Reviews
For everyday use
I bought this for regular use for Repair because the Throttle Wire on my old Motorcycle broke and OEM Parts were out of business and there was nothing I could do about it.
Screw lock was used for the Thailandoko fixing Screw, and the Thailandoko was fixed Firmly with a Solder at the root of the Thailandoko.
View detail
6V For compatibility with Large type terminals that supply power to MONKEY/GORILLA Main Harness
I bought a battered 900SS (900SL) and am Restore.
The car body was stored in a high humidity environment, so it was also battered by corrosion, but the humidity also entered the inside of the Harness and corroded the core wire in the cord, which was also battered.
Cut the damaged part, create a new Harness, and make a new Connector.
In the end, we had to redo the connector as the center of the connector, because moisture would penetrate and corrode from the area where it is crimped by the terminals in the connector.
When redoing a Connector, play it back in the existing Connector whenever possible.
It's a method of removing corroded terminals from a Connector and replacing only the terminals.
However, if the terminals are corroded, conduction resistance is created and heat is generated, which may cause the ConnectorBody to burn or melt.
Pinch especially Large-type Connectors with Large current flow when they are corroded.
So, this Connector, which is the source of the Large that supplies Battery power to 6V MONKEY/GORILLA Main Harness, was looking a bit iffy, so we replaced it with a new one.
Since it is a standardized product, it is fully interchangeable, and even if it is necessary to replace the harness again for some reason in the future, it can be interchanged without a hitch.
The milk-white Connectors seem to have a tendency to crack over time due to heat and UV rays, but the milk-white OEM Connectors have withstood 30 years without cracking, so I am sure this one will be large and durable.
View detail
for BlinkerBullet Type Terminal replacement
I bought a battered 900SS (900SL) and am Restore.
The body of the car is in shambles, but the Harness is fine! There is no such thing as a "wiring".
The 900SL (900SS is the same) has a front blinker embedded in the cowl, which is unusual for a sports type motorbike, and is connected to the 6V MONKEY/GORILLA Main Harness with a Bullet Type Terminal. The front blinker is embedded in the cowl, which is unusual for a sports type motorbike.
However, the Connector uses not only the Bullet Type Terminal, but also an ultra-thin Flat Terminal to connect the BlinkerBody to the Harness.
This is the same as the Flat Terminal of the stop lamp switch used in the front master cylinder, and is an example of a terminal that can break off if handled carelessly.
Bullet Type Terminals can be very difficult to remove when fitted tightly.
When pulling in a narrow cowl, it is easy to pull Wiring as hard as you can with the momentum of the pull out.
If the momentum breaks the ultra-thin terminal that connects to the BlinkerBody, it will be Large strange!
Parts are still available, but they are expensive (nearly $10,000 for One Side) and we must try not to break them!
That's where this Connector comes in.
The original Bullet Terminal is left in place and a very short Connection Connector is made, and the 110-type Connector is used for connection and disconnection.
This way, the valuable Blinker body is not destroyed because it does not require monstrous strength to pull it out.
In this case, it is a non-polarized part, so it is fine, but this Connector is not reversible, so it is also ideal for parts that require polarity.
You can make a lot of progress just by stopping Bullet Terminal and using this Connector!
View detail
The quality is good and can be used without problems!
Active (ACTIVE) I purchased this product for Repair because I damaged the Electro Tap of my company's LEDNumberSIDEBlinker. It works fine and the quality is good! As with all Electro Tap products, it is not waterproof at all, so please use it in a place where it will not be exposed to water! View detail
Replace from attached terminal
[How is it used?
The terminal attached to GALE SPEED's Clutch holder is Straight Type
It looks ugly as it is (see photo 1), so I was wondering if there is anything better.
I was looking for it and found this!
Was the one you received as per Image?
It was exactly as pictured, nothing different.
Was the installation difficult?
Just pull it out and replace it.
Terminal to terminal connections can be made without problems with crimped pliers and a little bit of skill.
How was your experience with it?
Looks much better (see photo 2).
If you don't care, you won't care.
If you're going to mess with Motorcycle, you want the details to look nice and cool.
