Reviews
For installation of Racing hook
In order to install YOSHIMURA's Silencer Bracket and Babyface's Racing hook on top of each other, we had to purchase a bolt of the appropriate length so that the Bracket and Hook could be installed at the same time, since they would interfere with each other and the Tie Down Belt would not fit.
The color was selected to match the Silencer Bracket and Hook because they are black.
After measuring the dimensions of the gap that would not interfere with the Tie Down Belt, we thought an 8mm-thick collar would be appropriate, and when we installed it, the Tie Down Belt could be easily passed through and the protrusion was as small as possible.
We chose the smallest diameter, although we were torn between 18mm and 20mm.
This collar is good because the edge corners are treated so there is no attack on the contacting Parts.
View detail
KITACO Cap Bolt Cover
The Cap Bolt Cover of the Handlebar Fixing Section of GSX-S was missing.
buy for Replacement
If you don't buy a cap bolt that fits the size of your cap bolt, it won't attach properly, so check when you buy.
I was told it was black chrome, but I think it is a little lighter and closer to silver.
I'm rating it 4 stars because the durability is unknown.
View detail
Recommended for clear tail lens Visibility
Clear tail lens is installed for visibility and safety.
It feels like it was added for the sake of it, but it's a good thing because Reflector is necessary.
View detail
Ideal for preventing damage to Number….
I noticed that the reverse side of the License Plate was getting dirty with mud and Asphalt-like substances, so I purchased this plate for two purposes:to prevent dirt from staining the plate, and to prevent damage to the License Plate since it was almost bent when the Number was caught a few times.
After installation, it is completely hidden by the License Plate, so it is not visible from the rear, but the reverse side is protected and serves as a reinforcement for the License Plate, which may be useful for Large to prevent damage.
In my case, I bought it together with ”Nasa Type Number Plate Holder Set” and did a dress-up at the same time, albeit very slightly.
The aforementioned objectives of the purchase have been fulfilled, and the rubber cap to suppress plate vibration is also a nice touch.
In my opinion, Plate seems solid, thick, and sturdy. I searched on the Net and found one with a weight of 210g in the product description. If you don't mind the slight weight of the car, I don't think it will affect your posture, but I was a little concerned about the weight of the Plate.
View detail
For Mount bar mounting
[How is it used?
For rare vehicles that do not have a dedicated AttachmentMount bar,
Used to tighten the Bracket together with the Switch Box.
Was the one you received as per Image?
I have purchased this product in the past when it was processed on another vehicle,
The quality of the product is very low, and I think it's a perfect Spacer product.
Was the installation difficult?
Both inner and outer diameters are exactly the same as indicated, so it is a simple installation.
How was your experience with it?
The outer diameter is exactly the same size as the head of a Bolt with a hexagonal hole,
It fits in the bolt hole of the SW-BOX EXACTLY as we intended to use it.
[Included Parts:were they on?
Included Parts:No setting
[Was there anything that disappointed you?
There is none
Other items that would be helpful
Since the only colors available are Silver and Black,
It would be nice to have other colors.
View detail
As expected of a ready-made product
I thought I could make it myself, but this time I bought it. It was a bit expensive. I'm glad I bought it because it turned out just like the image. View detail
alignment
I tried to install NPRO Ject's Twin muffler on my WR250X, but the Clutch Side interfered with the ZeroGee Tail cowl, so I chose this one to keep it off the outside.
It is better mentally than piling on the appropriate Washer or Bolt.
View detail
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
No loose ends!
I was looking for a M8, Stainless Steel, low profile nut with a non-loosening nut. I looked in Home center, but they don't have a Pitch 1.25. I looked in Home center, but they don't have a 1.25 pitch. 1.25 is non-negotiable because it is for a CUB that has a lot of vibration. I searched for a lot of options and bought 3 kinds of lock nuts from ConvenienceParts by KITACO.
Loosening stop is Friction ringType. The long formal name is new to me; I used to call it a UNut or a feathered nut. The feathers are used to apply torque to the bolt. When used on a long bolt, the load is too much and the feather is bent completely. Then the Torque will not be applied. As a result, the loosening stop does not work. It is not advisable to reuse a nut with bent wings.
I checked the size, pitch, and construction of the wings, and they are all fine. I have used 3 types of normal featherless parts with different parts, and even with 3 types, if they are feathered rather than featherless, the tightness is fine. I added a SpringWasher just in case. The height increased by that amount.
