Reviews
Fits: SUZUKI GSX-S750, SUZUKI SV650 ABS, SUZUKI SV650X ABS
It doesn't feel any different from OEMLever.
[How is it used?
Application is replacement of OEM Clutch Lever.
Was the one you received as per Image?
The size is almost the same as OEMLever, and it has a good texture without looking uncomfortable.
I like the fact that you can see that the design has been changed casually, not in a way that says Lever has been changed.
Was the installation difficult?
It's not difficult to remove and install, but be careful not to break the switch (convex part) of the clutch attachment.
How was your experience with it?
The operation feeling is the same as OEMLever. (I haven't touched the Lever position adjustment, but it is almost the same as OEM)
[Included Parts:were they on?
None
[Was there anything that disappointed you?
To adjust the Lever position, you need to turn the Adjusting bolt, so you need a tool to re-adjust it on the go.
However, since it is difficult to be misled rather than being disappointed, I try to think that this is possible.
Installation can be carried out by one person with the appropriate tools, without any special skills or support required.
Instruction Manual is attached, but it is too small to read. (The replacement itself can be done without the Instruction Manual.
Replacements are Brake lever and Quantity:In the event of a fall, Foldable is a lever.
In addition, the lever position adjustment itself is not possible with the OEM lever, so it was good to replace it.
It is
View detail
Fits: KAWASAKI ZX-4RR, KAWASAKI ZX-25R SE, KAWASAKI ZX-25R, KAWASAKI Z650RS
To divert the bremboLever
With the replacement of the Master Cylinder of ZX-25R, I wanted to have the Clutch lever also, but it cost about 40,000 yen if I get it from 0OHKEN.
I bought it at the last minute because the shape was the closest to what I was looking for, and it turned out to be a success.
I was not able to attach it as it was, but by shaving a few millimeters off the end face of the Comma, I was able to attach it. Miraculously, the bolt diameter and length all matched and no additional parts were needed.
I was also worried about the interference caused by the difference in Lever shape, it touches the Switch box slightly, but not enough to damage it, and if you raise the Lever height, it will not contact.
The diversion lever is a RCS HalfShort, I prefer to use two straps, but the length is about three straps.
As for the performance of the holder itself, I did not feel any change in the lightness of the rattle or pull.
I bought a set in relation to the delivery date, but I think that the person of the diversion purpose is good there because there is sale in Holder Only.
View detail
Fits: KAWASAKI ZX-14R, KAWASAKI ZZR1400, KAWASAKI 1400GTR, KAWASAKI ZX-14R
Replace to match Brake lever
[How is it used?
In use. About three years have passed since it was installed.
Was the one you received as per Image?
As per Image. It is good that the adjustment Dial position is not as shown in the product image.
Was the installation difficult?
With Nisshin's MASTER, you only need to replace the Lever, so it's easy.
How was your experience with it?
The first thing that bothered me was the feel of Lever, but I felt uncomfortable because it had more corners than OEM, but I got used to it while using it.
The dial adjustment allows you to adjust the position in detail, so it is convenient to adjust the position easily and finely when the Glove is changed or the Clutch is not cutting well due to lack of maintenance.
Even if you fall, if it's Foldable, you can avoid breaking the Lever and making it inoperable.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
At the time of replacement, cleaning and grease application is Large thing.
Adjustment Dial has a feeling of high quality if there is a feeling of Click as much as brembo, and I want you to improve it.
View detail
Fits: HONDA CB400SF, HONDA MONKEY125, HONDA CB400SF, HONDA MONKEY125, HONDA CB400SB, HONDA CB500, HONDA CB400SB, HONDA GROM, HONDA CB125R, HONDA CBR250R, HONDA CB250F, HONDA CBR250R, HONDA CB250F
Active stf clutch lever
The clutch lever looks was very nice. The build feel solid. Installing the clutch lever is easy. But there's one thing I feel down at the end of the lever there's a hole.. That cut out is sharp when I want to clutch in and really feel discomfort. Because I clutch in using 4 fingers. For the brake lever that cut hole not sharp at all. View detail
Fits: YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09 TRACER, YAMAHA TRACER900, YAMAHA XSR700, YAMAHA MT-07, YAMAHA MT-07, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA MT-09, YAMAHA YZF-R7
The operability is now outstanding.
I'm using this on a 2018 Toracer 900.The OEMLever is a pretty Large sketchy build and hard to grip for us, so I changed it. It has a wide adjustment range and is easy to operate with two fingers, making it as easy to handle as a mid-sized Motocross. By the way, we are 80kg grip strength. View detail
Expensive.
Expensive, but the texture is very good, just like the ZETA I always use.
KawasakiOEM is useful because there are only 4 adjustment steps.
The installation accuracy is also high.
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Good texture and good touch.
I changed the brake side to GALE SPEED Radial master and the color is Black, so I bought the same Black one for the Clutch Side.
