Reviews
One of the best items I've purchased!
I am glad I purchased this product because it is stronger than the typical Magic tape.
I used it to reinforce the inside of my helmet and also attached it to my speaker.
Since it is Magic tape, it can be used for a variety of purposes!
View detail
exchange
The connection connector of the main power supply was old, and its removal and installation was strange.
TAB, receptacle, and Terminal Set, so it is much easier to remove and install with the new replacement.
View detail
Reflector should be attached.
I had a Fender Eliminator on my Axis Treat and cut the bracket that mounts the OEMReflector under the Number, so I stuck this product on the rear bracket part of the Pillion Bar of the Wills WIN.
The size is just right and the quality seems to be durable, unlike the ones sold in the 100s.
The double-sided tape provided with the product is a very strong adhesive, so it is best to position it firmly before attaching.
View detail
Outside of Motorcycle.
There are many kinds of RepeatThailand products on the market, including cheaper ones, but this one is easy to release and use.
I would like to see a variety of lengths available.
View detail
There are many different sizes.
You don't need impressions.
You will get Points, so please stay with us.
[How is it used?
Silencer BracketI just wanted to let it out a little.
Was the one you received as per Image?
And I've seen the actual thing at Image itself Naps.
Was the installation difficult?
It was so easy that I was surprised.
How was your experience with it?
That was great.
[Included Parts:were they on?
It came with an outer bag.
[Was there anything that disappointed you?
None at all.
View detail
Older Vehicles on Rubber PartsReplace
[How is it used?
old car (SportsCUB) Used to attach to 6V MONKEY/GORILLA Main Harness at Restore of
Was the one you received as per Image?
Measure the OEM's size in advance and arrange for the closest size.
As a matter of course, I received exactly what was described in Size.
How was your experience with it?
It is a very ordinary ConnectorCover, so it's neither too good nor too bad.
Since different sizes are lineuped, it is nice to be able to choose a close size when replacing parts that are no longer available.
View detail
This is for Bullet Terminal of HondaSmall Type car.
[How is it used?
old car (SportsCUB) Used in Restore of
Was the one you received as per Image?
The Sleeve is also thick and easy to use.
Cheaper ones are usually available, but I would choose this one for its quality of workmanship.
Was the installation difficult?
Electric Works Pliers can be attached if available.
It is no different from a normal Size Bullet Terminal.
[Was there anything that disappointed you?
While not disappointing, it would be better if there was also a Package with a slightly larger quantity and less expensive pricing.
View detail
I can rely on them in times of need!
The Bolt of the Brake Caliper was rusted, so it was Refreshed with KITACOConvenienceParts (M8×40 P1.25).
The Caliper used is a YamahaOEMbrembo.
Since I could not search the OEM Parts List (no parts appeared), I first tried to remove one from Caliper, measured the Bolt size standard with Caliper, and then searched and purchased the Bolt with WeBig.
The torque for installation was measured beforehand with a KTC digital ratchet and was approximately 50 Nm, so it was tightened accordingly.
KITACOConvenienceParts is a great help when you have an itch or need help.
It's just a small part, but I'm glad it's clean!
View detail
For repairing faulty wiring View detail
Oil cooler fixtures
When installing the UniversalOil cooler, I wanted to install the included hose, but the One Side can only be installed by cutting the Pipe, and the companion of the included hose is a Crimp, so I tried my best to modify it, but it was impossible, so I changed the hose to a Rubber type. I tried to modify the hose but it was impossible, so I decided to change the hose to a rubber type.
I also wanted to install an oil temperature sensor on the Meter, so I bought this one after much deliberation.
We changed to HoseType, so the length and handling are now free.
It works normally
It is difficult to say "normal" because normal use is a matter of course, but the quality has to be good.
I can buy the quantity I want as a Single Item and it is Reasonable. I hope you will continue to offer products like this in the future.
View detail
For UniversalMeter installation
In replacing the Meter with KOSO's Multimeter, we did not want to damage the harness on the body side, so we purchased a 110-type 9-pole and 3-pole Coupler and made an intermediate harness so that the new Meter could be detached with the Coupler.
The product was a perfect fit, the terminals were solid, and the product was safe to use. The coupler is compatible with the coupler attached to the harness on the body side of the car without any problem, and it can be attached and detached smoothly.
I think it was a bit of a waste since I only used One Side, but I will keep the extra one in a Large Cutout until I need it some other time.
View detail
Low Torque Location
Material:The aluminum anodized parts were about to be bald, so I inserted them between the parts.
It's just right to use it on Cowl for scratch protection.
It's a very solid object.
View detail
Replace each time when replacing Oil
I purchased the washer for the drain bolt part because I was told that it should be replaced as needed when changing the oil.
OEM Product may be correct, but Other Brand Product is easier to procure, and since it is only a washer, there is not much difference between the two.
View detail
Performance and price are sufficient for your needs.
[How is it used?
Used to disassemble and clean the rear master cylinder of a YAMAHA XJR400R.
How was your experience with it?
Nothing is impossible.
I believe that the basic performance of these products will remain the same.
How did it compare to other products?
This item is 1 bagQuantity:1 Set of 2pcs. but other products are available in Large quantity and cheaper.
However, DailyMechanic like me only uses it occasionally, so I think this one is sufficient.
[Points to note]
If Torque management is not done properly, Brake fluid will leak and ooze, so be sure to do it properly.
View detail
Offset firmly in place.
[How is it used?
I used it when I changed the Silencer on my YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86.
The Φ14 thinner Silencer band is now farther away and cannot be handled by the existing Bolt.
So we measured the amount of gap and purchased this product to offset the aluminum collars on the rear suspension mounting and silencer band side.
How was your experience with it?
The measurements were perfect and the Offset was solid.
We also did a good Torque management on the fixation, so I don't think there is any problem.
How did it compare to other products?
It was Large strange to find a product that fits Exactly because various Manufacturers are offering similar products.
I have the impression that this product had the best price and Size development.
You can buy them at Home center, but basically you should buy them at motorcycle supply stores or on the webike.
I think it's good
[Points to note]
nothing special
View detail
for adjustment
Repurchased to add a step on the Screen I had previously put on. View detail
Buy Bore Up Kit for Repair!
[How is it used?
The Clip that came with the Bore Up Kit contained only the minimum necessary and was insufficient during maintenance, which led to its purchase.
How was your experience with it?
BALI is a concern, but if it is used with BALI removed as described in the Instruction Manual, it can be used without problems.
How did it compare to other products?
It is more difficult to fit than the e-type Pin from Mukawa or Clipping point, but I think Orthodox is more stable and less likely to come off.
[Points to note]
If it fails, it will fly away and you will not know where it went.
I think it would be tough to take it out once it is inside the Crankcase.
▼It seems that inventory is running low, but if it goes out of use, maintenance will not be possible.
It would be sad to see Repair Parts become a valuable part of the old car category any longer.
View detail
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Exactly!
This time, I had to buy it in a hurry because the Carrier RANBolt I was installing had come off and was missing.
I was just about to add a screw lock material, but the other side was still there, so I measured the size and purchased a bolt at a nearby home center!
Screw lock material was also added!
View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail