Reviews
BIGSize!!
I use it to fix sub-computers, voltmeters, oil temperature meters, thermometers… and other electronic devices that I have installed in my car. It is easy to attach and detach, yet it is very strong! View detail
Length and Working Space
We needed to change the Bolt that holds the Exhaust System in place, so we went with this one.
I would have been happy with one, but it's not perishable, so I'll keep it in the Screw box in case I use it someday.
View detail
I made a mistake in the size and couldn't use it, but I'm making it Stock.
[How is it used?
Generator fixed bolt from Nabe Screw during EngineO/H of YAMAHA/TZr50R.
I bought this one with the intention of replacing it.
The result was not usable because of the wrong Size, but we are using it as a Stock for something else.
How was your experience with it?
I think the quality is good enough.
How did it compare to other products?
I don't have anything to compare it to, but I wonder if the price is higher than Home centeretc.
There are many types of this kind of products, so it is easier to find them on Net.
[Points to note]
nothing special
View detail
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
For everyday use
I bought this for regular use for Repair because the Throttle Wire on my old Motorcycle broke and OEM Parts were out of business and there was nothing I could do about it.
Screw lock was used for the Thailandoko fixing Screw, and the Thailandoko was fixed Firmly with a Solder at the root of the Thailandoko.
View detail
6V For compatibility with Large type terminals that supply power to MONKEY/GORILLA Main Harness
I bought a battered 900SS (900SL) and am Restore.
The car body was stored in a high humidity environment, so it was also battered by corrosion, but the humidity also entered the inside of the Harness and corroded the core wire in the cord, which was also battered.
Cut the damaged part, create a new Harness, and make a new Connector.
In the end, we had to redo the connector as the center of the connector, because moisture would penetrate and corrode from the area where it is crimped by the terminals in the connector.
When redoing a Connector, play it back in the existing Connector whenever possible.
It's a method of removing corroded terminals from a Connector and replacing only the terminals.
However, if the terminals are corroded, conduction resistance is created and heat is generated, which may cause the ConnectorBody to burn or melt.
Pinch especially Large-type Connectors with Large current flow when they are corroded.
So, this Connector, which is the source of the Large that supplies Battery power to 6V MONKEY/GORILLA Main Harness, was looking a bit iffy, so we replaced it with a new one.
Since it is a standardized product, it is fully interchangeable, and even if it is necessary to replace the harness again for some reason in the future, it can be interchanged without a hitch.
The milk-white Connectors seem to have a tendency to crack over time due to heat and UV rays, but the milk-white OEM Connectors have withstood 30 years without cracking, so I am sure this one will be large and durable.
View detail
for BlinkerBullet Type Terminal replacement
I bought a battered 900SS (900SL) and am Restore.
The body of the car is in shambles, but the Harness is fine! There is no such thing as a "wiring".
The 900SL (900SS is the same) has a front blinker embedded in the cowl, which is unusual for a sports type motorbike, and is connected to the 6V MONKEY/GORILLA Main Harness with a Bullet Type Terminal. The front blinker is embedded in the cowl, which is unusual for a sports type motorbike.
However, the Connector uses not only the Bullet Type Terminal, but also an ultra-thin Flat Terminal to connect the BlinkerBody to the Harness.
This is the same as the Flat Terminal of the stop lamp switch used in the front master cylinder, and is an example of a terminal that can break off if handled carelessly.
Bullet Type Terminals can be very difficult to remove when fitted tightly.
When pulling in a narrow cowl, it is easy to pull Wiring as hard as you can with the momentum of the pull out.
If the momentum breaks the ultra-thin terminal that connects to the BlinkerBody, it will be Large strange!
Parts are still available, but they are expensive (nearly $10,000 for One Side) and we must try not to break them!
That's where this Connector comes in.
The original Bullet Terminal is left in place and a very short Connection Connector is made, and the 110-type Connector is used for connection and disconnection.
This way, the valuable Blinker body is not destroyed because it does not require monstrous strength to pull it out.
In this case, it is a non-polarized part, so it is fine, but this Connector is not reversible, so it is also ideal for parts that require polarity.
