Reviews
Manufacturer difference for Silencer
I bought this 95mm silencer spring because it seemed to fit to fix the Trickster Shotgun silencer to the exhaust pipe of my Wyvern ClassicR.
The length is perfect and the Spring is easy to install because one side has a Swivel hook and the other side turns. I have purchased a different size in the past, but the Material:It is a recommendation because Spring is made of Stainless Steel and has good durability. 。
Spring hook for installation (tool) It is easier to have a
View detail
Silencer can be fixed with Firmly!
The spring is so sturdy that it is difficult to extend it! View detail
Sturdy Spring.
I bought this because I needed a 65mm spring to join the Universal Silencer to the Tail Pipe.
I've used different Size before, but this is a very strong Spring and Recommendation! (^^)
View detail
Silencer spring
It was perfect.
If it breaks I'll buy another!
View detail
KITACOSilencer spring
I bought this in a hurry because the Spring that came in the kit was a Hook length that needed to be more than double that length.
It was fitting as if it was in the very Kit.
If I had wanted, it would have been perfect if it had an anti-vibration rubber.
If it breaks, I will buy it again.
View detail
Stainless Silencer spring
Silencer spring in Stainless Steel.
I also bought KITACO Anti-Vibration RubberCover at the same time. Quantity:Set and recommend to install it.
This product is a Material:It is Stainless Steel, so it won't rust like the cheaper Plating products that are often used. None.
In addition, because of its resistance to elongation and vibration, it can be used for vehicles with strong vibration such as single-cylinders. You can.
View detail
Stainless, so good texture!
The swivel hook type reduces the load on the spring considerably.
Material:It's Stainless Steel, so it won't rust even after long term use.
View detail
Replacement part
I exchanged because the rust of Spring of FMFSilencer is severe.
Although it is cheaper if it is not SUS, it is also a place where heat is applied and I chose SUS for rust prevention.
It's pretty hard so it's hard to install, but because SwivelType is somewhat easier to install.
View detail
Usage is different
I added Rear Sets and Brake's return spring ceased to be attached, so I tried it here.
The result was Large Satisfied! One Side stopped at footpeg, another side at Frame with Tie Wrap, and it was safe return spring.
Spring of Home center Spring Because the linear shape is thin and the attachment part is Vakka shape, I could not use it as a hook, so it was really nice to have a product like this one.
By the way, the mounting part of Tie Wrap is slightly bent, so it is different from the actual shape.
If used systematically, I use it other than Silencer spring. As Spring, it is hard to rust with stainless steel, and it is recommended because it is easy to process!
View detail
Spring with tightness
In order to raise the angle of the Exhaust System, since a Joint is put in it, a long Spring is required.
I used Spring outside the application, but it seems I've run out.
For commercially available Spring, it is best up to 120 mm?
Since 120 mm and 140 mm are necessary this time, Quantity 9x55 and 9x65 : I used 2pc each.
After all dedicated Spring has a different strength!
Tensile strength also increased, so it seems likely not to cut so much.
Also, Swivel hook is very easy to install.
View detail
Since he bought one trial and it suited well in order to attach the Exhaust pipe and Silencer which were bought with the Webike Monitor auction, he bought it with one addition this time. Since the place which can scratch attachment rotates freely,
Since he bought one trial and it suited well in order to attach the Exhaust pipe and Silencer which were bought with the Webike Monitor
auction, he bought it with one addition this time.
Since the place which can scratch
attachment rotates freely, it is convenient.
Since it was a Silencer whose Manufacturer is different this time, and an Exhaust pipe, it was made to rotate 90 degrees and attached.
Since there was a just right Size, it was good.
View detail
a Size -- made in [ STAINLESS-STEEL ] Toyotomi -- the worries nothing of rust -- and it is cheap. It is perfect.
a Size -- made in [ STAINLESS-STEEL ] Toyotomi -- the worries nothing of rust -- and it is cheap. It is perfect. View detail
It is 95 mm of free length, the recommendation attachment length of 99 - 105 mm, a diameter of a spring of 9 mm, and entering one piece. I think that it is hard to rust since construction material is a stainless. Since one side is a swivel hook, a
It is 95 mm of free length, the recommendation attachment length of 99 - 105 mm, a diameter of a spring of 9 mm, and entering one piece.
I think that it is hard to rust since construction material is a stainless.
Since one side is a swivel hook, a favorite angle can be rotated and it can attach.
View detail
It was used for repair of the collecting pipe of the moriwaki of HONDA X-4. A feeling of attachment and a wearing feeling are good touch. the spring which became old goes by little power with POKITSU, and meets by it -- coming out -- after - also
It was used for repair of the collecting pipe of the moriwaki of HONDA X-4.
A feeling of attachment and a wearing feeling are good touch.
the spring which became old goes by little power with POKITSU, and meets by it -- coming out -- after - also rusting -- since it was severe, it exchanged for the new article.
Although it is troublesome, since it can exchange freely and a feeling of adhesion is also raised, it is recommended by all means.
View detail