Reviews
No loose ends!
I was looking for a M8, Stainless Steel, low profile nut with a non-loosening nut. I looked in Home center, but they don't have a Pitch 1.25. I looked in Home center, but they don't have a 1.25 pitch. 1.25 is non-negotiable because it is for a CUB that has a lot of vibration. I searched for a lot of options and bought 3 kinds of lock nuts from ConvenienceParts by KITACO.
Loosening stop is Friction ringType. The long formal name is new to me; I used to call it a UNut or a feathered nut. The feathers are used to apply torque to the bolt. When used on a long bolt, the load is too much and the feather is bent completely. Then the Torque will not be applied. As a result, the loosening stop does not work. It is not advisable to reuse a nut with bent wings.
I checked the size, pitch, and construction of the wings, and they are all fine. I have used 3 types of normal featherless parts with different parts, and even with 3 types, if they are feathered rather than featherless, the tightness is fine. I added a SpringWasher just in case. The height increased by that amount.
The instruction manual explains the length of the protrusion from the nut. This time, the protrusion is one notch, or less than 1mm, and it says that it can be used for other parts as well, since it says that it is large sturdy up to 5mm. Personally, I don't use winged nut for bolt that needs to be tightened and loosened many times. I don't often put on and off Torque rods, so I prefer to use them for my own purposes. [Color] Clear.
It has traveled more than 1000 km after installation. I did not use screw lock agent because it is stainless steel. I don't need screw lock agent this time.
View detail
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
I used it to fill in the riddle.
The Camshaft ChainHousing of the Z900RS Cylinder block has a mystery hole that is not used on this Motorcycle.
The diameter of the hole is 11mm. I have been wondering about this for a while, so I use well nuts to fill in this mysterious hole.
I hope they will continue to do so because it is a product line that raises the level of custom culture.
I used a 9.5Φ C550 with a thin neck, and since the parts are just for decoration, I used an appropriate lightweight aluminum M5 bolt and cap.
Other than the mystery hole for the cylinder block, the Center Stand mounting hole on the Left Side can also be filled with this well nut and M5 bolt since the hole diameter is 11mm.
View detail
Refresh
We replaced it for Refresh to Timing removing Cowl.
There is a feeling of reduced squeaking.
There's nothing wrong with replacing it before it cracks!
The removed items were cured.
View detail
Thank God they don't sell them at the homestore.
When I installed NAMETALCraft's aluminum chain guard on Over Racing's Swing Arm, the bolt nut on the reverse side was dangerous because it interfered with the chain when I fixed it with the bolt on the front side bracket. I inserted a 12mm Truss Screw from the Reverse side and fixed it with this Cap Nut with Flange from the outside using an AngleDriver. After that, there was no more interference and I am satisfied with the result.
This was helpful because these special Nuts are not sold in Home center.
View detail
Cheaper than OEM
We purchased more because they are cheaper than OEM!
When they are old, they are hardened and I replace them when they are Rose.
This is a necessary component to prevent Cowl from cracking or over-tightening!
View detail
Less expensive than OEM Parts
[How is it used?
I used it to fix my newly purchased Chinese Cowl.
I bought this product because it was inexpensive and had good reviews.
Was the one you received as per Image?
I purchased For M6, but it is surprisingly Large, so it is somewhat troublesome to extend the lower hole.
Was the installation difficult?
The Chinese Cowl originally has an appropriate hole Size, so the hole needs to be expanded.
The work must be done carefully because it has to be made rather Exactly.
It is recommended because it is easy to use once it is fixed.
How was your experience with it?
It is strong enough to fix Cowl.
As mentioned above, Chinese Cowl would be useful as long as the pre-drilling is done properly. (Actually, I prefer Quick fastener, but...)
Note that the price is surprisingly high when used in large quantities. Still, it is much cheaper than OEM parts.
[Was there anything that disappointed you?
Although the product itself is not so great, the size is indicated as large, but I thought it was difficult to image the size.
I felt it would be easier to buy if compatible OEM Parts numbers were listed.
【Review】
It is useful for fixing exterior parts such as Cowl and Screen.
OEM Parts are expensive, so if you want to keep the price as low as possible, this is a good option.
View detail
Half the price of OEM
It had not been replaced for a long time, so it hardened and lost its damper effect, so it was replaced for refresh!
I was quoted to buy OEM, but it cost twice as much as KITACO product, so I decided to buy KITACO product.
I am Large satisfied with this one because it is cosier!
