Reviews
Large Satisfied
Since the oil cooler for Harley-Davidson does not have a horizontal type mount type, we fabricated a mounting bracket and installed this oil cooler. The oil cooler was installed on the front frame in front of the engine through the aforementioned bracket so as not to interfere with the front fork and not to obstruct the foot space. It was installed quite nicely. View detail
![[Repair Parts for Big Radiator] Universal Radiator Core Body](https://img.webike-cdn.net/catalogue/10955/5050003_TS.jpg)
Fits: KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200, YAMAHA V-MAX
Careful
Big radiator kit was already installed, but this time I purchased only Core for water leakage from Radiator, but … It seems that the Model change was done in the direction of Mr. Active, the fan bracket and Core guard were also changed in size. It was. I should have purchased it with Kit from the beginning, Camouflage…I have no complaints about the product itself, but.... View detail
ActiveTubing separator
We are very pleased to have purchased the ActiveTubing separator.
I installed the product as soon as it arrived.
Installation was easy and Fitting was perfect.
I would like to use it again.
View detail
To Active's Wire.
I used it on Active's Accelerator Wire. It is a little Large compared to other Manufacturers, so it binds FirmlyWire. I recommend this product because it is beautifully made. The price is reasonable. View detail
ประกัยยึดสายได้อย่างพอดีสวยงาม View detail
Exclusive, good quality, but too expensive...
[How is it used?
I installed ACTIVEStraightOil cooler 10Inch 9stage ThermostatSIDE on YAMAHA XJR400R, so I need to install Clamp to prevent Hose from hitting Engine and Exhaust pipe. However, only 1pc. is included in the Oil cooler kit, and in my case, I could not use the included one because I also converted to BlackHose.
That is why I purchased two 15Φ for BlackHose here.
Was the one you received as per Image?
It was just as Image.
As for the design and quality, it is neither good nor bad.
I wanted Silver, but for some reason, only Black is available for BlackHose.
Was the installation difficult?
Loosen the Bolt 4 or 5mm at the center to separate the two. Then, just loosen the Bolt4 or 5mm at the Center, and it will separate, so just bite it into the Hose and tighten the Bolt.
How was your experience with it?
It is a dedicated product, so there were no problems.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
I was a little disappointed that the 15Φ for BlackHose is only available in Black, and that the kit comes with only 1 pc. to begin with.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
add to
Purchased to prevent oil cooler hose interference View detail
ตรงปก ถูกใจ สั่งแล้วไม่ผิดหวัง View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI GPZ900R, KAWASAKI GPZ750R, KAWASAKI GPZ750R
Clean Cut
Mark the cutting point by placing a piece of masking tape around it, spray a lubricant (such as CRC) on a wide cutter knife, and cut cleanly. View detail
Quality is high, but care must be taken with Size
[How is it used?
I wanted to install ACTIVEStraightOil cooler on XJR400R, but I did not like the color of the mesh hose. For some reason, there was a Round Type with a black mesh hose, so I decided to install it as a DIY project.
How was your experience with it?
It functions well as a Heat Shrink Tube. The shrinkage is also relatively Smooth, so it is good in terms of quality.
How did it compare to other products?
It is just a Heat Shrink Tube, but it is colored to match the heat resistant hose, so it is more black than other manufacturer's products.
As for the price, I think it is a little high, partly because it is ACTIVEBrand.
Inevitably, I had to buy more, which was a moderate expense.
[Points to note]
StraightOil cooler was #6, so I bought this one #6 as well, but it was a mistake.
The Heat Shrink Tube is passed through the heat-resistant hose from the top of the mesh hose after the fitting is removed, but the hose is too exact and does not pass through properly. If you try to force it through, the mesh hose will get frayed and it will be a large disaster.
I thought it would be easier to buy #8Size because it shrinks when heat-shrunk.
I used a 19Φ made by DAYTONA in combination with the 19Φ and was able to pass it through the mesh hose without getting caught.
It would have been nice if the manufacturer could have provided a little more information about this area, but I doubt that many people would install it as a DIY project in the first place.
View detail
High quality and good, but difficult to install
[How is it used?
I wanted to install ACTIVEStraightOil cooler on XJR400R, but I did not like the color of the mesh hose. For some reason, there was a Round Type with a black mesh hose, so I decided to install it as a DIY project because I found out that it is only fixed with a shrinkable tube by applying ACTIVE heat-resistant hose over the mesh hose.
How was your experience with it?
The texture is very good.
Its smooth surface not only makes it heat resistant but also serves to prevent scratches on the car body.
How did it compare to other products?
Other manufacturers have similar products, but most of them are cheap in texture, and I think this one, made exclusively for Oil Cooler, is better.
As for the price, it is high due to the fact that it is ACTIVEBrand.
Again, I had to buy 3m worth and inevitably more, so I had to spend a moderate amount of money.
[Points to note]
The heat-resistant hose is passed through the mesh hose after the fitting has been removed, but the hose is too exact and does not pass through properly. If you try to force the hose through the mesh hose, it will be a large disaster because the mesh hose will be frayed.
