Reviews
Ideal for blowby gas extraction
The basic application is as shown in the Title. However, it is too thin to be used for cars and motorcycles with high engine displacement volume, which may result in poor performance and malfunctions.
The durability of the paint is unknown, so it was rated 3 Stars.
View detail
Instead of Indicator's Window shade
[How is it used?
PlugWindow shade on YAMAHA XJR400R Indicator? (OEM number:16G-13569-00) Because of the AISCancellation, I had to blind the place where the hose was originally attached, so I used this instead.
How was your experience with it?
The size was a little short in height and the inside diameter was not quite right and a little loose.
The Clip on the Horse was used to prevent it from coming off while driving.
How did it compare to other products?
I finally repurchased the OEM because I was afraid of sucking secondary air due to the thinner Rubber and slightly looser inner diameter compared to the OEM number:16G-13569-00. However, I had no problem using it as a substitute.
[Points to note]
The inner diameter is loose and must be stopped with a Clip or inHemp palmock.
View detail
I bought this because I wanted to take the negative pressure out of the Manifold.
I drilled a hole in the manifold and cut a tap to attach the negative pressure pump. View detail
Oil catch
About quality and texture It was better than I thought About the feeling of use I was very satisfied and connected as I thought Products to buy together Will vary as needed Difficulty of installation There was no problem installing it Cost performance and comparison with other products The price is good and the parts are good About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing SHIFT UP: : I installed it in Oil Shower Bullet Camshaft Holder and I thought it was needed because it seemed to come out more than I thought View detail
It can be exactly used for the output side of the oil cooler of an ape.
It can be exactly used for the output side of the oil cooler of an ape. View detail
It is small and is an L type oil nipple 90 degrees. It is used for extension of the breather nipple of the engine of 4mini. Since extraction of a breather is made to a smart and it is easy to adjust the extraction angle of a hose, it is recommende
It is small and is an L type oil nipple 90 degrees.
It is used for extension of the breather nipple of the engine of 4mini.
Since extraction of a breather is made to a smart and it is easy to adjust the extraction angle of a hose, it is recommended very well.
They are parts which can be dramatically used considering a price.
View detail
It purchased as an output side of the oil cooler of an ape. If it is those who understand the location in which a hole is made, and a size, it can be perfectly used by OK.
It purchased as an output side of the oil cooler of an ape.
If it is those who understand the location in which a hole is made, and a size, it can be perfectly used by OK.
View detail
On the 2nd strike Oil line.
TZr250R (3XV) I bought this product because I thought there might be a possibility that the oil hose might be clogged or broken, etc. during the Restore of the
As a result, I had no problem with the OEM Oil nipple, so I will keep it as a spare.
I think Small is just right for use in the 2-stroke Oil line.
View detail
Well finished with a durable coating
Nothing fancy but well crafted and finished. I used it to connect my oil cooler to my engine which worked well. No leaks or any issues. View detail
I bought it to relocate the oil hose to the intake manifold.
KITACO's KEIHINPE24carburetor has a separate oil nipple for oiling, but I had to remove the oil hose every time I removed the carburetor.
The carburetor side is covered with a rubber cap.
View detail
As a Cap for Negative Pressure Ejection Nipple
When I purchased the negative pressure outlet (Vito R&Negative Pressure Ejection Nipple Item No.:314-99-001) for Carburetor, I was able to use it with no problem, although it was a little tight.
Perhaps the Size under this (3.2mm) Then it's too tight, Size on this (4.4mm) Then I think it's too loose to fit in.
Cut and use as there is plenty of room in the length.
I think you should apply a little Silicon grease to prevent it from sticking after use.
Seemingly expensive, but less expensive than other similar products.
View detail
Oil line change
Although the carburetor was exchanged, the diameter of the Oil nipple changed and it had to be converted
Thanks to using it, I am satisfied that the same function can be reproduced while leaving Hose so far
View detail
I made a mistake in buying Size (6. 4X9. 5X25)
In order to fill Negative Pressure Nipple of outside company carburetor and Intake manifold, inside diameter 5. 5X8. I thought of buying 5 X 25 mm, I mistook the Size to buy (Lol). I tried fitting Nipple which I was planning to use actually, and it was a little Large drunkard. Well, I think that there are not too many Nipples that Fit even with this Size, so you can use it somewhere ...
Quantity : 1 Set of 2pcs. With 200 yen a little and Cost performance is also good, detailed dimensions are also described, so you can purchase with confidence. It is good to choose Size in detail finely.
There is a case that you should not use Oil or Gasoline to stop Oil or Gasoline in the product's note, but if it fills the negative pressure, is it Large Durable?
Previously, when using Rubber cap attached with a bonus of DAYTONA 's Power Filter for negative pressure padding, it had cracked and smoked the secondary air in about six months.
This product is 2 Tolyl Material : Because it is Rubber, it seems that it will not be a problem so much with respect to oil resistance, but durability may not be expected, so I'd like to keep it stocked regularly.
The way to make the product is not practical because it is a practical Parts, but I feel a little bit BALI and a cheap feeling of Material.
However, when you think to buy such Cap, it is saved unexpectedly even at the Motorcycle supplies store and the home center, so feel free to buy it with webike.
You can substitute Hose folded with Tie Wrap, but because it looks bad it is better that Cap is better.
View detail