The terminals that come with the Parts are perfectly functional, though.
Recomendation because just a little bit of time and effort will improve the appearance of the product.
A terminal is just a terminal, but if a single terminal can change the appearance so much, it is worth replacing it.
[Included Parts:were they on?
None, just terminals and cords.
[Was there anything that disappointed you?
None in particular,
View detail
Outside of Motorcycle.
There are many kinds of RepeatThailand products on the market, including cheaper ones, but this one is easy to release and use.
I would like to see a variety of lengths available.
View detail
Older Vehicles on Rubber PartsReplace
[How is it used?
old car (SportsCUB) Used to attach to 6V MONKEY/GORILLA Main Harness at Restore of
Was the one you received as per Image?
Measure the OEM's size in advance and arrange for the closest size.
As a matter of course, I received exactly what was described in Size.
How was your experience with it?
It is a very ordinary ConnectorCover, so it's neither too good nor too bad.
Since different sizes are lineuped, it is nice to be able to choose a close size when replacing parts that are no longer available.
View detail
This is for Bullet Terminal of HondaSmall Type car.
[How is it used?
old car (SportsCUB) Used in Restore of
Was the one you received as per Image?
The Sleeve is also thick and easy to use.
Cheaper ones are usually available, but I would choose this one for its quality of workmanship.
Was the installation difficult?
Electric Works Pliers can be attached if available.
It is no different from a normal Size Bullet Terminal.
[Was there anything that disappointed you?
While not disappointing, it would be better if there was also a Package with a slightly larger quantity and less expensive pricing.
View detail
For repairing faulty wiring View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail
Fits: HONDA MONKEY125, HONDA PCX, HONDA ADV150, HONDA CRF250L, HONDA CBR250RR, HONDA X-ADV, HONDA NC750X, HONDA CBR1000RR-R
Used for CRF250L in 2023
I bought this Connector to get ACC/GND from the Optional connector on the Headlight coverReverse side.
The shape was fine and the power supply was taken out perfectly.
If you want to get power around the Handlebar, use this Connector to complete the wiring around the Headlight, so it is easy to change the Large.
View detail
SEROW225 WE Blinker used to replace relay.
SEROW225 WE used to replace the Relay for the BlinkerHigh flasher countermeasure. It fits perfectly to the Connector on the car body side, so it can be set back to NORMAL. The quality is satisfactory. View detail
Used for Koken:Mechanical Clutch Holder
What made you decide to buy?
Roller Type Micro Switch used in Koken's Mechanical Clutch Holder to fit 6ROEMClutch switch.
[How was the installation?
Coupler and terminal are Quantity:This is a set of products. I was worried about the attached terminals, so I bought only the spare terminals in case I made a mistake. When you are temporary caulking, it is important to make a good shape of Heart to get a good finish. Also, be sure to check the type of terminals on the female and male side of the coupler, as they differ.
How was your experience with it?
Since it has the same shape as the 6ROEMClutch switch, the clutch switch function can be used simply by removing and replacing the OEMCoupler. (Please check CouplerMale and Female side before working.) It is also recommended because it is the same color, so there is no sense of discomfort.
View detail
For installation of Grip heater (Crimp available)
Used to install Grip heater.
SUZUKI ADDRESS110, I used it to connect from Attachment power supply to Grip heater power supply.
The only work to be done is to install the Wiring and terminals of the Grip heater into the Coupler using a Crimp to ensure that Plus and Minus are not mistaken, and connect it to the Attachment power supply on the car body side.
I have been using Grip heater for about a month and have been able to use it without any problems.
View detail
emergency measure
Finally, the end-Quantity:The Thailand coil of GB250 CLUBMAN's clutch wire broke and I used it as a first aid kit. The wire was out of order at the point where it was cut, so I used an on-board tool to adjust the tip and cut the end-quantity.:I inserted it into the set and fastened it with the included Hexagonal Wrench. I was surprised that it worked better than I expected, and it is a good thing to have one with you when touring. I learned a lot this time because I can work faster if I have a nipper to adjust the wire. I will add a Nipper to my on-board tools. View detail
For emergency spare parts and maintenance of old cars
[How is it used?
