Reviews
GALE SPEED's Radipon's TankNipple's Angle conversion
The GALE SPEED radipon only comes with a TankNipple with Straight and no 90-degrees in Option, though,
for Rear with Angle can be fitted with this AngleNipple.
They are sold in the supplemental parts and can be ordered.
I wrote it here because I can't do imprints on ordered products.
Well, they are essentially the same thing, right?
The Snap ring can be installed, but the Rib part is slightly thinner than the Nipple for Front, so the Snap ring will rotate round and round if the Rib is left as it is. (No exclusions will be made) 。
I have not tried it, but it seems that substituting Nipple for Front for Rear is not possible.
If the O-ring is not old, it is Large sturdy, but you are on your own if you install it.
Hose is normal! Hose clamp is included. The inside diameter is not clear, but it is for brembo etc...
View detail
Stainless Steel anxiety and cleanliness are at odds with each other.
We decided to paint the hubs on the Yamaha car, and since we were going to do that, we also made new Disc Rotor Bolt.
Material:Although I was a little concerned about the strength of Stainless Steel, I couldn't help but be attracted by the fact that Stainless Steel is resistant to rust, and so I decided to purchase it.
In the past, I had heard that stainless steel has lower strength against shear stress than steel or Chromoly, so I avoided using it where large forces are applied perpendicular to the bolt.
The Disc Rotor Bolt and Caliper Mount Bolt are just that.
However, since KITACO has been selling this product for many years, we decided to use it this time because we thought it would not cause any problems and we do not have the skills to do Race or Hard Breaking.
I would like to check it regularly and see about durability.
View detail
Master cylinder cap screw
The master cylinder cap was silver and the same color as the Screw, so it was changed to a Black colored Screw.
Surprisingly, Screws in the same shape and Black color are not sold in stores.
It's a small detail, but I think it has improved Parenthesis by adding a sense of crispness.
It is a recommendation because it is very inexpensive and only requires the replacement of Screws.
View detail
Change from OEM
Change from OEMBolt
It will look better.
The accuracy of the hexagonal hole is not so good, so some tools may be damaged.
Beware of Overtorque.
View detail
Motorcycle is a large looking thing
Tightening the specified Torque27N?m makes the hex bite a little harder may also be sticky
If you can't afford Titanium but can't tolerate the rust, Recommends It is
View detail
It's cheaper than OEM Product ....
I was surprised to find out the price of OEM Product, I understood that this Stainless Steel is cheaper, I bought this ... ...
Hexagon's accuracy is very suspicious!
When prescribed Torque is applied, it seems that it does not eat firmly and a step mark remains.
It will be low accuracy & soft material.
This can not be reused.
View detail
Exchange is recommended in several times!
MONKEY's Bolt licked so I exchanged.
OEM (NSR50) SteelBolt is very soft,
By tightening with Torque prescribed, the part of Hexagonal becomes loose in several times.
But even if I used it without exchange, I had licked it perfectly.
For Stainless Steel I thought that Large would be tough,
It will become somewhat loose if you tighten with Torque prescribed about 3 times.
MONKEY (Diversion of NSR 50) When repairing Front such as Tire exchange and Pad exchange,
If you do not remove Rotor Caliper - Wheel can not be removed.
At the beginning Quantity : 1 Set of 4pcs. Although I bought it, since I ran out of it frequently when I customized it,
Daring 10 pcs. I bought a set.
Stainless Steel But because it is not hard,
Have some spares and early exchange is the Recommendation.
Three highs for material for less than expected + __.
View detail
[Webike Monitor] Since the attachment Bolt of the Rotor rusted and even the DISC was dirty, the product made from a Stainless was used at the time of reapplying a Wheel. although appearance is good, the hole of the hexagon head which inserts a to
[Webike Monitor] Since the attachment Bolt of the
Rotor rusted and even the DISC was dirty, the product made from a Stainless was used at the time of reapplying a Wheel.
although
appearance is good, the hole of the hexagon head which inserts a tool is pure -- since it is shallower, shortly after applying a Torque, a deep pool will rise.
It is better to prepare the
Torque wrench and a screw-thread Locke agent.
since specification for which
re-use is improper is carried out to the Package -- two or more times -- attaching -- removing -- special attention is required.
View detail
they are components indispensable to exchange of a brake hose! if it has hoarded -- if compelled -- it sometimes hurries and does!
they are components indispensable to exchange of a brake hose! if it has hoarded -- if compelled -- it sometimes hurries and does! View detail