Reviews
![[K-CON Pro] License Plate Base](https://img.webike-cdn.net/catalogue/images/69385/0901-657-00050b0_TS.jpg)
License Plate Base
License Plate was installed to prevent bending and staining.
The size is exactly the same as the License Plate, so it fits nicely.
I would have liked it to be a little lighter in weight.
View detail
Convenient to make it the same color as OEMHarness.
It is convenient to unify the Minus power supply system and Earth system of the retrofit attachments with the Earth system of Kawasaki OEM Harness, Black/Yellow. View detail
Convenient to match the Wiring color of OEMHarness.
It would be helpful to be able to make the color of WhiteHarness, which is equivalent to the Batch+ after the KawasakiOEMHarness junction box, and the Batch+ of the retrofit Attachment, the same White. View detail
It is usable enough. Soft but not tight enough to lick.
It is often written that the six corners become rounded, but when I tightened them with the torque wrench by pressing the tool firmly, the corners were indeed slightly deformed, but not to the extent that they became impossible to tighten.
If you say you can't install it, it's probably because of poor workmanship.
If you discount it as a cheap product, it's not bad at all.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
A friend of old cars?
I'm not sure about current vehicles, but this is a common two-turn Bullet Type Terminal on older vehicles.
I get the impression that there are a lot of them, especially around Tail.
View detail
For additional Wiring
I found an article that the Bullet Type Terminal for Motorcycle is slightly different in size, and it seems that it is not Exactly fitted to A0 products, so I bought one to try it out.
I do think it's harder to pull off than A0.
Why would they change the Size?
And I didn't know there was a difference even among MotorcycleManufacturers.
It's an essential component for safe Wiring processing.
View detail
for adjustment
Repurchased to add a step on the Screen I had previously put on. View detail
Easy to use
I bought it because I couldn't find it at my favorite store and there was just a Point.
It is easy to use, but the rubber rubber doesn't last long because it is used in a place where it is bent many times.
We purchased several in stock as consumables.
View detail
It can be used normally
The female side of the Harness was too stiff, so I used this product to change it. If you tighten it too hard, the cable will break and the connector will become useless, as is the case with other connectors. View detail
Ideal for blowby gas extraction
The basic application is as shown in the Title. However, it is too thin to be used for cars and motorcycles with high engine displacement volume, which may result in poor performance and malfunctions.
The durability of the paint is unknown, so it was rated 3 Stars.
View detail
I am satisfied with this price.
GCraft's CarbonPerafen is a surface [Color] I bought it to distribute the pressure with a thin Spacer with a Large tight outer diameter because it looked like it would crack with the Bolt that came with something like Clear.
The Spacer in this Series is finely Sized, which is helpful.
View detail
A wide variety of size variations to choose from
Multiple patterns of OD, ID, and thickness are available for use in various places.
This time Webike had M10Size in stock and I was planning to purchase other products, so I bought it as well.
Size, texture, etc. are perfect.
It was a great help because it was a hassle to go all the way to the Motorcycle supply store to buy the Size, which was not available at the nearby Home center.
It is not worth the hassle and cost to select and buy each Size, so if I wanted, I would have to pay 3,000 yen for a Quantity that contains multiple items and is less expensive.:I wish I had a Set product.
View detail
Good to keep it from loosening
I purchased this product for Exhaust System fixed Bolt.
The lock is tight and will not loosen, so it can be used safely in any location where there is vibration.
View detail
Instead of Washer
It was used as a Spacer when installing GIVI's Carrier.
I usually use a 6mm washer on top of a 6mm washer because it is a hassle to measure the size and prepare a spacer, but since I drop it every time I do maintenance, I replaced it with this product to improve serviceability.
It's just an ordinary Spacer, but it's nice to be able to choose from several sizes and thicknesses, etc.
From a functional standpoint, stacking Washers is sufficient, but this is a good product for those who care about appearance and serviceability.
View detail
Thank you for all your help.
I use it all the time.
Thank you again for your assistance.
Sometimes the stock is low at nearby mass retailers, etc., so Webike helps me out in such cases.
View detail
Instead of Indicator's Window shade
[How is it used?
PlugWindow shade on YAMAHA XJR400R Indicator? (OEM number:16G-13569-00) Because of the AISCancellation, I had to blind the place where the hose was originally attached, so I used this instead.
How was your experience with it?
The size was a little short in height and the inside diameter was not quite right and a little loose.
The Clip on the Horse was used to prevent it from coming off while driving.
How did it compare to other products?
I finally repurchased the OEM because I was afraid of sucking secondary air due to the thinner Rubber and slightly looser inner diameter compared to the OEM number:16G-13569-00. However, I had no problem using it as a substitute.
[Points to note]
The inner diameter is loose and must be stopped with a Clip or inHemp palmock.
View detail
Used as Spacer for Exhaust System
When I buy a used external exhaust system, it may not have the spacer or bolt I need, so I buy it when I need it. It is very helpful that there are various sizes. View detail
Used for adjusting the width of Handlebar.
[How is it used?
The XJR1300C, which had to be inspected, was missing a handlebar width of about 10 cm, so we used four of these collars to pass the inspection.
The idea came from the Handlebar Spacer for the Z900RS from ARCHI.
Was the one you received as per Image?
It was just the right thickness, I wanted more than 22.2mm.
How was your experience with it?
Quantity:Pair (for Left and Right) To Quantity:2pc. Set by Set, and finally fixed at the Bar End of Babyface.
The inspector did not point out any particular problem, and the vehicle passed without incident with the width as stated on the inspection certificate.
View detail