Reviews
BIGSize!!
I use it to fix sub-computers, voltmeters, oil temperature meters, thermometers… and other electronic devices that I have installed in my car. It is easy to attach and detach, yet it is very strong! View detail
Length and Working Space
We needed to change the Bolt that holds the Exhaust System in place, so we went with this one.
I would have been happy with one, but it's not perishable, so I'll keep it in the Screw box in case I use it someday.
View detail
I made a mistake in the size and couldn't use it, but I'm making it Stock.
[How is it used?
Generator fixed bolt from Nabe Screw during EngineO/H of YAMAHA/TZr50R.
I bought this one with the intention of replacing it.
The result was not usable because of the wrong Size, but we are using it as a Stock for something else.
How was your experience with it?
I think the quality is good enough.
How did it compare to other products?
I don't have anything to compare it to, but I wonder if the price is higher than Home centeretc.
There are many types of this kind of products, so it is easier to find them on Net.
[Points to note]
nothing special
View detail
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
For mounting bolt on Generator cover
I bought it for mounting bolt of Generator cover of CUB series Engine.
The bolt under the Left is the same length, but the main reason I purchased this bolt is because the OEM bolt here is stuck in the back, so it is difficult to insert the tool.
View detail
I lost it, so...
The push rivet that stops the side cowl of YZF-R1 was lost, so I bought it.
SizeExactly.
I looked at the Touring and a little bit of the Circuit and had no problems at all.
View detail
It's good.
It is available at most motorcycle supply stores.
Parts replacement, etc.
I replace them when the dimensions change, etc.
View detail
One of the best items I've purchased!
I am glad I purchased this product because it is stronger than the typical Magic tape.
I used it to reinforce the inside of my helmet and also attached it to my speaker.
Since it is Magic tape, it can be used for a variety of purposes!
View detail
I can rely on them in times of need!
The Bolt of the Brake Caliper was rusted, so it was Refreshed with KITACOConvenienceParts (M8×40 P1.25).
The Caliper used is a YamahaOEMbrembo.
Since I could not search the OEM Parts List (no parts appeared), I first tried to remove one from Caliper, measured the Bolt size standard with Caliper, and then searched and purchased the Bolt with WeBig.
The torque for installation was measured beforehand with a KTC digital ratchet and was approximately 50 Nm, so it was tightened accordingly.
KITACOConvenienceParts is a great help when you have an itch or need help.
It's just a small part, but I'm glad it's clean!
View detail
Purchased for Wiring
This time, I needed to do Wiring for Circuit.
Purchased
The strength of the product is also solid and problem-free.
View detail
Purchased for Wiring
This time, I needed to do Wiring for Circuit.
Purchased
The strength of the product is also solid and problem-free.
View detail
Support for free shipping
I bought the Surface Fastener to meet my total before the free shipping, and I've been using it in my daily life, not only for cars and motorcycles. View detail
Stronger and easier to use than double-sided tape
[How is it used?
YAMAHA XJR400R (07 year) DAYTONA/D-UNIT and AS UOTANI's SP2 were installed on the
KITACO's Surface Fastener was used to secure these two to the vehicle body.
When changing the wiring arrangement, double-sided tape loses its adhesive strength the next time it is peeled off.
How was your experience with it?
Size was measured in advance and we knew that this product would be sufficient.
The adhesive part is quite strong, stronger than double-sided tape.
Also, the Fastener part was well made and could be fixed well.
How did it compare to other products?
The double-sided tape that originally came with D-UNIT had weak adhesion and the mounting area was slightly sloped, so it peeled right off. However, this product seems to be large and strong as long as the fastener part does not weaken.
[Points to note]
It is recommended to degrease and install the parts using Parts Cleaner or Silicon-Off after the position to be installed is determined.
View detail
Used with BURGMAN 200
Used with BURGMAN 200
I lost the clip nut that holds the lid of the battery case under the foot board, so I was a little anxious about the size, but I bought it.
There was a 0.5mm hole gap between the battery case and the case, but I was able to install the case without any problem.
View detail
be extremely thorough, focusing on even the finest of details
The mounting hole on the bracket side is an ellipse, so it can be done haphazardly.
In this case, it was used to install MONKEY's Rear Fender.
View detail
To DJEBEL.
The rubber of the gasoline cap of DF200 DJEBEL was worn out, so we cut out this rubber in a circle and installed it. View detail
It's not what I originally intended, but...
There are conversion collars that convert M10 to M8 and M8 to M6, but it was difficult to find one that converts M10 to M6, so we used this one for a trial.
Fixing is difficult, but M6 will fit without gaps.
If the original purpose is vibration isolation or cord protection, the M10 hole is perfect.
View detail
No complaints except CenterGap.
I used it on the Handlebar Clamp of my Bonsai Motorcycle. The part where the Hexagonal Wrench is inserted is gapped from the center, but there is no rattle at all, so it can be tightened firmly with Torque. I think it is a good cost performance to replace the rusted bolt as it gets rusty. View detail
Spring resonance subsides.
I was concerned about the sound of the Spring installed at the connection points of each part of the Exhaust System resonating while driving. My car's spring was not equipped with an anti-vibration rubber tube, so I purchased this spring. After checking the length and thickness of your car's Spring, you will be able to choose the one that fits it.
Since the Tube and Spring are Exactly and Fit, it is better to apply a small amount of lubricant when installing the Tube and Spring for better workability.
After installation, I am satisfied with the effect and Large change.
View detail
diversion
I bought it for my SCUB, so this time it is a push rivet, but I used it for my PCX because the push rivet was damaged when I changed the battery of my PCX. I wish it was a little more cost-effective. View detail