The instruction manual explains the length of the protrusion from the nut. This time, the protrusion is one notch, or less than 1mm, and it says that it can be used for other parts as well, since it says that it is large sturdy up to 5mm. Personally, I don't use winged nut for bolt that needs to be tightened and loosened many times. I don't often put on and off Torque rods, so I prefer to use them for my own purposes. [Color] Clear.
It has traveled more than 1000 km after installation. I did not use screw lock agent because it is stainless steel. I don't need screw lock agent this time.
View detail
KITACOConvenienceParts has been helpful.
What made you decide to buy?
Because the ZitaRacing ScreenBolt does not come with a Nylon washer!
[How is it used?
To install the Zita Racing ScreenBolt!
[How was the installation?
It is Exactly to the size of ZitaRacing ScreenBolt.
[How was it when you used it?
Rather than installing the bolt directly, just inserting a nylon washer between the bolt and the washer will help prevent scratches. I think that even if you just have it as a spare part, you can use it later on! This is a product that is not likely to be found at a nearby home center.
View detail
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
Good texture and usability
The Front Fender of CRF250RLY50 is very low front, so when I run Course and other aggressive driving, the front tire and the Front Fender contact each other at the Full Bottom. I use this 5mm Spacer on the rear two of the four Fender fixing points to change the angle.
It's very good.
The strength and precision are perfect.
View detail
High quality and value for money
I used this to adjust the angle of Windshield of CRF250RALLY50. I put a 25mm Spacer on it and it looks good. If it is longer than 25mm, it will be a problem to fix the screen, so 25mm is the limit.
The beautiful anodized black color of KITACO's aluminum spacer blends well with the black of the OEM front cowl stay of the CRF250RLY50.
View detail
The main point is that the outer diameter is larger than that of a regular collar.
I bought a battered 900SS (900SL) and am Restore.
The footpeg was made by Menani, but it was too battered, so we used parts from various manufacturers that we managed to put together to form the footpeg.
However, when I installed it, the footpeg mount on the frame side seems to be distorted only on the Right Side, and it slightly goes too far inside the vehicle body.
Left has about 5mm gap between footpeg and Swing Arm, but Right has only about 2mm...
As expected, it was too narrow, so we tried to optimize it by inserting a 3mm-thick Spacer between the footpeg and the Frame.
That is fine, but the contact area with the footpeg was small because the outer diameter of the spacer is a normal size.
I don't know what's wrong with that, but it bothered me, so I exchanged it for a Spacer with a larger outer diameter!
That is the product here.
The difference is slight.
However, those who laugh at it as slight are not qualified to talk about Tuning...so I feel good!
In fact, if you replace the Spacer only on the One Side, you will feel more like you are EXACTLY doing it.
I don't see anyone doing that.
The increased contact area should have increased the rigidity of the installation, but nothing can be felt.
Well, it's OK because it's self-satisfying.
The performance of Spacer itself is perfect.
Some hard Material (maybe in the 6000's based on machinability and Anodized's coloring? Mystery) and smooth surface.
0.It would be very nice to be able to purchase 1pc. units of Spacer for use on car bodies, unless there is a need for accuracy in 1mm increments!
View detail
To hide the hexagonal hole
Plating was peeling and falling apart, so the
Purchased to replace
It looks pretty shiny.
View detail
Good thickness that you can understand only when you put it on.
CUB90 with external Swing Arm.
I am adjusting the Rear to get the Line. Similarly, the Torque rod of the Rear brake also needs adjustment, so I purchased an aluminum spacer from KITACO.
Both length and thickness are as described. The chamfering is also well done, and the circumference of the aluminum cut-out is well made and beautifully finished. I like to look at something that is clean and good quality. This is just my feeling, but since it is used for the torque rod of the rear brake, I think this level of quality is fine. This time, due to the size, the quantity is limited.:2pc. Set purchased and connected to use.
I had to modify it a bit because the Spacer makes slight contact with the welded Sauce. We first measured and chose a spacer that could be installed, but it was not the right thickness. The measurement is a very small error, but it is a very large job.
It would be nice if all the parts could be diverted from Honda's OEM products, but it is difficult when other brand products are involved as in this case. KITACO offers many kinds of spacers, so it is very helpful. The size indication is written in Illustration on the back of the package. The Scale is also printed on the back of the package so that you can measure the parts you have. This is a very nice feature.
View detail
Copper Packing
I want to use copper packing for drain bolt when changing oil.
It was thinner and smaller than I expected.
There doesn't seem to be any oil leaks and the Seal is done, so that's good.
Quantity:1pc., cheap in terms of selling price? I wonder.
View detail
In Repair.
Installation was easy and problem free! View detail