You can make a lot of progress just by stopping Bullet Terminal and using this Connector!
View detail
The quality is good and can be used without problems!
Active (ACTIVE) I purchased this product for Repair because I damaged the Electro Tap of my company's LEDNumberSIDEBlinker. It works fine and the quality is good! As with all Electro Tap products, it is not waterproof at all, so please use it in a place where it will not be exposed to water! View detail
For mounting bolt on Generator cover
I bought it for mounting bolt of Generator cover of CUB series Engine.
The bolt under the Left is the same length, but the main reason I purchased this bolt is because the OEM bolt here is stuck in the back, so it is difficult to insert the tool.
View detail
I lost it, so...
The push rivet that stops the side cowl of YZF-R1 was lost, so I bought it.
SizeExactly.
I looked at the Touring and a little bit of the Circuit and had no problems at all.
View detail
It's good.
It is available at most motorcycle supply stores.
Parts replacement, etc.
I replace them when the dimensions change, etc.
View detail
Replace from attached terminal
[How is it used?
The terminal attached to GALE SPEED's Clutch holder is Straight Type
It looks ugly as it is (see photo 1), so I was wondering if there is anything better.
I was looking for it and found this!
Was the one you received as per Image?
It was exactly as pictured, nothing different.
Was the installation difficult?
Just pull it out and replace it.
Terminal to terminal connections can be made without problems with crimped pliers and a little bit of skill.
How was your experience with it?
Looks much better (see photo 2).
If you don't care, you won't care.
If you're going to mess with Motorcycle, you want the details to look nice and cool.
The terminals that come with the Parts are perfectly functional, though.
Recomendation because just a little bit of time and effort will improve the appearance of the product.
A terminal is just a terminal, but if a single terminal can change the appearance so much, it is worth replacing it.
[Included Parts:were they on?
None, just terminals and cords.
[Was there anything that disappointed you?
None in particular,
View detail
One of the best items I've purchased!
I am glad I purchased this product because it is stronger than the typical Magic tape.
I used it to reinforce the inside of my helmet and also attached it to my speaker.
Since it is Magic tape, it can be used for a variety of purposes!
View detail
Outside of Motorcycle.
There are many kinds of RepeatThailand products on the market, including cheaper ones, but this one is easy to release and use.
I would like to see a variety of lengths available.
View detail
Older Vehicles on Rubber PartsReplace
[How is it used?
old car (SportsCUB) Used to attach to 6V MONKEY/GORILLA Main Harness at Restore of
Was the one you received as per Image?
Measure the OEM's size in advance and arrange for the closest size.
As a matter of course, I received exactly what was described in Size.
How was your experience with it?
It is a very ordinary ConnectorCover, so it's neither too good nor too bad.
Since different sizes are lineuped, it is nice to be able to choose a close size when replacing parts that are no longer available.
View detail
This is for Bullet Terminal of HondaSmall Type car.
[How is it used?
old car (SportsCUB) Used in Restore of
Was the one you received as per Image?
The Sleeve is also thick and easy to use.
Cheaper ones are usually available, but I would choose this one for its quality of workmanship.
Was the installation difficult?
Electric Works Pliers can be attached if available.
It is no different from a normal Size Bullet Terminal.
[Was there anything that disappointed you?
While not disappointing, it would be better if there was also a Package with a slightly larger quantity and less expensive pricing.
View detail
I can rely on them in times of need!
The Bolt of the Brake Caliper was rusted, so it was Refreshed with KITACOConvenienceParts (M8×40 P1.25).
The Caliper used is a YamahaOEMbrembo.
Since I could not search the OEM Parts List (no parts appeared), I first tried to remove one from Caliper, measured the Bolt size standard with Caliper, and then searched and purchased the Bolt with WeBig.
The torque for installation was measured beforehand with a KTC digital ratchet and was approximately 50 Nm, so it was tightened accordingly.
KITACOConvenienceParts is a great help when you have an itch or need help.
It's just a small part, but I'm glad it's clean!
View detail
For repairing faulty wiring View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail
Purchased for Wiring
This time, I needed to do Wiring for Circuit.
Purchased
The strength of the product is also solid and problem-free.
View detail