Reviews
For carbon silencer.
To Maverick's MV83Carbon silencer.
The Maverick Exhaust Band is a common silver color, so I thought it would be more consistent if I changed it to black. I changed it to black to make it look more consistent.
The color and Size matched.
The Bolt hole in the band section is narrow between the Bolt hole and the Exhaust System, so it might be a little bit higher.
The bolt nut that came with the product was too small to use, so the OEM product was reused.
View detail
It's beautifully made.
I purchased this for my Yamaha SEROW which has a round external Silencer installed.
I made my own back guard to be attached to the silencer to protect the back for long touring. I have been using this product for a long touring, but I have to replace my round silencer band with an oval silencer band because the stainless steel is very hard and it is difficult to use it for other shapes. In my experience, it takes a long time to bend stainless steel by hand or to form it into an oval shape, and the result is not good. Unfortunately, the round Silencer band has been put into temporary storage.
The product itself is fine and well made; it is made of 1mm Stainless steel flat plate machined to 110 pie inside diameter. The bracket is raised vertically from the circular shape and is hammered to hold a right angle. The cap bolt is 25mm long, 7.7mm in diameter, and only needs an 8mm mounting hole. The Elastic band is not just a black flat rubber band, but is made with a horizontal gap to prevent it from moving. The bottom of the engraved Bracket is clearly marked 110 Pi. This kind of workmanship is very helpful when you own several similar parts.
It is relatively easy to make round-shaped bands made of gold where there are machine tools, and other manufacturers also offer a variety of bands. KITACO is a good company that sells at a cost like ConveniencePartsSeries.
View detail
For carbon silencer
I had heard that it was difficult to find the right size, but I can fix it to Maverick's Silencer without any problem.
Recommended for those who want to Blackout.
View detail
Silencer band
I used this product to fix the arrow silencer, as the OEM silencer is fixed directly with the bracket, but I was concerned about scratching and heat transfer to the car body. I used this product because I was concerned that it might scratch or transfer heat to the car body. It was very easy to install. View detail
Silencer band
I was a little concerned about the lack of band on the arrow silencer, but now I can relax. View detail
That's KITACO. Cheap!
I bought a silencer band from KITACO because I changed from Earls Gear's silencerφ100 to Universal Product's silencerφ80.:It looks very beautiful and sturdy with Stainless Steel, but I had trouble fixing it because the diameter of the silencer is 1cm lower than the original one. I would be happy if there was a type that could adjust the length of the mounting part as well as the type of φ, but I guess it would be difficult considering the cost. (Especially, it is difficult to extend the length by 1 to 2 cm because you cannot put a bracket between them.) The silencer was too large, and when I put in the rubber sheet, the phi; became a little too small to reach, and I put in the 6mm spacer and installed it. By the way, Material:Although Aluminum is availableMaterial:Titanium is expensive and unprofitable, isn't it? If possible, is it possible to get a one-off price at Netetc.?
It is very helpful to have a manufacturer like KITACO who provides various universal products and parts at a good price.
Please keep up the good work. I'm rooting for you.
View detail
Recommendation to Carbon silencer!
I purchased this product for Maverick's for Carbon Silencer. This product is inconspicuous Black Spec. so it blends in with Carbon Silencer, so it is Recommendation.
The carbon silencer is not conspicuous if it is silver, but this is a recommendation.
View detail
Replace OEM is too expensive, so it excels as a Universal Product
It's just a Silencer band, but there is no problem with the texture and rubber quality
You will need to adjust the top of the head as the attachment point comes to the Center
It's a Stainless Steel plate, so you can get away with bending it back
The design is not bad and it is a very useful part for Repair
As for durability, the rubber cracks and discoloration does not occur, and the BracketBody does not crack
Necessary and sufficient
It is used for the outside 100 φ Silencer (TSUKIGI) of HORNET250
The price is so cheap and the size is so modest that it is very reliable for the poor!
View detail
A well-built product
Vino (SA10J) I used it to
The exhaust system of N company is installed The exhaust system of Silencer fixed by aging
The Rivet was loose and I used the Hand Riveter to re-hit it
I'm worried about it, so I bought a Silencer band to fix it to the body of the car
The Silencer band and bracket for the body are made by the T Company
Put it between the Silencer and the attached HexagonalBolt&Nut
It's only 13mm, but Nut is 13mm, so you need to be careful about the tool you use
This is where you want them to use the 14mm Nut that is commonly used for Motorcycles
Align the Bracket with the HexagonalBolt and tighten up the HexagonalBolt to avoid wobble
Firmly fixed
The construction of the bending part is very solid, and the Material:Stainless Steel, so it will rust
It's good to have no worries
I like it because it has excellent cost performance at a reasonable price
View detail
It is said that there are parties saying - - -.
Rubber of the Silencer band cracked and it became terrible.
I did not think there was any Repair Parts, but I was surprised to see it on Webike!
It is a certain thing.
Size was measured, so it does not change at all from what I was with. Durability will be verified in the future.
However, I feel Length is incomplete.
In my case, because it was a Twin silencer Quantity : It was necessary for 2pc, but 1 pc was not enough for Cover eventually the same thing as Quantity : I bought 2pc.
View detail
I was in trouble as Aluminum Band broke
If you use KIJIMA 's AluminumBand, it will be packed up in about a month
So I was in trouble and made this.
In Stainless Steel it was inexpensive that the deciding factor of purchase.
The thing is also the wall thickness (At least from Aluminum) It is robust..
It will not break.
Just remove the Rubber board and set it up with Aluminum silencer and galvanize and Silencer side
It became textured. If it is Stainless Steel it can be as it is,
If the other party is a heterogeneous Gold genus, it is better to use the attached Rubber board without fail.
View detail
[a Webike Monitor] -- good considering the price -- it is making and carrying out. The Size is also abundant and it has satisfied it very much. It is ! so that a hand may not be cut, since there is a Band [ itself ] BALI.
[a Webike Monitor] -- good considering the
price -- it is making and carrying out.
The
Size is also abundant and it has satisfied it very much.
It is ! so that a hand may not be cut, since there is a
Band [ itself ] BALI.
View detail
Since the external Muffler without a Band was obtained, he bought it. Considering a price, a Band and a Rubber have good structure, and appearance is not so good with the Band of external Muffler attachment at it, either.
Since the external Muffler without a Band was obtained, he bought it. Considering a price, a Band and a Rubber have good structure, and appearance is not so good with the Band of external Muffler attachment at it, either. View detail
Since it fell and lost while the rubber attached to the muffler by attachment ran, this product was purchased. Since return sticks, it is fixable to a band firmly. I think whether since the die length is 50 cm, it suits most bands.
Since it fell and lost while the rubber attached to the muffler by attachment ran, this product was purchased.
Since return sticks, it is fixable to a band firmly.
I think whether since the die length is 50 cm, it suits most bands.
View detail