Reviews
For Mount bar mounting
[How is it used?
For rare vehicles that do not have a dedicated AttachmentMount bar,
Used to tighten the Bracket together with the Switch Box.
Was the one you received as per Image?
I have purchased this product in the past when it was processed on another vehicle,
The quality of the product is very low, and I think it's a perfect Spacer product.
Was the installation difficult?
Both inner and outer diameters are exactly the same as indicated, so it is a simple installation.
How was your experience with it?
The outer diameter is exactly the same size as the head of a Bolt with a hexagonal hole,
It fits in the bolt hole of the SW-BOX EXACTLY as we intended to use it.
[Included Parts:were they on?
Included Parts:No setting
[Was there anything that disappointed you?
There is none
Other items that would be helpful
Since the only colors available are Silver and Black,
It would be nice to have other colors.
View detail
As expected of a ready-made product
I thought I could make it myself, but this time I bought it. It was a bit expensive. I'm glad I bought it because it turned out just like the image. View detail
alignment
I tried to install NPRO Ject's Twin muffler on my WR250X, but the Clutch Side interfered with the ZeroGee Tail cowl, so I chose this one to keep it off the outside.
It is better mentally than piling on the appropriate Washer or Bolt.
View detail
Good texture and usability
The Front Fender of CRF250RLY50 is very low front, so when I run Course and other aggressive driving, the front tire and the Front Fender contact each other at the Full Bottom. I use this 5mm Spacer on the rear two of the four Fender fixing points to change the angle.
It's very good.
The strength and precision are perfect.
View detail
High quality and value for money
I used this to adjust the angle of Windshield of CRF250RALLY50. I put a 25mm Spacer on it and it looks good. If it is longer than 25mm, it will be a problem to fix the screen, so 25mm is the limit.
The beautiful anodized black color of KITACO's aluminum spacer blends well with the black of the OEM front cowl stay of the CRF250RLY50.
View detail
The main point is that the outer diameter is larger than that of a regular collar.
I bought a battered 900SS (900SL) and am Restore.
The footpeg was made by Menani, but it was too battered, so we used parts from various manufacturers that we managed to put together to form the footpeg.
However, when I installed it, the footpeg mount on the frame side seems to be distorted only on the Right Side, and it slightly goes too far inside the vehicle body.
Left has about 5mm gap between footpeg and Swing Arm, but Right has only about 2mm...
As expected, it was too narrow, so we tried to optimize it by inserting a 3mm-thick Spacer between the footpeg and the Frame.
That is fine, but the contact area with the footpeg was small because the outer diameter of the spacer is a normal size.
I don't know what's wrong with that, but it bothered me, so I exchanged it for a Spacer with a larger outer diameter!
That is the product here.
The difference is slight.
However, those who laugh at it as slight are not qualified to talk about Tuning...so I feel good!
In fact, if you replace the Spacer only on the One Side, you will feel more like you are EXACTLY doing it.
I don't see anyone doing that.
The increased contact area should have increased the rigidity of the installation, but nothing can be felt.
Well, it's OK because it's self-satisfying.
The performance of Spacer itself is perfect.
Some hard Material (maybe in the 6000's based on machinability and Anodized's coloring? Mystery) and smooth surface.
0.It would be very nice to be able to purchase 1pc. units of Spacer for use on car bodies, unless there is a need for accuracy in 1mm increments!
View detail
Good thickness that you can understand only when you put it on.
CUB90 with external Swing Arm.
I am adjusting the Rear to get the Line. Similarly, the Torque rod of the Rear brake also needs adjustment, so I purchased an aluminum spacer from KITACO.
Both length and thickness are as described. The chamfering is also well done, and the circumference of the aluminum cut-out is well made and beautifully finished. I like to look at something that is clean and good quality. This is just my feeling, but since it is used for the torque rod of the rear brake, I think this level of quality is fine. This time, due to the size, the quantity is limited.:2pc. Set purchased and connected to use.
I had to modify it a bit because the Spacer makes slight contact with the welded Sauce. We first measured and chose a spacer that could be installed, but it was not the right thickness. The measurement is a very small error, but it is a very large job.
It would be nice if all the parts could be diverted from Honda's OEM products, but it is difficult when other brand products are involved as in this case. KITACO offers many kinds of spacers, so it is very helpful. The size indication is written in Illustration on the back of the package. The Scale is also printed on the back of the package so that you can measure the parts you have. This is a very nice feature.
View detail
In Repair.
Installation was easy and problem free! View detail
Fantastic...