The mesh hose was threaded through the end of the hose, taking care to blind the end as much as possible to avoid wisps.
I have also seen this in other reviews, but when I tried to measure the length of the hose before putting it through the mesh hose, it became too short.
It would have been nice if the manufacturer could have provided a little more information about this area, but I doubt that many people would install it as a DIY project in the first place.
View detail
![Core Guard ARMIES [TYPE-2]](https://img.webike-cdn.net/catalogue/images/3068/p161_004_TS.jpg)
ExactSize is good, but the price is Neck.
[How is it used?
ACTIVEOil cooler9Inch for XJR400R cooling performance up (10 steps) purchased
Since I do a lot of touring on rough roads, I purchased an additional oil cooler guard from the same manufacturer, ACTIVE, to protect the core.
Was the one you received as per Image?
It was as per Image, but it still looks cheap as other impressions.
I would like to see at least an engraving.
Was the installation difficult?
Installation is easy, but it is better to install the Oil coolerBody before attaching it to the vehicle body.
How was your experience with it?
There is a sense that they are well protected.
I thought it would look cool without it, but surprisingly, I did not feel uncomfortable with it on.
[Included Parts:were they on?
Instruction Manual and Sticker
[Was there anything that disappointed you?
I am worried that the Split Pin is just Steel and will soon be Rust.
The rest is cheaply made; someone who is good at DIY could make it himself.
It took a lot of courage to pay almost 4,000 yen for this.
View detail
Fits: KAWASAKI ZRX1200S, KAWASAKI ZRX1100, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R
For Dress-up
This is a customization, but there is a big difference between having a customization and not having a customization.
Installation is only a matter of replacing the oil, but I think it is best to do it at the same time as the oil replacement.
View detail
ZrXRadiator's standard
I took the plunge because my OEM Radiator was deteriorating over time and it was time to replace the Coolant.
I had read and imaged the Instruction Manual on Active's homepage before purchasing the product, so it was not so difficult to install the fan bracket. It took some time to adjust the fan bracket to the exhaust pipe.
The cooling effect is excellent. In winter, on the contrary, it may get too cold, so I am planning to take measures such as putting a board between the cores.
I like the way it looks and I think it has become quite custom.
The Bracket below looks cheap and I am hoping to do something about that.
View detail
Fits: KAWASAKI ZRX1200S, KAWASAKI ZRX1100, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R
Appearance only.
Installation is difficult.
The banjo is aluminum, so be careful to tighten Torque.
Packing is not included and must be provided.
Looks cool.
Oil leak check is a must!
View detail
For dress-up of oil cooler hose!
[How is it used?
I purchased this product for the purpose of dress-up of the mesh hose used in the oil cooler.
The Thermostat section will be more expensive due to the extra number of pieces, but it will look better.
Was the one you received as per Image?
The quality is as good as the Image and the color Anodized is Beauty.
Was the installation difficult?
Just fit it on the end of the Mesh hose, but be careful, because if it is frayed, it will stick out of the gap and stick in your finger.
How was your experience with it?
The only effect is to make it look better, since it looks like Parts.
[Included Parts:were they on?
Hose Band is included.
[Was there anything that disappointed you?
Not particularly
I am using it with ▼Earls Mesh hose and am happy with the way it looks. I am happy with the purchase, although I will need a lot of thermostats since I am using the Thermostat in between.
View detail
Oil cooler line routing
Beauty neat and tidy. View detail
![Core Guard ARMIES [TYPE-2]](https://img.webike-cdn.net/catalogue/images/3068/p161_003_TS.jpg)
Guard that does not detract from the design and cooling purpose of the Oil cooler.
I have a Bagus! Oil cooler installed, but it's not good for my mental health if I get flying rocks or bugs in it, so I bought it to protect my Core! 。 In purchasing the product, we chose this product because the Guard is not so conspicuous, it can be properly protected, and it has a fit feeling when installed.
The black color of the oil cooler does not emphasize the design after installation, and I am glad I purchased it. 。 The mesh is also Large size, so I don't think the cooling performance will be degraded. (Small insects and stones can pass through, but since cooling is the original purpose of the mesh, I don't think there is any problem with the mesh size. 。 If you put a piece of paper or something between them in the winter, you can prevent Over cool.
View detail
Excellent cooling effect
I bought this for summer cooling custom.
I think the water temperature rise is also slower than in NORMAL.
The water temperature rises when waiting at a traffic light, but drops as soon as the car starts running.
The NORMAL fan was a little melted, so I replaced it with an aluminum fan, but … the water temperature was so stable that I wondered if I would ever use it. The water temperature has stabilized to the point where I wonder if I will ever use it.
View detail
![45-Degrees Fitting [#6]](https://global.webike-cdn.net/photo/impression/80/800b55e2cd4d7df0917fed0262395e17L.jpg)
BlueRedAnodized, which is common in Oil line, to Black.
I used it on the oil cooler line of my GPZ900R.
The one that came with it was BlueRed Anodized, which was not to my liking, so I bought Black.
Since this is an Oil line work, if you are not confident about the installation, it would be better to leave it to PRO.
It does not affect performance, but the look and feel is now to my liking.
View detail