Reviews
I don't know if it will fit, but I bought it anyway.
I don't know if it will fit, but I bought it anyway. View detail
GALE SPEED's Radipon's TankNipple's Angle conversion
The GALE SPEED radipon only comes with a TankNipple with Straight and no 90-degrees in Option, though,
for Rear with Angle can be fitted with this AngleNipple.
They are sold in the supplemental parts and can be ordered.
I wrote it here because I can't do imprints on ordered products.
Well, they are essentially the same thing, right?
The Snap ring can be installed, but the Rib part is slightly thinner than the Nipple for Front, so the Snap ring will rotate round and round if the Rib is left as it is. (No exclusions will be made) 。
I have not tried it, but it seems that substituting Nipple for Front for Rear is not possible.
If the O-ring is not old, it is Large sturdy, but you are on your own if you install it.
Hose is normal! Hose clamp is included. The inside diameter is not clear, but it is for brembo etc...
View detail
Copper Packing
I want to use copper packing for drain bolt when changing oil.
It was thinner and smaller than I expected.
There doesn't seem to be any oil leaks and the Seal is done, so that's good.
Quantity:1pc., cheap in terms of selling price? I wonder.
View detail
I like the stuff, but I didn't need it for crf250rally….
Purchased when replacing crf250rallyBlinker
Rear blinkerMinus side connector is not the same shape as the light blue or Orange one, so I thought I could use it on the Plus side,
The Minus side is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
I wanted a Stopper in the middle.
I used it on a Gasoline sub tank, it's useful for connecting hoses together, but it's a bit unreliable plastic, so you don't want to use pliers or anything like that when installing it.
A stopper in the middle would have made it easier to use. I'd rather have an aluminum one or something.
View detail
Wire Fixing
It is 1m short for wiring. This time I bought it for fixing to suppress wobble of change shift which is a chronic disease of GB250 CLUBMAN. 0.57mm is just right and 0.6mm is not enough to fit in the gap of change shift, so I could not wrap it. I am worried that it will break, but it is a first aid measure, so I would like to see how it goes. View detail
exchange
The connection connector of the main power supply was old, and its removal and installation was strange.
TAB, receptacle, and Terminal Set, so it is much easier to remove and install with the new replacement.
View detail
For UniversalMeter installation
In replacing the Meter with KOSO's Multimeter, we did not want to damage the harness on the body side, so we purchased a 110-type 9-pole and 3-pole Coupler and made an intermediate harness so that the new Meter could be detached with the Coupler.
The product was a perfect fit, the terminals were solid, and the product was safe to use. The coupler is compatible with the coupler attached to the harness on the body side of the car without any problem, and it can be attached and detached smoothly.
I think it was a bit of a waste since I only used One Side, but I will keep the extra one in a Large Cutout until I need it some other time.
View detail
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Stainless Steel anxiety and cleanliness are at odds with each other.
We decided to paint the hubs on the Yamaha car, and since we were going to do that, we also made new Disc Rotor Bolt.
Material:Although I was a little concerned about the strength of Stainless Steel, I couldn't help but be attracted by the fact that Stainless Steel is resistant to rust, and so I decided to purchase it.
In the past, I had heard that stainless steel has lower strength against shear stress than steel or Chromoly, so I avoided using it where large forces are applied perpendicular to the bolt.
The Disc Rotor Bolt and Caliper Mount Bolt are just that.
However, since KITACO has been selling this product for many years, we decided to use it this time because we thought it would not cause any problems and we do not have the skills to do Race or Hard Breaking.
I would like to check it regularly and see about durability.
View detail
Used to reduce rattling of Brake lever
[How is it used?
Brake lever was rattling badly and I bought it in hopes that it would get better.
The Touch feeling of the MASTER itself was not so good, but I suspected that maybe it was because the rattling was so bad that I could not press the Piston straight? I also suspected that it might be because I could not press the Piston straight.
To be honest, since it is a SmallEngine Displacement Volume for a foreign car, I thought that the rattling might be terrible combined with poor accuracy, but I tried it when I learned from an article on Webig that this Washer can reduce the rattling.
Was the one you received as per Image?
As you can see in the picture, it is just a Washer.
It is not a very expensive product, but the price of this thin Washer may be too expensive for some people...
Was the installation difficult?
Simply remove the Brake lever and insert it in between.
Washer is just on Lever, so it is a bit frustrating to have to Gap it back to MASTER.
How was your experience with it?
Actually, I first tried 0.3mm, but did not feel much change. 0.6mm with 2 layers of 0.3mm reduced rattling in a good way. However, I felt that the movement of Lever was a little reluctant or stuck, perhaps due to the two layers of 0.3mm, and I felt it was dangerous.:I settled on 1pc. Even with 0.5mm, there is some rattling, but it has been reduced to an acceptable level.
However, I did not see any large change in the touch feeling that I had expected, and I felt again that in such a case, I had no choice but to replace the entire MASTER.
[Included Parts:were they on?
Washer only.
[Was there anything that disappointed you?
nothing special
View detail
Bolt cover
Bolt, installed for protection purpose to the Nut.
It seems to be a little hard plastic and is hard to remove after installation.
Quantity:1 Set of 3pcs., the price is not that much and it will look a little better.
View detail
ScrewCover
The screws near the Exhaust System interfere with vibrations and cause scratches, so I bought this to try to protect and prevent scratches.
The colors are vibrant, not bad looking.
Quantity:1 Set of 3pcs., the installation seems to be a little stiff and difficult to remove.
View detail
2 while shopping
It's just self-satisfaction. I don't care if I don't have it.
It is a Dress-up that only those who ride the same Motorcycle will notice.
But isn't it good!
View detail
World's Strongest Loosening Washer
I bought this one after mistakenly buying a Nut with a locking nut without a locking nut, and was thinking of replacing it with a Spring Seat Gold or Nylon locking nut, but they deteriorate and can only be reused about 5 times. I was thinking of replacing them with Gold or Nylon type Nut, but they deteriorate and can be reused only about 5 times. I tried it because it seems to be reusable.
Nord-lock washer:The world's first friction-independent, non-loosening product is the non-loosening Washer developed by Nord-Lock."
The "WedgeLocking effect" caused by Cam makes it physically impossible for Bolt to spontaneously return and rotate to loosen. according to what someone said Physically impossible." That's a great thing, isn't it?
Check the bolt length and clearance something.
Run it and it doesn't loose at all. It's awesome.
View detail
For fixing Silencer
Purchased for use in the Band section for fixing Silencer.
It seems to be good for vibration and scratch protection. The price is not that high, so I hope it has some Rubber durability.
The product is not that expensive, but the cut ends are slanted, and I had to cut them a little to use them. I would like to see the product sold with a straight cut.
View detail
Shipping Adjustment
Purchased to adjust price for free shipping.
Unlike ordinary Tie Wrap, this is a Release type, so it has the advantage of being easily reusable, and we plan to use it for harnesses around lights that are moved a little more frequently.
Quantity:1 Set of 2pcs. so I don't think it is cosmetic. I don't think there is any Merit to buy except for price adjustment.
View detail
To M8 with M10 color
I wanted to use the Exclusive Aluminum Spacer for M10 Screw Collar from the same K-CONBrand with M8 Bolt.
These itchy parts are very helpful.
Surprisingly, there are no conversion parts like this.
View detail
Can be inserted into a hole and fixed in place.
It is a product that can be inserted into the hole and fixed with Tie Wrap.
Thank goodness I usually don't sell Rose.
View detail
PetitCustom
PetitCustom Bolt Hole Cover for Handlebar Clamp. View detail