of man-hours
5 minutes depending on the work
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
For the sake of pimping.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
It's for pimping, so it's easy!
How was your experience with it?
I'm glad it works properly. Well worth the price.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Replace from attached terminal
[How is it used?
The terminal attached to GALE SPEED's Clutch holder is Straight Type
It looks ugly as it is (see photo 1), so I was wondering if there is anything better.
I was looking for it and found this!
Was the one you received as per Image?
It was exactly as pictured, nothing different.
Was the installation difficult?
Just pull it out and replace it.
Terminal to terminal connections can be made without problems with crimped pliers and a little bit of skill.
How was your experience with it?
Looks much better (see photo 2).
If you don't care, you won't care.
If you're going to mess with Motorcycle, you want the details to look nice and cool.
The terminals that come with the Parts are perfectly functional, though.
Recomendation because just a little bit of time and effort will improve the appearance of the product.
A terminal is just a terminal, but if a single terminal can change the appearance so much, it is worth replacing it.
[Included Parts:were they on?
None, just terminals and cords.
[Was there anything that disappointed you?
None in particular,
View detail
To stop Rust.
XSR900 has bolt holes for carriers? I didn't want the bolt holes to rust, so I put them on.
Gold in casual places is nice.
View detail
A friend of old cars?
I'm not sure about current vehicles, but this is a common two-turn Bullet Type Terminal on older vehicles.
I get the impression that there are a lot of them, especially around Tail.
View detail