TZr250R (3XV) I purchased this as a spare/for replacement for the Throttle Wire of
We chose this product because it was inexpensive and the Size feel seemed fine.
Was the one you received as per Image?
L-Type Wrench is included as shown in the photo.
Since it takes up very little bulk, it is convenient to carry as a spare.
How was your experience with it?
It is stored in the storage space under the Tandem seat for emergency use when touring.
Fortunately, we have not yet encountered a SCENE to use.
TZr250R (3XV) In the case of the "Oil Pump", the OEM Product is discontinued and there is no Replacement Product due to the complexity of splitting the 1 pc Wire into a carburetor, YPVS, and Oil pump.
Many used ones are also in poor condition, and since they are consumable parts that will have to be replaced at some point, they will not be wasted as long as you continue to ride because you will eventually use them when that time comes.
[Points to note]
It would be nice to have a Wire cutter to adjust the length.
How did it compare to other products?
The delivery time was so long that I also bought a No Brand product sold at a certain Large Hand NetShop just in time.
Fortunately, I have not used either of them, but the No Brand product did not come with tools, so I think this product is better for emergency use. I think this one is better for emergency use.
【Review】
Although it is best not to use it, it is a product that can be soldered for emergency use or for long-term use, so it will not go to waste.
I have had to push Motorcycle for an hour in the past because the Wire ran out, so it is a good idea to have it with you to avoid that kind of feeling.
View detail
for the occasion
[How is it used?
I bought this when I was organizing my commuter CUB Wiring, which has been a mess since I bought it, for Earth.
Was the one you received as per Image?
As per Image, AutoBacks and Color:I could have gone to YellowHat to buy them, but it was a hassle, so I bought them at Webig while buying other parts. It is very helpful to be able to buy something on the side.
Was the installation difficult?
Crimping with Electric Works Pliers is OK. As a side note, Electric Works Pliers are KNIPEX's recommendation for extra-thick pliers. Cheaper types have a thinner body and cannot be crimped properly.
Wiring relationships work best if you buy Electric Works Pliers that are as tough and thick as possible.
Rob Star (Shrimp) I remember that the good ones of the "Mere Old Man" were also so-so and thick.
How was your experience with it?
Neither good nor bad
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Electric Works Pliers can last a lifetime if you buy the right ones, so go ahead and splurge!
View detail
Bullet Terminal for Motorcycle
I searched several mass retailers for a CB103 Honda type Bullet Terminal for my motorcycle, but could not find one, so I searched webike and found it. I searched webike and found it and bought it. Thank you very much for your wide variety of products.
The Bullet Terminal for Motorcycle is small. (I didn't know)
As for the product, it is an ordinary Bullet Terminal and I have no particular impression of it.
View detail
Fits: HONDA CBR1000RR-R, HONDA NC750X, HONDA X-ADV, HONDA CBR250RR, HONDA CRF250L, HONDA ADV150, HONDA MONKEY125, HONDA PCX
after my purchase
It was good that the delivery was fast. It came early. Why do you keep urging me to write down my review?It was good that the delivery was fast. It came early. Why do you keep urging me to write down my review? View detail
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650. (The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion
The product of a kitaco is TSU which is only a product saved cheaply and joyfully!! Custom-made plan of the blinker of W650.
(The 1) TSU which is appropriation wearing about the blinker of 250TR W650!! First of all, it is exchange about the conclusion screw of the blinker lens of 250TR.
Since an authentic positive one is iron and it is easy to rust, parts are replaced to the tapping screw made from a stainless!! YO from which the tapping screw for the pure blinkers of a zephyr system or a vulcan system is incidentally also set to M4x25.
We did two-piece (a total of 8) acquisition of the product here, and were taken as the screw of the blinker lens of order.
*) -- The stock case of W650 becomes the relay of 12V/15W.
Relay exchange becomes indispensable when diverting the blinker of other vehicles to W650.
Relay #27002-1101 for 12V/21W (product blinker conversion-code made from posh is followed.) = Kawasaki original manufacturer's product
.
.)
View detail