They are both Active products, so they look the same except for Small Logos.
Wobble that was on the OEM is also reduced and easy to operate.
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Good!
I had the installation done by DREAM. It is easy to grip and does not break even if it falls. However, because the inner Bolt hits Grip when you grip it, it leaves a small mark. In the first place, if you just grip it normally, you don't grip it until it hits you so much, so it is just a matter of whether you care about it or not. View detail
Fits: YAMAHA YZF-R7, YAMAHA YZF-R1, YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-07, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA MT-09, YAMAHA TRACER900
Not compatible with MT-10
In this site, both MT-10 and MT-10SP are adapted, but they are not
The Holder needs considerable processing It's a lot of cutting
First of all, the protrusion to push the Clutch switch hits the bottom of the holder
I shaved that place, but the Bolt hole doesn't fit, and if you look closely, you can see that the line on the lower side of the Holder delicately is not correct
I can't get the Bolt to go through the installation because of that
Furthermore, the length of the screw is not long enough to adjust with the Adjuster on MT-10, so it is almost impossible to adjust it Mm
I bought it believing it would fit, and then crunched it up because the installation didn't work
I didn't want to have to deal with the return of the product, so I went with the Holder process..
Active's website doesn't mention MT-10, so..
Why does Webike fit in? I'm not sure why you would say that
I feel cheated
Mr. Webike
I think it would be better to remove the MT-10 compliance notation
I don't want there to be any more victims like me..
View detail
Fits: HONDA CB400SF, HONDA MONKEY125, HONDA CB400SF, HONDA MONKEY125, HONDA CB400SB, HONDA CB500, HONDA CB400SB, HONDA GROM, HONDA CB125R, HONDA CBR250R, HONDA CB250F, HONDA CBR250R, HONDA CB250F
Is good
It was installed at the same time as the Active's STFBrake lever It is slightly more angular than the OEMLever, so it is easy to get a finger on it The adjustment mechanism is a screw driver, so you can't adjust it without a tool It would have been great if it had the same adjustment mechanism as the brake lever on the MONKEY125 It was a shame that the rubber cover hides the logo on top of Lever when it is installed View detail
Fits: KAWASAKI Ninja250SL, KAWASAKI NINJA250, KAWASAKI NINJA250, KAWASAKI NINJA400
There is no Instruction Manual
The quality of the product is good, but
There is no Instruction Manual etc
Installation Clearance is also quite tight, so it took a lot of work to install it
How to adjust the position of the Lever since there is no instruction manual at all I didn't know how to adjust it
As a result of adjusting with the play of Cable, Shift became hard and Clutch slipped
Isn't it common sense to keep an Instruction Manual on a piece of paper?
I think the quality is good, but as a product it sucks
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Fit feeling to the finger and ease of adjustment are excellent
I attached it to MT-09.
I used the Short Type of the company's Billet clutch lever, but since I felt that my hand was Large or not, I felt that the operability was bad, so I bought an item of STD Type this time.
【What made you decide the purchase?】
Until then I was wearing the Short Type of Billet clutch lever made by the company and I already knew the feeling of Fit to the finger and ease of adjustment, so STD Type things that will be handed Fit this time I nominated you.
【How was it actually used?】
Although I already knew the feeling of Fit to the finger and the ease of adjustment, I felt that the operability was better than that by exchanging with Lever of STD Type.
Also, my MT-09 is equipped with Bar end mirror, but there is no interference with the Bar end mirror that I was worried about, so it seems to be safe to use.
【Mounting was difficult?】
For example, I think that it is possible for anyone to exchange as long as the experience of twinkling the Brake relationship of the bicycle and the appropriate tools are available.
As recently as YouTube says Leveretc. There are people who are upgrading exchange videos, so I think that it is no mistake to refer to such things.
【Please tell me the installation point and hang】
Please do not forget to wipe old Grease of Pivot part & apply new Grease.
[Is there anything I was disappointed about?]
None
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it was still better if Bolt of the fallen part was black thing.
【Have you compared items?】
This time I was nominated to buy Short lever from Change, but the items compared before purchasing Short lever will be below.
- DAYTONA Aluminum Cut Out Adjustable Clutch Lever
Since the Red part of Adjuster judged to my Motorcycle, it was removed from the candidate.
[Others]
I think that it is good to choose the STD Type without hesitating to the big Large person of hands.
If you forcibly make it a Short Type, it will become a way of entering strange power, especially when you ride a long distance, the way you get tired is different.
View detail
Fits: HONDA CB1100, HONDA CB1100EX, HONDA CB1300SB, HONDA CB1300SF, HONDA CBR1000RR, HONDA VFR800, HONDA X-4, HONDA X-4 LD, HONDA CB1100RS, HONDA CB1300SF, HONDA CB1300ST
Billet clutch lever
Because I replaced Brake with Brembo master, I exchanged the color of Lever to unify it with Black. Design and features are also great.
