Reviews
6V For compatibility with Large type terminals that supply power to MONKEY/GORILLA Main Harness
I bought a battered 900SS (900SL) and am Restore.
The car body was stored in a high humidity environment, so it was also battered by corrosion, but the humidity also entered the inside of the Harness and corroded the core wire in the cord, which was also battered.
Cut the damaged part, create a new Harness, and make a new Connector.
In the end, we had to redo the connector as the center of the connector, because moisture would penetrate and corrode from the area where it is crimped by the terminals in the connector.
When redoing a Connector, play it back in the existing Connector whenever possible.
It's a method of removing corroded terminals from a Connector and replacing only the terminals.
However, if the terminals are corroded, conduction resistance is created and heat is generated, which may cause the ConnectorBody to burn or melt.
Pinch especially Large-type Connectors with Large current flow when they are corroded.
So, this Connector, which is the source of the Large that supplies Battery power to 6V MONKEY/GORILLA Main Harness, was looking a bit iffy, so we replaced it with a new one.
Since it is a standardized product, it is fully interchangeable, and even if it is necessary to replace the harness again for some reason in the future, it can be interchanged without a hitch.
The milk-white Connectors seem to have a tendency to crack over time due to heat and UV rays, but the milk-white OEM Connectors have withstood 30 years without cracking, so I am sure this one will be large and durable.
View detail
The quality is good and can be used without problems!
Active (ACTIVE) I purchased this product for Repair because I damaged the Electro Tap of my company's LEDNumberSIDEBlinker. It works fine and the quality is good! As with all Electro Tap products, it is not waterproof at all, so please use it in a place where it will not be exposed to water! View detail
Replace from attached terminal
[How is it used?
The terminal attached to GALE SPEED's Clutch holder is Straight Type
It looks ugly as it is (see photo 1), so I was wondering if there is anything better.
I was looking for it and found this!
Was the one you received as per Image?
It was exactly as pictured, nothing different.
Was the installation difficult?
Just pull it out and replace it.
Terminal to terminal connections can be made without problems with crimped pliers and a little bit of skill.
How was your experience with it?
Looks much better (see photo 2).
If you don't care, you won't care.
If you're going to mess with Motorcycle, you want the details to look nice and cool.
The terminals that come with the Parts are perfectly functional, though.
Recomendation because just a little bit of time and effort will improve the appearance of the product.
A terminal is just a terminal, but if a single terminal can change the appearance so much, it is worth replacing it.
[Included Parts:were they on?
None, just terminals and cords.
[Was there anything that disappointed you?
None in particular,
View detail
Older Vehicles on Rubber PartsReplace
[How is it used?
old car (SportsCUB) Used to attach to 6V MONKEY/GORILLA Main Harness at Restore of
Was the one you received as per Image?
Measure the OEM's size in advance and arrange for the closest size.
As a matter of course, I received exactly what was described in Size.
How was your experience with it?
It is a very ordinary ConnectorCover, so it's neither too good nor too bad.
Since different sizes are lineuped, it is nice to be able to choose a close size when replacing parts that are no longer available.
View detail
This is for Bullet Terminal of HondaSmall Type car.
[How is it used?
old car (SportsCUB) Used in Restore of
Was the one you received as per Image?
The Sleeve is also thick and easy to use.
Cheaper ones are usually available, but I would choose this one for its quality of workmanship.
Was the installation difficult?
Electric Works Pliers can be attached if available.
It is no different from a normal Size Bullet Terminal.
[Was there anything that disappointed you?
While not disappointing, it would be better if there was also a Package with a slightly larger quantity and less expensive pricing.
View detail
For repairing faulty wiring View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail
H4の前面にプラグをキャップで固定し、衝撃を防ぐために使用します。まあ、それは多くのモデルで使用できます。 View detail
For installation of Grip heater (Crimp available)
Used to install Grip heater.
