Reviews
It cannot be used for Shinobi Sen Cowl (crying).
It's my fault for not checking carefully, but I bought the upper 6 push rivetsfor replacement of the front under cowl on my 2014NINJA1000, but the inside rivet size was thicker than the OEM Product and did not fit in the holes&hellip I bought this rivet for replacement for the upper 6 push rivetsfor the front under cowl of my 2014 NINJA1000.
For your information, the correct OEM Product number is 92039-0068. to
View detail
Just in case.
It may not be an option, but Neck is the pricey one for this kind of thing. View detail
Vibration prevention
It is a re-purchase to attach to the Spring part used for the ChamberFlange part at the time of maintenance.
The product is not bad, but it would be helpful if the price per pc. was a little lower.
View detail
Fixing Screw
I bought it to try it out, wondering if it could be used to fix Cowl. The materialAluminum was nice, but the tapping screw and the length of the screw seem to limit its use.
It would be helpful if you could sell regular Screws, available in a choice of lengths.
View detail
Bolt replacement for MirrorOffsetHolder
Currently, I am using the low type of DAYTOMA's Hi-Viz Mirror and the shorter version of Tanax's Mirror Offset Holder. It is not impossible to fasten the OffsetHolder with other items, but it was not good for my mental health, so I decided to replace it.
However, I have never seen a 1.25 cap bolt, which is often used for motorcycles, at a home center, and I have to order one from a shop specializing in screw bolts by mail order. You have to order from a shop specializing in screw bolts by mail order, or buy from KITACO or Posh. In this case, I only needed to purchase two bolts, and since I did not have any other bolts or nuts that I needed, and since I was not Timing for bulk purchases, I chose KITACO's products instead of ordering from ScrewShop because of the shipping cost. I wanted a black one, if possible, so I hesitated between a black one and a black one from Posh, but I decided to buy a KITACO product because it was a little bit cheaper. The bolt itself is a good product that can be used normally without any problem, but I think the price is too expensive.
By replacing the Bolt with a 5mm longer Bolt, the Bolt is now firmly in place and secure. We recommend replacing the bolt with a new one if you have similar concerns.
View detail
desorption
I bought this to fix Screen to prevent scratches and for easy removal.
The price was reasonable, but the diameter and length were not quite right. The diameter and length did not fit well.
View detail
For fixing plastic parts and
I thought, "Can't I use it to fix the Screen? The price was reasonable, so I bought it.
It was impossible due to the thickness of the fixed section and lack of length.
It can be used in other fixtures and will be used there.
View detail
Size did not match ADV150
It was meant for Honda, but it was not available because it did not match the size of the push rivet used on the ADV150.
I think it is a normal product for a push rivet.
View detail
For Drain boltWiring
No problem for Wiring
I should have bought a larger size because it was far from Drain bolt....
View detail
Screw Change
The Rear Sets mounting position was changed, and since the Spacer was changed, the Fixing Screws were changed.
Rust resistant Material:Stainless Steel, the length was just right to secure it.
View detail
Stainless bolt
The installed screws were not stainless steel, but old, so we replaced them with rust-resistant stainless steel screws.
Screw size, type and what I needed was helpful because I could choose what I needed.
View detail
Stainless bolt
The bolt installed was not stainless steel, so it was changed to this stainless steel to prevent rusting.
The look and feel of this Stainless Steel has become a good feeling.
View detail
Purchased with Sponge sheet
When repairing an OEMOption engine slider, we decided to replace the sponge that comes in contact with the cowl because it had also deteriorated. The thickness of the double-sided tape is 0.4mm, including the backing paper. 0.4mm
After making a base paper and cutting it out of Seat, I tried to stick Double-sided Tape to Sponge Sheet, but the adhesive strength was weak and it peeled off easily. I tried applying pressure with my fingers to make it stick, but when I peeled off the other side of the backing paper, the double-sided tape body also peeled off. The thinness of the double-sided tape also makes it easy to gap, and the double-sided tape will overlap, so please be careful when handling it.
After attaching it to the engine slider, we left it for 24 hours until it was fully adhered. After that, when I touched it, it was firmly adhered, so I felt relieved for the time being. Immediately after bonding, the adhesive is not stable. Please allow enough time for the adhesion to be stable.
View detail
On License Plate Bolt
I wanted to put a round Sticker on the License Plate Bolt, and I'm glad I found just the right one. View detail
Quick and easy to get the right Size
They are conveniently available in numbers without being cheap in quality. I would like to see them in packs of four each, even if the price goes up. View detail
exchange
Because the Rubber of the ChamberFlange part Spring use had deteriorated, it is purchase here for Replacement.
Installation was fine and the Material seems to be Silicon, so I expect it to be durable.
Quantity:It would be helpful if they were sold at a lower price, such as 1 Set of 2pcs.
View detail
For the installation of ETC Antennas
[How is it used?
I used this when I relocated the ETCAntennas on my newly switched XJR1300C.
Was the one you received as per Image?
I have bought this product in the past and it was as Image.
How was your experience with it?
I think it's a little raised tall. It feels like it's going to be munimini after you put it on.
The adhesive strength is not that great, so be careful not to take it off and put it on again and again, because it will become shabby!
[Points to note]
If you cut it too small, it will lose adhesion to Velcro, so it's best to keep it somewhat large.
I put KTC's Ratchet on the picture to make it easier to understand the largeness.
View detail
To Cowl.
I used it to fix Cowl.
It can be used if the hole diameter and depth match.
View detail
Package for additional purchase
I don't have a little Bolt! It would be convenient if there is a home center or a gold shop nearby that sells bolts in bulk, but it's not always easy.
I'm lucky to be able to buy it at Site, but I don't think it's very cosy because there are so few of them.
Plating is regular Uniqlo. I use it on the parts that get rusty, but it seems to have a thicker coating than the cheapest product because no rust comes up in about 2 months.
However, the one I installed on my exhaust pipeCover was covered in rust within a month. In high temperature environment, it will be damaged just like other Bolt.
View detail
No particular feature
It's a very ordinary Uniqlo plating Bolt.
You can choose Pitch, so be careful not to make a mistake.
In my case, the fixed bolt of Silencer had disappeared before I knew it, and I bought it hurriedly as a replacement, so I was satisfied if the pitch was right. If I say a detailed point, when I buy the same etc. goods of Uniqlo plating at Home center etc., because it is about 1 pc50 yen, it is rather expensive.
The surface treatment is very strong and there is no rust on the surface after one month of installation.
It's an unadorned Bolt, but if you're not particularly particular about it, there's no harm in buying it along.
View detail