Reviews
As expected of a ready-made product
I thought I could make it myself, but this time I bought it. It was a bit expensive. I'm glad I bought it because it turned out just like the image. View detail
alignment
I tried to install NPRO Ject's Twin muffler on my WR250X, but the Clutch Side interfered with the ZeroGee Tail cowl, so I chose this one to keep it off the outside.
It is better mentally than piling on the appropriate Washer or Bolt.
View detail
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
KITACOConvenienceParts has been helpful.
What made you decide to buy?
Because the ZitaRacing ScreenBolt does not come with a Nylon washer!
[How is it used?
To install the Zita Racing ScreenBolt!
[How was the installation?
It is Exactly to the size of ZitaRacing ScreenBolt.
[How was it when you used it?
Rather than installing the bolt directly, just inserting a nylon washer between the bolt and the washer will help prevent scratches. I think that even if you just have it as a spare part, you can use it later on! This is a product that is not likely to be found at a nearby home center.
View detail
Thinnest lock nut known
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but because it came off while driving, we thought it would be best to use a double nut to stop the nut, so we installed a longer 20mm nut than the 12mm nut that would be used for the double nut to fix the set.
This Nut is as thin as 4mm and with Lock.
It cannot be Torqueed strongly, but it is a very effective product.
Is it expensive?
View detail
Used with Babyface Change lever
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm6 12mm is tightened by Screw lock+tightening the specified Torque.:2pc. We used a set to connect the two, but since it came off while driving, we thought it would be best to use a double nut stop, and since the reverse side of the lever would be tight with 12mm, we installed a longer 20mm and then fixed this product to the reverse side.
Nut texture is good and 4mm thin is the only one I know of.
If it were a little cheaper, it would help.
View detail
This is the only m6Lock nut that is thin.
The change lever of Babyface is divided into two parts, and the Flat Cap Boltm612mm is tightened by Screw lock+tightening the specified Torque.:2pc. The set was used to connect the two, but since it came off while driving, we thought it would be best to use double nut fasteners, so we used the included 12mm to make the reverse side of the lever tight, so we used the longer 20mm to penetrate and installed this product.
Nut texture is good.
As far as I know, this is the only thin 4mm of m6Nut.
But it would help if it were a little cheaper.
View detail
Good texture and usability
The Front Fender of CRF250RLY50 is very low front, so when I run Course and other aggressive driving, the front tire and the Front Fender contact each other at the Full Bottom. I use this 5mm Spacer on the rear two of the four Fender fixing points to change the angle.
It's very good.
The strength and precision are perfect.
View detail
High quality and value for money
I used this to adjust the angle of Windshield of CRF250RALLY50. I put a 25mm Spacer on it and it looks good. If it is longer than 25mm, it will be a problem to fix the screen, so 25mm is the limit.
The beautiful anodized black color of KITACO's aluminum spacer blends well with the black of the OEM front cowl stay of the CRF250RLY50.
View detail
The main point is that the outer diameter is larger than that of a regular collar.
I bought a battered 900SS (900SL) and am Restore.
The footpeg was made by Menani, but it was too battered, so we used parts from various manufacturers that we managed to put together to form the footpeg.
However, when I installed it, the footpeg mount on the frame side seems to be distorted only on the Right Side, and it slightly goes too far inside the vehicle body.
Left has about 5mm gap between footpeg and Swing Arm, but Right has only about 2mm...
As expected, it was too narrow, so we tried to optimize it by inserting a 3mm-thick Spacer between the footpeg and the Frame.
That is fine, but the contact area with the footpeg was small because the outer diameter of the spacer is a normal size.
I don't know what's wrong with that, but it bothered me, so I exchanged it for a Spacer with a larger outer diameter!
That is the product here.
The difference is slight.
However, those who laugh at it as slight are not qualified to talk about Tuning...so I feel good!
In fact, if you replace the Spacer only on the One Side, you will feel more like you are EXACTLY doing it.
I don't see anyone doing that.
The increased contact area should have increased the rigidity of the installation, but nothing can be felt.
Well, it's OK because it's self-satisfying.
The performance of Spacer itself is perfect.
Some hard Material (maybe in the 6000's based on machinability and Anodized's coloring? Mystery) and smooth surface.
0.It would be very nice to be able to purchase 1pc. units of Spacer for use on car bodies, unless there is a need for accuracy in 1mm increments!
View detail
To hide the hexagonal hole
Plating was peeling and falling apart, so the
Purchased to replace
It looks pretty shiny.
View detail
Good thickness that you can understand only when you put it on.
CUB90 with external Swing Arm.
I am adjusting the Rear to get the Line. Similarly, the Torque rod of the Rear brake also needs adjustment, so I purchased an aluminum spacer from KITACO.
Both length and thickness are as described. The chamfering is also well done, and the circumference of the aluminum cut-out is well made and beautifully finished. I like to look at something that is clean and good quality. This is just my feeling, but since it is used for the torque rod of the rear brake, I think this level of quality is fine. This time, due to the size, the quantity is limited.:2pc. Set purchased and connected to use.
I had to modify it a bit because the Spacer makes slight contact with the welded Sauce. We first measured and chose a spacer that could be installed, but it was not the right thickness. The measurement is a very small error, but it is a very large job.
It would be nice if all the parts could be diverted from Honda's OEM products, but it is difficult when other brand products are involved as in this case. KITACO offers many kinds of spacers, so it is very helpful. The size indication is written in Illustration on the back of the package. The Scale is also printed on the back of the package so that you can measure the parts you have. This is a very nice feature.
View detail
Copper Packing
I want to use copper packing for drain bolt when changing oil.
It was thinner and smaller than I expected.
There doesn't seem to be any oil leaks and the Seal is done, so that's good.
Quantity:1pc., cheap in terms of selling price? I wonder.
View detail
In Repair.
Installation was easy and problem free! View detail
Fantastic...
These small spacers are fantastic! The finish on the anodising and precision of the maching is perfect and they come in these wonderful little packages that are a joy to look at. They were great value too, compared to other options I looked at. Would highly recommend these if you are looking for spacers. View detail
Flashing installation
Purchased as a Spacer because the Blinker turns up
It might have been a safe win, but it turned out to be in front.
View detail
KITACO Needle SIMM set 3×6×0.3/0.6
Used to improve Kyanopi's mid-range speed.
I think it is good because it is cheap and effective.
View detail
Reflector should be attached.
I had a Fender Eliminator on my Axis Treat and cut the bracket that mounts the OEMReflector under the Number, so I stuck this product on the rear bracket part of the Pillion Bar of the Wills WIN.
The size is just right and the quality seems to be durable, unlike the ones sold in the 100s.
The double-sided tape provided with the product is a very strong adhesive, so it is best to position it firmly before attaching.
View detail
There are many different sizes.
You don't need impressions.
You will get Points, so please stay with us.
[How is it used?
Silencer BracketI just wanted to let it out a little.
Was the one you received as per Image?
And I've seen the actual thing at Image itself Naps.
Was the installation difficult?
It was so easy that I was surprised.
How was your experience with it?
That was great.
[Included Parts:were they on?
It came with an outer bag.
[Was there anything that disappointed you?
None at all.
View detail
Low Torque Location
Material:The aluminum anodized parts were about to be bald, so I inserted them between the parts.
It's just right to use it on Cowl for scratch protection.
It's a very solid object.
View detail