SUZUKI ADDRESS110, I used it to connect from Attachment power supply to Grip heater power supply.
The only work to be done is to install the Wiring and terminals of the Grip heater into the Coupler using a Crimp to ensure that Plus and Minus are not mistaken, and connect it to the Attachment power supply on the car body side.
I have been using Grip heater for about a month and have been able to use it without any problems.
View detail
emergency measure
Finally, the end-Quantity:The Thailand coil of GB250 CLUBMAN's clutch wire broke and I used it as a first aid kit. The wire was out of order at the point where it was cut, so I used an on-board tool to adjust the tip and cut the end-quantity.:I inserted it into the set and fastened it with the included Hexagonal Wrench. I was surprised that it worked better than I expected, and it is a good thing to have one with you when touring. I learned a lot this time because I can work faster if I have a nipper to adjust the wire. I will add a Nipper to my on-board tools. View detail
Bullet Terminal for Motorcycle
I searched several mass retailers for a CB103 Honda type Bullet Terminal for my motorcycle, but could not find one, so I searched webike and found it. I searched webike and found it and bought it. Thank you very much for your wide variety of products.
The Bullet Terminal for Motorcycle is small. (I didn't know)
As for the product, it is an ordinary Bullet Terminal and I have no particular impression of it.
View detail
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650. (The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650.
(The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion screw of the blinker lens of 250TR.
Since an authentic positive one is iron and it is easy to rust, parts are replaced to the tapping screw made from a stainless!! YO from which the tapping screw for the pure blinkers of a zephyr system or a vulcan system is incidentally also set to M4x25.
We did two-piece (a total of 8) acquisition of the product here, and were taken as the screw of the blinker lens of order.
*) -- The stock case of W650 becomes the relay of 12V/15W.
Relay exchange becomes indispensable when diverting the blinker of other vehicles to W650.
Relay #27002-1101 for 12V/21W (product blinker conversion-code made from posh is followed.) = Kawasaki original manufacturer's product
.
.)
View detail
There is no problem
It is a good product in general, and I chose it because I imagined it would be more resistant to deterioration over time than the White color. View detail
It is stiff and helpful.
Since the clutch lever, wire, and routing, etc., have been replaced, it may be that the mounting points are subjected to forces in odd directions, or it may be that the quantity has already been reduced.:2pc. Set ruined.
The clutch can be cut without it, but it is smoother with this cover. As other reviewers have mentioned, if the installation method is correct, there is a little bit of hang.
I have one squishy one a year, but I always Stock it because of the price. I really appreciate the fact that you can provide these parts.
View detail
For branching to Gasoline Reserve Tank
I used this product as a branch to Gasoline reserve tank. The grooves are cut so it is easy to use and the hose does not come loose. View detail
Brake terminal is still this one.
After all, it's not a flash in the pan for Brake switch unless it comes with this flag-shaped protective Vinyl.
Note that the vinyl insert is a bit long and must be pushed in to fit.
Also, Wiring is horribly hard.
View detail
Thank you for the good product
Thank you for the good product. I used this to enlarge the size of Yamaha's rz50 battery. The result is satisfactory and the fit is good. View detail
for OEM battery connect
ENG: people who sell giorno to me, they cut the battery wire and change the cables akwardly haha so i must recover all harness so i decide use original connecter and battery so this is it ready to use condiction just put some bullet connecter and cover some tape and done! KOR: The previous owner modified the battery harness to fit a larger battery. I want to install a genuine battery. The battery is not genuine and the floor panel does not close. So I prepared a battery and prepared a connector View detail
K con cable Tube mark . super quality
I'm looking for genuine quality products.this the one what I need .good quality blabel mark . soft sleeve and sharp marking.highly recommended product.thaks k-con. View detail
K con insulation tube .super quality
Super quality flexible and high durability.this my 2nd order.last year brought one still using without hard and still flexible.highly recommended product.thaks k con. View detail