It's perfect if the price is a bit cheaper
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Bar end mirror Short Type was chosen for interference
As in Title, in the Type with the same Length as OEM or OEM, we selected Short Type to interfere with Bar end mirror.
【What made you decide the purchase?】
We chose this product because the price is also cheaper compared to other companies' products and because it is a Brand's name that passed well, I think that quality is no doubt. Also wasteful decorations commonly found in other companies' products (Adjuster coloring etc. etc. ) There is not, and it is likable that it looks refreshed in Simple is likable..
【How was it actually used?】
Obviously, interference with the Bar end mirror which was the original purpose was avoided.
Immediately after the exchange from OEMLever, I became Short, so I was a bit puzzled, but as soon as I had a few hours I got used to it. Now I'm also going out for a long distance Touring that is more than 500 kilometers a day.
It also seems that the touch of the finger is also good and the operability has increased.
【Mounting was difficult?】
Since it is almost the same as Oever Lever, if you refer to the service manual of the car body, I think that it is possible for amateurs to install without problems.
【Please tell me the installation point and hang】
I had never tried replacing Lever or anything else, I was a completely amateur, but I could exchange it easily by referring to the service manual and the blog of MT - 09 Owner and following it. Although it is possible to replace even with a tool of 100 Level level, it is better to use a good tool with high accuracy if possible.
[Is there anything I was disappointed about?]
There are no particular discontent points.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it was better if there was a middle size between Size and Short.
For example, 2 Finger, 2 like Brake lever of SportsCycle, 2. If you have a Lineup of fine Length like 5 Finger, 3 Finger, I wonder if Cover could be widely covered in various hands.
【Have you compared items?】
DAYTONA Aluminum Cut Out Adjustable Clutch Lever
As far as the photo is concerned, the fundamental part is Silver, because Adjuster part is Red, I decided that it does not fit my Motorcycle and removed it from the candidates.
[Others]
Because it is Foldable, it is also good to reduce the possibility of inability to run due to breakage of the Clutch lever by any chance.
Moreover, I will try to purchase Repeat once it is deteriorated or damaged.
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
* The shown image is only for reference. It may differ from the actual product.
Since I used it before, I exchanged it. * The shown image is only for reference. It may differ from the actual product. So Lever is a Fixed Type so please do not mistake it. If you want Lever's Adjuster please choose another Manufacturer. View detail
Fits: KAWASAKI ZZR1400, KAWASAKI 1400GTR, KAWASAKI ZX-14R
By exchange of the Lever, a Clutch came to go out certainly and it became light.When in play was read, the dissatisfaction about finish of an angle part stands out, and although it was worried, I who grasp a Lever with four fingers did not necessarily hav
By exchange of the Lever, a Clutch came to go out certainly and it became light.When in play was read, the dissatisfaction about finish of an angle part stands out, and although it was worried, I who grasp a Lever with four fingers did not necessarily have a pain in a finger in an angle part, when inserting in the Glove.However, it is wonderful in why it is not made although what is necessary is just to only carry out the same finishing as a Brake lever.Even a star is a decrease about that I want you to make the
price a little cheaper and finishing.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI 1400GTR, KAWASAKI ZX-14R
It was as expected mostly. When it fell with a pure Lever before , there are the circumstances where the Lever was folded and it made it the retractable type. -- Although in play is not made since the fall has not been carried out yet ...
It was as expected mostly.
When it fell with a pure Lever before
, there are the circumstances where the Lever was folded and it made it the
retractable type.
-- Although in play is not made since the fall has not been carried out yet ...
-- one regrettable merely uniquely had changed, although [ with a cheap Adjuster ] it was round.
It was regrettable to that which making
says.
View detail
Since the brake lever broke with the fall this time, he bought repair. Since it was the die length of normal last time, he bought a short this time. Certainly [ comment become in ... and ]!! Since it grasped the inner side when it was normal, sinc
Since the brake lever broke with the fall this time, he bought repair.
Since it was the die length of normal last time, he bought a short this time.
Certainly [ comment become in ... and ]!! Since it grasped the inner side when it was normal, since the brake was always grasped by an index finger and the middle finger, for a while, it was hard to put in power and it felt it.
Since it is exactly after changing into a short, it comes to be able to perform former more fine operation, and becomes easy to grasp it.
Since it is repair, a place changeable at a low price is also good.
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Since the brake lever was before folded by the fall, it exchanged for this lever, but since there was a difference in the appearance of a lever on either side, it purchases by appearance serious consideration. Although an authentic positive one is the
Since the brake lever was before folded by the fall, it exchanged for this lever, but since there was a difference in the appearance of a lever on either side, it purchases by appearance serious consideration.
Although an authentic positive one is the roundish form, and I am individually disagreeable, since it is horned here, it is to its liking as me.
View detail