These small spacers are fantastic! The finish on the anodising and precision of the maching is perfect and they come in these wonderful little packages that are a joy to look at. They were great value too, compared to other options I looked at. Would highly recommend these if you are looking for spacers. View detail
Flashing installation
Purchased as a Spacer because the Blinker turns up
It might have been a safe win, but it turned out to be in front.
View detail
There are many different sizes.
You don't need impressions.
You will get Points, so please stay with us.
[How is it used?
Silencer BracketI just wanted to let it out a little.
Was the one you received as per Image?
And I've seen the actual thing at Image itself Naps.
Was the installation difficult?
It was so easy that I was surprised.
How was your experience with it?
That was great.
[Included Parts:were they on?
It came with an outer bag.
[Was there anything that disappointed you?
None at all.
View detail
Offset firmly in place.
[How is it used?
I used it when I changed the Silencer on my YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86.
The Φ14 thinner Silencer band is now farther away and cannot be handled by the existing Bolt.
So we measured the amount of gap and purchased this product to offset the aluminum collars on the rear suspension mounting and silencer band side.
How was your experience with it?
The measurements were perfect and the Offset was solid.
We also did a good Torque management on the fixation, so I don't think there is any problem.
How did it compare to other products?
It was Large strange to find a product that fits Exactly because various Manufacturers are offering similar products.
I have the impression that this product had the best price and Size development.
You can buy them at Home center, but basically you should buy them at motorcycle supply stores or on the webike.
I think it's good
[Points to note]
nothing special
View detail
for adjustment
Repurchased to add a step on the Screen I had previously put on. View detail
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Exactly!
This time, I had to buy it in a hurry because the Carrier RANBolt I was installing had come off and was missing.
I was just about to add a screw lock material, but the other side was still there, so I measured the size and purchased a bolt at a nearby home center!
Screw lock material was also added!
View detail
Used to reduce rattling of Brake lever
[How is it used?
Brake lever was rattling badly and I bought it in hopes that it would get better.
The Touch feeling of the MASTER itself was not so good, but I suspected that maybe it was because the rattling was so bad that I could not press the Piston straight? I also suspected that it might be because I could not press the Piston straight.
To be honest, since it is a SmallEngine Displacement Volume for a foreign car, I thought that the rattling might be terrible combined with poor accuracy, but I tried it when I learned from an article on Webig that this Washer can reduce the rattling.
Was the one you received as per Image?
As you can see in the picture, it is just a Washer.
It is not a very expensive product, but the price of this thin Washer may be too expensive for some people...
Was the installation difficult?
Simply remove the Brake lever and insert it in between.
Washer is just on Lever, so it is a bit frustrating to have to Gap it back to MASTER.
How was your experience with it?
Actually, I first tried 0.3mm, but did not feel much change. 0.6mm with 2 layers of 0.3mm reduced rattling in a good way. However, I felt that the movement of Lever was a little reluctant or stuck, perhaps due to the two layers of 0.3mm, and I felt it was dangerous.:I settled on 1pc. Even with 0.5mm, there is some rattling, but it has been reduced to an acceptable level.
However, I did not see any large change in the touch feeling that I had expected, and I felt again that in such a case, I had no choice but to replace the entire MASTER.
[Included Parts:were they on?
Washer only.
[Was there anything that disappointed you?
nothing special
View detail
Height adjustment
I bought a used rear caliper support and used it to adjust the height because the wall thickness was different, perhaps due to a difference in spec.
The Swing Arm was black, so I purchased this color, which was available in the same color lineup.
It is good to measure the height and diameter in advance so that you can choose from a wide lineup of similar Sizes.
It was firmly beveled and ready to use as soon as it arrived.
View detail
It would be helpful to have a fine Size selection.
The bracket of the Rear Sets was in the way of installing GCraft's CarbonPerafen, so we chose 20mm to shift it backward. View detail
I am satisfied with this price.
GCraft's CarbonPerafen is a surface [Color] I bought it to distribute the pressure with a thin Spacer with a Large tight outer diameter because it looked like it would crack with the Bolt that came with something like Clear.
The Spacer in this Series is finely Sized, which is helpful.
View detail
For vibration isolation
[How is it used?
I bought this to silence the explosively cheap inferior CenterCarrier installed on my CUB, which resonates at certain RPMs and makes a lot of noise. I installed it by inserting it between the vehicle and the body.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Just pinch it in.
How was your experience with it?
The sound has disappeared. It's the best.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Not particularly
View detail