View detail
Good quality
Better quality than Home center, etc.
I would like to see Lock nut in Nylon as well.
View detail
Thin type
I purchased this low profile lock nut because the length of the bolt to which the Exhaust System is attached was too long for the normal thickness lock nut to fit over the Limit Screw.
Thanks to this, I was able to tighten it without any problem and I am satisfied.
View detail
Cap Nut with internal lock
This is a Cap Nut with an internal lock.
There is no worry about falling off while driving.
Recommendation
View detail
Exhaust Nut, anti-dropout measures.
It will be used for the Stud bolt next to the Exhaust Gasket. 。 Apply OmegaOil's BlueGrease to the screw part for rust prevention. 。 I plan to use it with SpringWasher! 。 Tightening Torque will be half of the specified value (because of applying Grease.) 。 It's to prevent the Exhaust Nut from falling out. 。 If you've ever dropped out, how about giving it a try? View detail
Clearance.
Rear master between Swing Arm and Rear Sets
Yes, because Clearance is usually in contact with Nut.
I was looking for a thin Nut.
Stainless SteelMaterial with Lock nut.
It was the right material!
View detail
Hidden Dress-upItems!
There are so many little parts to We-Big, and it's fun to research and plan out all the details! KITACO and ConvenienceParts have a wide range of products for motorcycles. There are a lot of screws and plastic parts that can be Isn't this good for dress-up? There are some beautiful Parts that look like this. This time I found this 24K Plating, SUS Cap Nut with Flange! I wasn't sure if I could put it on my car Grom, but I bought it, and even though I bought two bags That's 1,200 yen! Cheap compared to other dress-up parts!
The first aim is to replace the Cap Nut that fixes the exhaust pipe to the cylinder. It was a However, because of the length of the Stud bolt, the Long Type Nut was still used. This Nut made by KITACO seemed to be able to tighten it, but it was too much. Because it was like a Limit, I decided not to turn on the Exhaust System. Since the frequency of removal is quite high, this Nut is getting painful. So I'm looking for a strong and clean nut, but if it's not a Cap Nut, the Stud bolt is not I'm worried that it might rust. But Material:Titanium's and the like are just regular Nut with a popping tip.
On the other hand, this Cap Nut and the perfectly sized Cap Nut from KITACO are used in four It is the head cover of Engine. Before installing it, I cleaned the bolt and installed the head cover. I applied a small amount of MOTOREX CuCompound before tightening it up. It may not be as hot as the pipe part, but I think it still gets quite hot, so bite prevention is essential.
What do you think? It's beautiful! It doesn't match the color of the surrounding gold alumite parts, but this one in 24K Plating Real gold color. I wonder how long this shine will last, but I'm sure it's stronger than Anodized. It may not be able to be used on every car, but you can make this kind of customization with some creativity. It is possible. For the Large size of the effect, it's very cheap! Please visit ConvenienceParts to find a beautiful part that will fit your vehicle! Please!
View detail
Mostly successful
Cowl fixed well nut rotted
In OEM, Quantity:1 Set of 10pcs.
The rottenness is 1pc.
Quantity:2pc. Set
We were able to get the desired number of items for KITACO Universal Product
View detail
For the purpose of improving beauty
AGRAS : Screw is heavy to install the Racing slider
Because we used Titanium's long Bolt, it is bag-like so that the Screw part does not protrude for the purpose of preventing danger and improving aesthetic appearance Nut. KITACOConveniencePartsK-CON : I used Cap Nut with Flange.
It also becomes Dress-up
View detail
Purchase
Hexagon Nut of M10 is located in the neighborhood's home center Pitch 1. I bought a thing of KITACOConvenienceParts with only 5 things. M10P1. I was able to use it without problems with 25. KITACOConvenienceParts are rich in variety and useful. View detail
Just Convenience Parts
【Purchase motive】
I'm doing the desorption work of Mirror of FZ 1 FAZER and the corner of OEM's M6 Nut fixing Molror's Bolt has been shaved, : I found this item when I found a similar Nut in Stainless Steel.
【attachment】
I replaced it with OEM's Nut, so Fitting made no mistake.
[Others]
- From OEM's iron, Material : I think that there is almost no worry about rust becoming Stainless Steel.
- Since I think that there is a similar Nut as it is at the home center, there is a sense of security for those who installed it as a part for Motorcycle.
- The price is also Quantity : 1 Set of 2pcs. I think that it is valid if it is this place.
View detail